| Age | Commit message (Collapse) | Author |
|---|
|
When compiling with icc, <linux/compiler-gcc.h> ends up included
because the icc environment defines __GNUC__. Thus, we neither need
nor want to have this macro defined in both compiler-gcc.h and
compiler-intel.h, and the fact that they are inconsistent just makes
the compiler spew warnings.
Reported-by: Sunil K. Pandey <sunil.k.pandey@intel.com>
Cc: Kevin B. Smith <kevin.b.smith@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-0mbwou1zt7pafij09b897lg3@git.kernel.org
Cc: <stable@vger.kernel.org>
|
|
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
|
|
a8b14744429f ("sysfs: give different locking key to regular and bin
files") in driver-core-linus modifies sysfs_open_file() so that it
gives out different locking classes to sysfs_open_files depending on
whether the file is bin or not. Due to the massive kernfs
reorganization in driver-core-next, this naturally causes merge
conflict in fs/sysfs/file.c.
Due to the way things are split between kernfs and sysfs in
driver-core-next, the same fix can't easily be applied to
driver-core-next. This merge simply ignores the offending commit. A
following patch will implement a separate fix for the issue.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
mmp_pdma.c implements a custom of_xlate() function that is 95% identical
to what Tegra will need. Create a function to implement the common part,
so everyone doesn't just cut/paste the implementation.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
dma_request_slave_channel() simply returns NULL whenever DMA channel
lookup fails. Lookup could fail for two distinct reasons:
a) No DMA specification exists for the channel name.
This includes situations where no DMA specifications exist at all, or
other general lookup problems.
b) A DMA specification does exist, yet the driver for that channel is not
yet registered.
Case (b) should trigger deferred probe in client drivers. However, since
they have no way to differentiate the two situations, it cannot.
Implement new function dma_request_slave_channel_reason(), which performs
identically to dma_request_slave_channel(), except that it returns an
error-pointer rather than NULL, which allows callers to detect when
deferred probe should occur.
Eventually, all drivers should be converted to this new API, the old API
removed, and the new API renamed to the more desirable name. This patch
doesn't convert the existing API and all drivers in one go, since some
drivers call dma_request_slave_channel() then dma_request_channel() if
that fails. That would require either modifying dma_request_channel() in
the same way, or adding extra error-handling code to all affected
drivers, and there are close to 100 drivers using the other API, rather
than just the 15-20 or so that use dma_request_slave_channel(), which
might be tenable in a single patch.
acpi_dma_request_slave_chan_by_name() doesn't currently implement
deferred probe. It should, but this will be addressed later.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Due to USB controllers may have different restrictions, usb gadget layer
needs to provide a generic way to inform gadget functions to complain
with non-standard requirements.
This patch adds 'quirk_ep_out_aligned_size' field to struct usb_gadget
to inform when controller's epout requires buffer size to be aligned to
MaxPacketSize. A helper is also provided to align buffer size when
necessary.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch moves all bitflags to the end of usb_gadget struct in order
to improve readability.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
tclass information in now already stored in rcv_flowinfo
We do not need to store the same information twice.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation of IPV6_FLOWINFO only gives a
result if pktoptions is available (thanks to the
ip6_datagram_recv_ctl function).
It gives inconsistent results to user space, sometimes
there is a result for getsockopt(IPV6_FLOWINFO), sometimes
not.
This patch add rcv_flowinfo to store it, and return it to
the userspace in the same way than other pkt_options.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set,
several is_<foo>_ether_addr functions can be slightly
improved by using u32 dereferences.
I believe all current uses of is_zero_ether_addr and
is_broadcast_ether_addr are u16 aligned, so always use
u16 references to improve those functions performance.
Document the u16 alignment requirements.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a generic routine to test if possibly unaligned
to u16 Ethernet addresses are equal.
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set,
this uses the slightly faster generic routine
ether_addr_equal, otherwise this uses memcmp.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously inet devices were only constructed when addresses are added.
Therefore the default neigh parms values they get are the ones at the
time of these operations.
Now that we're creating inet devices earlier, this changes the behaviour
of default neigh parms values in an incompatible way (see bug #8519).
This patch creates a compromise by setting the default values at the
same point as before but only for those that have not been explicitly
set by the user since the inet device's creation.
