| Age | Commit message (Collapse) | Author |
|---|
|
commit 3cd2018e15b3d66d2187d92867e265f45ad79e6f upstream.
Since commit d24cfee7f63d ("spi: Fix acpi deferred irq probe"), the
acpi_dev_gpio_irq_get() call gets delayed till spi_probe() is called
on the SPI device.
If there is no driver for the SPI device then the move to spi_probe()
results in acpi_dev_gpio_irq_get() never getting called. This may
cause problems by leaving the GPIO pin floating because this call is
responsible for setting up the GPIO pin direction and/or bias according
to the values from the ACPI tables.
Re-add the removed acpi_dev_gpio_irq_get() in acpi_register_spi_device()
to ensure the GPIO pin is always correctly setup, while keeping the
acpi_dev_gpio_irq_get() call added to spi_probe() to deal with
-EPROBE_DEFER returns caused by the GPIO controller not having a driver
yet.
Link: https://bbs.archlinux.org/viewtopic.php?id=302348
Fixes: d24cfee7f63d ("spi: Fix acpi deferred irq probe")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Link: https://patch.msgid.link/20251102190921.30068-1-hansg@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b832b19318534bb4f1673b24d78037fee339c679 ]
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://patch.msgid.link/20250811-restricted-pointers-spi-v1-1-32c47f954e4d@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e811b088a3641861fc9d2b2b840efc61a0f1907d ]
In DMA mode fsl_lpspi_reset() is always called at the end, even when the
transfer is aborted. In PIO mode aborts skip the reset leaving the FIFO
filled and the module enabled.
Fix it by always calling fsl_lpspi_reset().
Fixes: a15dc3d657fa ("spi: lpspi: Fix CLK pin becomes low before one transfer")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://patch.msgid.link/20250828-james-nxp-lpspi-v2-3-6262b9aa9be4@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbe33705864ba2697a2939de715b81538cf32430 ]
The driver currently supports multiple chip-selects, but only sets the
polarity for the first one (CS 0). Fix it by setting the PCSPOL bit for
the desired chip-select.
Fixes: 5314987de5e5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250828-james-nxp-lpspi-v2-2-6262b9aa9be4@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 782a7c73078e1301c0c427f21c06377d77dfa541 ]
Commit 6a130448498c ("spi: lpspi: Fix wrong transmission when don't use
CONT") breaks transmissions when CONT is used. The TDIE interrupt should
not be disabled in all cases. If CONT is used and the TX transfer is not
yet completed yet, but the interrupt handler is called because there are
characters to be received, TDIE is replaced with FCIE. When the transfer
is finally completed, SR_TDF is set but the interrupt handler isn't
called again.
Fixes: 6a130448498c ("spi: lpspi: Fix wrong transmission when don't use CONT")
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250828-james-nxp-lpspi-v2-1-6262b9aa9be4@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fa60c094c19b97e103d653f528f8d9c178b6a5f5 ]
In target mode, extra interrupts can be received between the end of a
transfer and halting the module if the host continues sending more data.
If the interrupt from this occurs after the reinit_completion() then the
completion counter is left at a non-zero value. The next unrelated
transfer initiated by userspace will then complete immediately without
waiting for the interrupt or writing to the RX buffer.
Fix it by resetting the counter before the transfer so that lingering
values are cleared. This is done after clearing the FIFOs and the
status register but before the transfer is initiated, so no interrupts
should be received at this point resulting in other race conditions.
Fixes: 4f5ee75ea171 ("spi: spi-fsl-dspi: Replace interruptible wait queue with a simple completion")
Signed-off-by: James Clark <james.clark@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250627-james-nxp-spi-dma-v4-1-178dba20c120@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 826b3a6a34619b934cdc33eeb961fcb99ce92c09 ]
Interrupts are not necessary for DMA functionality, since the completion
event is provided by the DMA driver.
But if the driver fails to request the IRQ defined in the device tree,
it will call dspi_poll which would make the driver hang waiting for data
to become available in the RX FIFO.
Fixes: c55be3059159 ("spi: spi-fsl-dspi: Use poll mode in case the platform IRQ is missing")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-9-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: fa60c094c19b ("spi: spi-fsl-dspi: Clear completion counter before initiating transfer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 547248fbed23f3cd2f6a5937b44fad60993640c4 ]
These function names are very generic and it is easy to get confused.
