| Age | Commit message (Collapse) | Author |
|---|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() returns signed status. It should be stored and
compared as signed value before storing to unsigned variable. Implicit
conversion from signed to unsigned and then comparison with less than
zero is wrong as unsigned value can never be less than zero.
Fixes: f087f01ca2c5 ("serial: lantiq: Use platform_get_irq() to get the interrupt")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/YcIf7+oSWWn34ND6@debian-BULLSEYE-live-builder-AMD64
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct uart_8250_port contains mcr_mask and mcr_force members whose
sole purpose is to work around an Alpha-specific quirk. This code
doesn't belong in the core where it is executed by everyone else,
so move it to a proper ->set_mctrl callback which is used on the
affected Alpha machine only.
The quirk was introduced in January 1995:
https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/diff/drivers/char/serial.c?h=1.1.83
The members in struct uart_8250_port were added in 2002:
https://git.kernel.org/history/history/c/4524aad27854
The quirk applies to non-PCI Alphas and arch/alpha/Kconfig specifies
"select FORCE_PCI if !ALPHA_JENSEN". So apparently the only affected
machine is the EISA-based Jensen that Linus was working on back then:
https://lore.kernel.org/all/CAHk-=wj1JWZ3sCrGz16nxEj7=0O+srMg6Ah3iPTDXSPKEws_SA@mail.gmail.com/
Up until now the quirk is not applied unless CONFIG_PCI is disabled.
If users forget to do that or run a generic Alpha kernel, the serial
ports aren't usable on Jensen. Avoid by confining the quirk to
CONFIG_ALPHA_JENSEN instead of !CONFIG_PCI. On generic Alpha kernels,
auto-detect at runtime whether the quirk needs to be applied.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Ulrich Teichert <krypton@ulrich-teichert.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/b83d069cb516549b8a5420e097bb6bdd806f36fc.1640695609.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit a6845e1e1b78 ("serial: core: Consider rs485 settings to drive
RTS") sought to deassert RTS when opening an rs485-enabled uart port.
That way, the transceiver does not occupy the bus until it transmits
data.
Unfortunately, the commit mixed up the logic and *asserted* RTS instead
of *deasserting* it:
The commit amended uart_port_dtr_rts(), which raises DTR and RTS when
opening an rs232 port. "Raising" actually means lowering the signal
that's coming out of the uart, because an rs232 transceiver not only
changes a signal's voltage level, it also *inverts* the signal. See
the simplified schematic in the MAX232 datasheet for an example:
https://www.ti.com/lit/ds/symlink/max232.pdf
So, to raise RTS on an rs232 port, TIOCM_RTS is *set* in port->mctrl
and that results in the signal being driven low.
In contrast to rs232, the signal level for rs485 Transmit Enable is the
identity, not the inversion: If the transceiver expects a "high" RTS
signal for Transmit Enable, the signal coming out of the uart must also
be high, so TIOCM_RTS must be *cleared* in port->mctrl.
The commit did the exact opposite, but it's easy to see why given the
confusing semantics of rs232 and rs485. Fix it.
Fixes: a6845e1e1b78 ("serial: core: Consider rs485 settings to drive RTS")
Cc: stable@vger.kernel.org # v4.14+
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9395767847833f2f3193c49cde38501eeb3b5669.1639821059.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Note: I am using a small test app + driver located at [0] for the
problem description. serco is a driver whose write function dispatches
to the serial controller. sertest is a user-mode app that writes n bytes
to the serial console using the serco driver.
While investigating a bug in the RHEL kernel, I noticed that the serial
console throughput is way below the configured speed of 115200 bps in
a HP Proliant DL380 Gen9. I was expecting something above 10KB/s, but
I got 2.5KB/s.