Introduced by:
commit 8030f54499925d073a88c09f30d5d844fb1b3190
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Thu Feb 22 01:53:47 2007 +0900
[IPV4] devinet: Register inetdev earlier.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY library already reads the MII_STAT1000 and MII_LPA registers in
genphy_read_status(), so extend it to also populate the PHY device link
partner advertised features such that we can feed this back into ethtool
when asked for it in phy_ethtool_gset().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we need it elsewhere, move the inline helper function of
skb_needs_linearize() over to skbuff.h include file. While
at it, also convert the return to 'bool' instead of 'int'
and add a proper kernel doc.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently blocking in an RCU callback function will result in
"scheduling while atomic", which could be triggered for any number
of reasons. To aid debugging, this patch introduces a rcu_callback_map
that is used to tie the inappropriate voluntary context switch back
to the fact that the function is being invoked from within a callback.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The Buffalo device WZR-HP-G450H uses the index 3 for TX gain,
which is set to the high_power table currently. Later variants
of the router use the same index, but instead refer to the
low_ob_db gain table. This is not handled in the driver since
there is no way to distinguish board revisions and the high_power
table is used (incorrectly) for the newer variants.
By default, devices based on AR9300 using the TX gain index 3 have
to use the high_power table. To make sure that WZR-HP-G450H is not
broken when the high_power table is updated, use a separate array
based on information obtained from the platform data.
The current situation where only the original variant of WZR-HP-G450H
works properly stays unchanged.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
tty flip buffers use GFP_ATOMIC allocations for received data
which is to be processed by the line discipline. For each byte
received, an extra byte is used to indicate the error status of
that byte.
Instead, if the received data is error-free, encode the entire
buffer without status bytes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixup from Rafael Wysocki:
"This reverts two cpufreq commits that fixed issues for some people,
but broke things for others, so revert them and we'll need to fix the
original problems differently"
* tag 'pm-3.13-rc3-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "cpufreq: fix garbage kobjects on errors during suspend/resume"
Revert "cpufreq: suspend governors on system suspend/hibernate"
|
|
The patch moves description of the fields to the top of struct definition and
converts them to the kernel-doc format.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Change the format of the platform GPIO lookup tables to make them less
confusing and improve lookup efficiency.
The previous format was a single linked-list that required to compare
the device name and function ID of every single GPIO defined for each
lookup. Switch that to a list of per-device tables, so that the lookup
can be done in two steps, omitting the GPIOs that are not relevant for a
particular device.
The matching rules are now defined as follows:
- The device name must match *exactly*, and can be NULL for GPIOs not
assigned to a particular device,
- If the function ID in the lookup table is NULL, the con_id argument of
gpiod_get() will not be used for lookup. However, if it is defined, it
must match exactly.
- The index must always match.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 3.13-rc3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some bugfixes for the staging and IIO drivers for 3.13-rc3.
The resolve the vm memory issue in the tidspbridge driver, fix a
much-reported build failure in an ARM driver, and some other IIO
bugfixes that have been reported"
* tag 'staging-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: TIDSPBRIDGE: Use vm_iomap_memory for mmap-ing instead of remap_pfn_range
Fix build failure for gp2ap020a00f.c
iio: hid-sensors: Fix power and report state
HID: hid-sensor-hub: Add logical min and max
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.13-rc3.
Nothing major, but we seem to have an argument about a XHCI fix, so
I'm not including a revert that Sarah requested, because that breaks a
USB network driver, and I can't revert the USB network driver fix
without reintroducing other bugs that it fixed. So as it is,
everything should now be working. Worse case, I can revert the XHCI
fix before 3.13-final is out, but it seems to work well here with my
testing, so all should be good.
Other than that, some driver updates based on reports"
* tag 'usb-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: hub: Use correct reset for wedged USB3 devices that are NOTATTACHED
usb: ohci-pxa27x: include linux/dma-mapping.h
USB: cdc-acm: Added support for the Lenovo RD02-D400 USB Modem
usb: tools: fix a regression issue that gcc can't link to pthread
USB: switch maintainership of chipidea to Peter
USB: pl2303: fixed handling of CS5 setting
USB: ftdi_sio: fixed handling of unsupported CSIZE setting
USB: mos7840: correct handling of CS5 setting
USB: spcp8x5: correct handling of CS5 setting
usb: wusbcore: fix deadlock in wusbhc_gtk_rekey
usb: wusbcore: do device lookup while holding the hc mutex
usb: wusbcore: send keepalives to unauthenticated devices
USB: option: support new huawei devices
USB: serial: option: blacklist interface 1 for Huawei E173s-6
usb: xhci: Link TRB must not occur within a USB payload burst
usb: gadget: f_mass_storage: call try_to_freeze only when its safe
usb: gadget: tcm_usb_gadget: mark bot_cleanup_old_alt static
usb: gadget: ffs: fix sparse warning
usb: gadget: zero: module parameters can be static
usb: gadget: storage: fix sparse warning
...