Rename them after the hardware register that they are accessing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-6-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: fa60c094c19b ("spi: spi-fsl-dspi: Clear completion counter before initiating transfer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0941d5166629cb766000530945e54b4e49680c68 ]
The maximum amount of data to transfer in a single DMA request is
calculated from the FIFO sizes (which is technically not 100% correct,
but a simplification, as it is limited by the maximum word count values
in the Transmit and Control Data Registers). However, in case there is
both data to transmit and to receive, the transmit limit is overwritten
by the receive limit.
Fix this by using the minimum applicable FIFO size instead. Move the
calculation outside the loop, so it is not repeated for each individual
DMA transfer.
As currently tx_fifo_size is always equal to rx_fifo_size, this bug had
no real impact.
Fixes: fe78d0b7691c0274 ("spi: sh-msiof: Fix FIFO size to 64 word from 256 word")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/d9961767a97758b2614f2ee8afe1bd56dc900a60.1747401908.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fb98bd0a13de2c9d96cb5c00c81b5ca118ac9d71 ]
The SPI interface is activated before the CPOL setting is applied. In
that moment, the clock idles high and CS goes low. After a short delay,
CPOL and other settings are applied, which may cause the clock to change
state and idle low. This transition is not part of a clock cycle, and it
can confuse the receiving device.
To prevent this unexpected transition, activate the interface while CPOL
and the other settings are being applied.
Signed-off-by: Alessandro Grassi <alessandro.grassi@mailbox.org>
Link: https://patch.msgid.link/20250502095520.13825-1-alessandro.grassi@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 283ae0c65e9c592f4a1ba4f31917f5e766da7f31 ]
DSPI registers are NOT continuous, some registers are reserved and
accessing them from userspace will trigger external abort, add regmap
register access table to avoid below abort.
For example on S32G:
# cat /sys/kernel/debug/regmap/401d8000.spi/registers
Internal error: synchronous external abort: 96000210 1 PREEMPT SMP
...
Call trace:
regmap_mmio_read32le+0x24/0x48
regmap_mmio_read+0x48/0x70
_regmap_bus_reg_read+0x38/0x48
_regmap_read+0x68/0x1b0
regmap_read+0x50/0x78
regmap_read_debugfs+0x120/0x338
Fixes: 1acbdeb92c87 ("spi/fsl-dspi: Convert to use regmap and add big-endian support")
Co-developed-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://patch.msgid.link/20250522-james-nxp-spi-v2-1-bea884630cfb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a73fa3690a1f3014d6677e368dce4e70767a6ba2 ]
spi_test_print_hex_dump() prints buffers holding less than 1024 bytes in
full. Larger buffers are truncated: only the first 512 and the last 512
bytes are printed, separated by a truncation message. The latter is
confusing in case the buffer holds exactly 1024 bytes, as all data is
printed anyway.
Fix this by printing buffers holding up to and including 1024 bytes in
full.
Fixes: 84e0c4e5e2c4ef42 ("spi: add loopback test driver to allow for spi_master regression tests")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/37ee1bc90c6554c9347040adabf04188c8f704aa.1746184171.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 269e31aecdd0b70f53a05def79480f15cbcc0fd6 upstream.
There was a change in the mxs-dma engine that uses a new custom flag.
The change was not applied to the mxs spi driver.
This results in chipselect being deasserted too early.
This fixes the chipselect problem by using the new flag in the mxs-spi
driver.
Fixes: ceeeb99cd821 ("dmaengine: mxs: rename custom flag")
Signed-off-by: Ralf Schlatterbeck <rsc@runtux.com>
Link: https://msgid.link/r/20240202115330.wxkbfmvd76sy3a6a@runtux.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 984836621aad98802d92c4a3047114cf518074c8 ]
If we remove the module which will call mpc52xx_spi_remove
it will free 'ms' through spi_unregister_controller.
while the work ms->work will be used. The sequence of operations
that may lead to a UAF bug.
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in mpc52xx_spi_remove.
Fixes: ca632f556697 ("spi: reorganize drivers")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://patch.msgid.link/1f16f8ae0e50ca9adb1dc849bf2ac65a40c9ceb9.1732783000.git.xiaopei01@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d24cfee7f63d6b44d45a67c5662bd1cc48e8b3ca upstream.