$ time ./sertest -n 2500 /tmp/serco
real 0m0.997s
user 0m0.000s
sys 0m0.997s
With the help of the function tracer, I then noticed the serial
controller was taking around 410us seconds to dispatch one single byte:
$ trace-cmd record -p function_graph -g serial8250_console_write \
./sertest -n 1 /tmp/serco
$ trace-cmd report
| serial8250_console_write() {
0.384 us | _raw_spin_lock_irqsave();
1.836 us | io_serial_in();
1.667 us | io_serial_out();
| uart_console_write() {
| serial8250_console_putchar() {
| wait_for_xmitr() {
1.870 us | io_serial_in();
2.238 us | }
1.737 us | io_serial_out();
4.318 us | }
4.675 us | }
| wait_for_xmitr() {
1.635 us | io_serial_in();
| __const_udelay() {
1.125 us | delay_tsc();
1.429 us | }
...
...
...
1.683 us | io_serial_in();
| __const_udelay() {
1.248 us | delay_tsc();
1.486 us | }
1.671 us | io_serial_in();
411.342 us | }
In another machine, I measured a throughput of 11.5KB/s, with the serial
controller taking between 80-90us to send each byte. That matches the
expected throughput for a configuration of 115200 bps.
This patch changes the serial8250_console_write to use the 16550 fifo
if available. In my benchmarks I got around 25% improvement in the slow
machine, and no performance penalty in the fast machine.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20211222112831.1968392-2-wander@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update the SCIF serial driver to remove printouts for break, frame, parity
and overrun errors. This reduces the amount of console printouts generated
by the defconfig kernel on R-Car Gen3 for certain use cases. To retrieve
more information about such errors the user may inspect counters. Also these
errors are fed into the TTY layer for further application specific handling.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Link: https://lore.kernel.org/r/163884254093.18109.2982470198301927679.sendpatchset@octo
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's better to stick with standard API to write and read DL value
when the hardware is compatible with it. In case any quirks are
needed it may be easily added in one place rather than modifying
code here and there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122133512.8947-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add UPF_MAGIC_MULTIPLIER to the port flags since there is now
range checking in serial8250_get_baud_rate() in 8250_port.c.
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122133512.8947-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pericom along with Acces I/O support consumes a lot of LOCs in 8250_pci.c.
For the sake of easier maintenance, split it to a separate driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122133512.8947-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On modern Exynos SoCs (like Exynos850) the UART can be implemented as a
part of USI IP-core. In such case, USI driver is used to initialize USI
registers, and it also calls of_platform_populate() to instantiate all
sub-nodes (e.g. serial node) of USI node. When serial driver is
built-in, but USI driver is a module, and CONFIG_SERIAL_SAMSUNG_CONSOLE
is enabled, next call chain will happen when loading USI module from
user space:
usi_init
v
usi_probe
v
of_platform_populate
v
s3c24xx_serial_probe
v
uart_add_one_port
v
uart_configure_port
v
register_console
v
try_enable_new_console
v
s3c24xx_serial_console_setup
But because the serial driver is built-in, and
s3c24xx_serial_console_setup() is marked with __init keyword, that
symbol will discarded and long gone by that time already, causing failed
paging request.
That happens during the next config combination:
EXYNOS_USI=m
SERIAL_SAMSUNG=y
SERIAL_SAMSUNG_CONSOLE=y
That config should be completely possible, so rather than limiting
SERIAL_SAMSUNG choice to "m" only when USI=m, remove __init keyword for
all affected functions.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211204195757.8600-6-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable serial driver to be built as a module. To do so, init the console
support on driver/module load instead of using console_initcall().
Inspired by commit 87a0b9f98ac5 ("tty: serial: meson: enable console as
module").
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211204195757.8600-5-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USI control is now extracted to the dedicated USI driver. Remove USI
related code from serial driver to avoid conflicts and code duplication.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211204195757.8600-4-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable tmp is being masked with a bitmask and the value is being
written to port base + 0x3c. However, the masked value is being written
back to tmp and tmp is never used after this. The assignmentment is
redundant, replace the &= operator with just &.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewesd-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211205232822.110099-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for i.MXRT1050's uart.
Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Link: https://lore.kernel.org/r/20211215220538.4180616-8-Mr.Bossman075@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Accessing platform device resources directly has long been deprecated for
DT as IRQ resources may not be available at device creation time. Drivers
continuing to use static IRQ resources is blocking removing the static setup
from the DT core code.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215224832.1985402-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sh-sci driver supports up to four input clocks, of which only the
first one is mandatory.
Replace devm_clk_get() and custom error checking by
devm_clk_get_optional(), to simplify the code and to catch all real
errors.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/bce27288cb570952dd96b441e1af8768ad8b4870.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the dev_err_probe() helper to streamline error handling.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5c4dd8df1f8d0d14786f26ee80b77f3eb8e06cd5.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 1b463bd51042927e ("ARM: dts: r8a7794: Rename the serial
port clock to fck") in v4.6, all upstream DTS files call the SCIF
functional clock "fck".
Hence the time is ripe to drop backward-compatibility with old DTBs that
use the old "sci_ick" name.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b4103e44d6ac46b6c1c264e2aeac80b39941fe74.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the preferred platform_get_irq() call to retrieve the interrupts. These
have the advantage of working with deferred probe and gets us one step
closer to removing of_irq_to_resource_table().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215224800.1984391-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add serial support for R-Car Gen4 SoC.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20211209070817.1223888-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.
For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.
Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae5b ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d44f ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c624 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial driver fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a small window in time during resume where the hardware
flow control signal RTS can be asserted (which allows a sender to
resume sending data to the UART) but the baud rate has not yet
been restored. This will cause corrupted data and FRAMING, OVERRUN
and BREAK errors. This is happening because the MCTRL register is
shadowed in uart_port struct and is later used during resume to set
the MCTRL register during both serial8250_do_startup() and
uart_resume_port(). Unfortunately, serial8250_do_startup()
happens before the UART baud rate is restored. The fix is to clear
the shadowed mctrl value at the end of suspend and restore it at the
end of resume.
Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With commit 3873e2d7f63a ("drivers: PL011: refactor pl011_probe()") the
function devm_ioremap() called from pl011_setup_port() was replaced with
devm_ioremap_resource(). Since this function not only remaps but also
requests the ports io memory region it now collides with the .config_port()
callback which requests the same region at uart port registration.
Since devm_ioremap_resource() already claims the memory successfully, the
request in .config_port() fails.
Later at uart port deregistration the attempt to release the unclaimed
memory also fails. The failure results in a “Trying to free nonexistent
resource" warning.
Fix these issues by removing the callbacks that implement the redundant
memory allocation/release. Also make sure that changing the drivers io
memory base address via TIOCSSERIAL is not allowed any more.
Fixes: 3873e2d7f63a ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20211129174238.8333-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The base address of uartlite registers could be 64 bit address which is from
device resource. When ulite_probe() calls ulite_assign(), this 64 bit
address is casted to 32-bit. The fix is to replace "u32" type with
"phys_addr_t" type for the base address in ulite_assign() argument list.
Fixes: 8fa7b6100693 ("[POWERPC] Uartlite: Separate the bus binding from the driver proper")
Signed-off-by: Lizhi Hou <lizhi.hou@xilinx.com>
Link: https://lore.kernel.org/r/20211129202302.1319033-1-lizhi.hou@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use wait_event_interruptible in lpuart_dma_shutdown isn't a reasonable
behavior, since it may cause the system hang here if the condition
!sport->dma_tx_in_progress never to be true in some corner case, such as
when enable the flow control, the dma tx request may never be completed
due to the peer's CTS setting when run .shutdown().
So here change to use wait_event_interruptible_timeout instead of
wait_event_interruptible, the tx dma will be forcibly terminated if the
tx dma request cannot be completed within 300ms.
Considering the worst tx dma case is to have a 4K bytes tx buffer, which
would require about 300ms to complete when the baudrate is 115200.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211203030441.22873-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver wrongly assummed that tx_submit() will start the transfer,
which is not the case, now that the at_xdmac driver is fixed. tx_submit
is supposed to push the current transaction descriptor to a pending queue,
waiting for issue_pending to be called. issue_pending must start the
transfer, not tx_submit.