|
|
When CONFIG_FW_LOADER_USER_HELPER is set, request_firmware() falls
back to the usermode helper for loading via udev when the direct
loading fails. But the recent udev takes way too long timeout (60
seconds) for non-existing firmware. This is unacceptable for the
drivers like microcode loader where they load firmwares optionally,
i.e. it's no error even if no requested file exists.
This patch provides a new helper function, request_firmware_direct().
It behaves as same as request_firmware() except for that it doesn't
fall back to usermode helper but returns an error immediately if the
f/w can't be loaded directly in kernel.
Without CONFIG_FW_LOADER_USER_HELPER=y, request_firmware_direct() is
just an alias of request_firmware(), due to obvious reason.
Tested-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds remove_phy flag to the HCD structure. If the flag is
set and if hcd->phy is valid, the phy is shutdown and released
whenever usb_add_hcd fails or usb_hcd_remove is called.
This can be used by the HCD drivers to auto-remove
the external USB phy when it is no longer needed.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sg_copy_buffer() can't meet demand for some drrivers(such usb
mass storage), so we have to use the sg_miter_* APIs to access
sg buffer, then need export sg_miter_skip() for these drivers.
The API is needed for converting to sg_miter_* APIs in USB storage
driver for accessing sg buffer.
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add mx6 hdmi transmitter support.
Original work has been done by Sascha Hauer and Tony Prisk.
Special thanks to Russell King for his carefully review, many bug fixes and
testing of the mx6 HDMI driver.
Tested on the following boards:
- mx6q sabresd
- mx6dl sabresd
- mx6solo wandboard
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Making DMA RX polling optional when DMA is on was just
over-cautious: there is one single system in the kernel tree
using this facility, Ux500 and after some testing I turned
this on also for Ux500, which means it should simply be on
by default if DMA is enabled.
Cc: Jongsung Kim <neidhard.kim@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no in-tree user of tty_prepare_flip_string_flags(); remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Trim up the memory_used field name to mem_used.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow driver to configure its maximum flip buffer memory
consumption/limit. This is necessary for very-high speed line
rates (in excess of 10MB/sec) because the flip buffers can
be saturated before the line discipline has a chance to
throttle the input.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most line disciplines already handle the undocumented NULL flag
ptr in their .receive_buf method; however, several don't.
Document the NULL flag ptr, and correct handling in the
N_MOUSE, N_GSM0710 and N_R394 line disciplines.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
change_prot_numa should work even if _PAGE_NUMA != _PAGE_PROTNONE.
On archs like ppc64 that don't use _PAGE_PROTNONE and also have
a separate page table outside linux pagetable, we just need to
make sure that when calling change_prot_numa we flush the
hardware page table entry so that next page access result in a numa
fault.
We still need to make sure we use the numa faulting logic only
when CONFIG_NUMA_BALANCING is set. This implies the migrate-on-fault
(Lazy migration) via mbind will only work if CONFIG_NUMA_BALANCING
is set.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Now that all drivers have been converted to the new event config interface we
can remove for the legacy event config interface. Also drop the '_new' suffix
for the event config interface callbacks, since those are the only callbacks
now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Commit 5a87182aa21d (cpufreq: suspend governors on system
suspend/hibernate) causes hibernation problems to happen on
Bjørn Mork's and Paul Bolle's systems, so revert it.
Fixes: 5a87182aa21d (cpufreq: suspend governors on system suspend/hibernate)
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a flag to tell the PCI subsystem that kernel is shutting down in
preparation to kexec a kernel. Add code in PCI subsystem to use this flag
to clear Bus Master bit on PCI devices only in case of kexec reboot.
This fixes a power-off problem on Acer Aspire V5-573G and likely other
machines and avoids any other issues caused by clearing Bus Master bit on
PCI devices in normal shutdown path. The problem was introduced by
b566a22c2332 ("PCI: disable Bus Master on PCI device shutdown").
This patch is based on discussion at
http://marc.info/?l=linux-pci&m=138425645204355&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63861
Reported-by: Chang Liu <cl91tp@gmail.com>
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: stable@vger.kernel.org # v3.5+
|
|
To avoid build problems and breaking dependencies between ACPI header
files, <acpi/acpi.h> should not be included directly by code outside
of the ACPI core subsystem, but this is done by the ACPI iSCSI
Boot Firmware code.
The iBFT specification doesn't mention whether or not it can appear
on a non-ACPI platform, but is says that ACPI 3.0b defines the
mechanism. The current CONFIG_ISCSI_IBFT_FIND code doesn't use the
ACPI tables API to locate the table, so it doesn't rely on CONFIG_ACPI
directly.
However, since iBFT is is an ACPI-based mechanism (please refer to
the documentation link below for more information), it should be
correct to make CONFIG_ISCSI_IBFT_FIND depend on CONFIG_ACPI (even
though the table location can be implemented without using ACPI
tables API).
After that change, include/linux/iscsi_ibft.h can be modified to
include <linux/acpi.h> instead of <acpi/acpi.h> as appropriate.
References: http://www.microsoft.com/whdc/system/platform/firmware/ibft.mspx
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Peter Jones <pjones@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To avoid build problems and breaking dependencies between ACPI header
files, <acpi/acpi.h> should not be included directly by code outside
of the ACPI core subsystem. However, that is possible if
<linux/acpi_io.h> is included, because that file contains
a direct inclusion of <acpi/acpi.h>.
For this reason, remove the direct <acpi/acpi.h> inclusion from
<linux/acpi_io.h>, move that file from include/linux/ to include/acpi/
and make <linux/acpi.h> include it for CONFIG_ACPI set along with the
other ACPI header files. Accordingly, Remove the inclusions of
<linux/acpi_io.h> from everywhere.
Of course, that causes the contents of the new <acpi/acpi_io.h> file
to be available for CONFIG_ACPI set only, so intel_opregion.o that
depends on it should also depend on CONFIG_ACPI (and it really should
not be compiled for CONFIG_ACPI unset anyway).
References: https://01.org/linuxgraphics/sites/default/files/documentation/acpi_igd_opregion_spec.pdf
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The following warnings can be seen in W=1 builds, because the original
sfi_acpi.[ch] header inclusions are incorrect:
include/linux/sfi_acpi.h:72:2: error: implicit declaration of function 'acpi_table_parse' [-Werror=implicit-function-declaration]
drivers/sfi/sfi_acpi.c:154:5: warning: no previous prototype for 'sfi_acpi_table_parse' [-Wmissing-prototypes]
Fix linux/sfi_acpi.h and modify drivers/sfi/sfi_acpi.c accordingly.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Modify acpi_preset_companion() to take a struct acpi_device pointer
instead of an ACPI handle as its second argument and redefine it as
a static inline wrapper around ACPI_COMPANION_SET() passing the
return value of acpi_find_child_device() directly as the second
argument to it. Update its users to pass struct acpi_device
pointers instead of ACPI handles to it.
This allows some unnecessary acpi_bus_get_device() calls to be
avoided.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Aaron Lu <aaron.lu@intel.com> # for ATA binding
|
|
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a new check for CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to reduce
the number of or's used in the ether_addr_equal comparison to very
slightly improve function performance.
Simplify the ether_addr_equal_64bits implementation.
Integrate and remove the zap_last_2bytes helper as it's now
used only once.
Remove the now unused compare_ether_addr function.
Update the unaligned-memory-access documentation to remove the
compare_ether_addr description and show how unaligned accesses
could occur with ether_addr_equal.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add extcon field to platform data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Move omap_usb_config to platform data, so that OTG driver can include it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Some network drivers use dev_kfree_skb_any() and dev_kfree_skb_irq()
helpers to free skbs, both for dropped packets and TX completed ones.
We need to separate the two causes to get better diagnostics
given by dropwatch or "perf record -e skb:kfree_skb"
This patch provides two new helpers, dev_consume_skb_any() and
dev_consume_skb_irq() to be used for consumed skbs.
__dev_kfree_skb_irq() is slightly optimized to remove one
atomic_dec_and_test() in fast path, and use this_cpu_{r|w} accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the previous patch which introduced for_each_css(),
for_each_root_subsys() only has two users left. This patch replaces
it with for_each_subsys() + explicit subsys_mask testing and remove
for_each_root_subsys() along with cgroupfs_root->subsys_list handling.
This patch doesn't introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
|