Fixes: 34df42f59a60 ("serial: at91: add rx dma support")
Fixes: 08f738be88bb ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211125090028.786832-4-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tx_submit() method of struct dma_async_tx_descriptor is entitled
to do sanity checks and return errors if encountered. It's not the
case for the DMA controller drivers that this client is using
(at_h/xdmac), because they currently don't do sanity checks and always
return a positive cookie at tx_submit() method. In case the controller
drivers will implement sanity checks and return errors, print a message
so that the client will be informed that something went wrong at
tx_submit() level.
Fixes: 08f738be88bb ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20211125090028.786832-3-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it
and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port.
Fixes: 78d3820b9bd3 ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit f45709df7731 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df7731 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().
Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller. Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clear RTSD status before enabling the irq event for RTSD in
imx_uart_enable_wakeup function.
Since RTSD can be set as the wakeup source, this can avoid any risk of
false triggering of a wake-up interrupts.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125014306.4432-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit a9c3f68f3cd8d (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). We are
going to remove the latter (as it is used less), so call the former in
drivers/tty/.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the StarFive JH7100 RISC-V SoC the UART core clocks can't be set to
exactly 16 * 115200Hz and many other common bitrates. Trying this will
only result in a higher input clock, but low enough that the UART's
internal divisor can't come close enough to the baud rate target.
So rather than try to set the input clock it's better to skip the
clk_set_rate call and rely solely on the UART's internal divisor.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211116150119.2171-15-kernel@esmil.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in sh-sci driver.
This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.
Also, propagate the error to the caller of sci_parse_dt() instead of
returning NULL in case of failure.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are two consequent checks of uport != NULL in
uart_port_shutdown(). Join these two under a single block.
De-multiline the comments when shuffling with them anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 89d4f98ae90d ("ARM: remove zte zx platform") missed to remove some
definitions for this platform's debug and serial, e.g., code dependent on
the config DEBUG_ZTE_ZX.
Fortunately, ./scripts/checkkconfigsymbols.py detects this and warns:
DEBUG_ZTE_ZX
Referencing files: arch/arm/include/debug/pl01x.S
Further review by Arnd Bergmann identified even more dead code in the
amba serial driver.
Remove all this left-over from the zte zx platform.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211102063810.932-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jing Yao <yao.jing2@zte.com.cn>
Link: https://lore.kernel.org/r/20211104114754.30983-1-yao.jing2@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Revert commit b4b844930f27 ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.
This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.
Fixes: d781ec21bae6 ("serial: tegra: report clk rate errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Patrik John <patrik.john@u-blox.com>
Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LITEX symbol is neither a build or runtime dependency for the
liteuart serial driver.
LITEX is selected by the "LiteX SoC Controller" driver, which does a
probe-time register-access sanity check and panics if the SoC has not
been configured correctly. That driver's Kconfig entry asserts that any
LiteX driver using the LiteX register accessors should depend on LITEX,
but currently only the serial driver complies.
Relax this LITEX "dependency" in order to make it easier to compile test
the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to release the allocated minor number before returning on
probe errors.
Fixes: 1da81e5562fa ("drivers/tty/serial: add LiteUART driver")
Cc: stable@vger.kernel.org # 5.11
Cc: Filip Kokosinski <fkokosinski@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Deregister the port when unbinding the driver to prevent it from being
used after releasing the driver data and leaking memory allocated by
serial core.
Fixes: 1da81e5562fa ("drivers/tty/serial: add LiteUART driver")
Cc: stable@vger.kernel.org # 5.11
Cc: Filip Kokosinski <fkokosinski@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drvdata has to be set in _probe() - otherwise platform_get_drvdata()
causes null pointer dereference BUG in _remove().
Fixes: 1da81e5562fa ("drivers/tty/serial: add LiteUART driver")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilia Sergachev <silia@ethz.ch>
Link: https://lore.kernel.org/r/20211115224944.23f8c12b@dtkw
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
Fixes: 99693945013a ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 761ed4a94582 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e46e ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145ace ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a94582 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