When probing spi device take care of deferred probe of ACPI irq gpio
similar like for OF/DT case.
>From practical standpoint this fixes issue with vsc-tp driver on
Dell XP 9340 laptop, which try to request interrupt with spi->irq
equal to -EPROBE_DEFER and fail to probe with the following error:
vsc-tp spi-INTC10D0:00: probe with driver vsc-tp failed with error -22
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: 33ada67da352 ("ACPI / spi: attach GPIO IRQ from ACPI description to SPI device")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com> # Dell XPS9320, ov01a10
Link: https://patch.msgid.link/20241122094224.226773-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c53b45c71b4920b5e62f0ea8079a1da382b9434 upstream.
Commit 6098475d4cb4 ("spi: Fix deadlock when adding SPI controllers on
SPI buses") introduced a per-controller mutex. But mutex_unlock() of
said lock is called after the controller is already freed:
spi_unregister_controller(ctlr)
-> put_device(&ctlr->dev)
-> spi_controller_release(dev)
-> mutex_unlock(&ctrl->add_lock)
Move the put_device() after the mutex_unlock().
Fixes: 6098475d4cb4 ("spi: Fix deadlock when adding SPI controllers on SPI buses")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.15
Link: https://lore.kernel.org/r/20211111083713.3335171-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6098475d4cb48d821bdf453c61118c56e26294f0 upstream.
Currently we have a global spi_add_lock which we take when adding new
devices so that we can check that we're not trying to reuse a chip
select that's already controlled. This means that if the SPI device is
itself a SPI controller and triggers the instantiation of further SPI
devices we trigger a deadlock as we try to register and instantiate
those devices while in the process of doing so for the parent controller
and hence already holding the global spi_add_lock. Since we only care
about concurrency within a single SPI bus move the lock to be per
controller, avoiding the deadlock.
This can be easily triggered in the case of spi-mux.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Hardik Gohil <hgohil@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 909f34f2462a99bf876f64c5c61c653213e32fce upstream.
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from platform_device_id table.
Fixes: 44d8fb30941d ("spi/bcm63xx: move register definitions into the driver")
Cc: stable@vger.kernel.org
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20240819123349.4020472-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 68a16708d2503b6303d67abd43801e2ca40c208d ]
In the s3c64xx_flush_fifo() code, the loops counter is post-decremented
in the do { } while(test && loops--) condition. This means the loops is
left at the unsigned equivalent of -1 if the loop times out. The test
after will never pass as if tests for loops == 0.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Fixes: 230d42d422e7 ("spi: Add s3c64xx SPI Controller driver")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://patch.msgid.link/20240924134009.116247-2-ben.dooks@codethink.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7781f1d120fec8624fc654eda900fc8748262082 ]
0 is incorrect error code when failed to parse and map IRQ.
Replace OF specific old API for IRQ retrieval with a generic
one to fix this issue.
Fixes: 0f245463b01e ("spi: ppc4xx: handle irq_of_parse_and_map() errors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20240814144525.2648450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f245463b01ea254ae90e1d0389e90b0e7d8dc75 ]
Zero and negative number is not a valid IRQ for in-kernel code and the
irq_of_parse_and_map() function returns zero on error. So this check for
valid IRQs should only accept values > 0.
Fixes: 44dab88e7cc9 ("spi: add spi_ppc4xx driver")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://patch.msgid.link/20240724084047.1506084-1-make24@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 709df70a20e990d262c473ad9899314039e8ec82 ]
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://patch.msgid.link/20240831094231.795024-1-liaochen4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2a8787c1cdc7be24fdd8953ecd1a8743a1006235 upstream.
Change the memcpy length to fix the out-of-bounds issue when writing the
data that is not 4 byte aligned to TX FIFO.
To reproduce the issue, write 3 bytes data to NOR chip.
dd if=3b of=/dev/mtd0
[ 36.926103] ==================================================================
[ 36.933409] BUG: KASAN: slab-out-of-bounds in nxp_fspi_exec_op+0x26ec/0x2838
[ 36.940514] Read of size 4 at addr ffff00081037c2a0 by task dd/455
[ 36.946721]
[ 36.948235] CPU: 3 UID: 0 PID: 455 Comm: dd Not tainted 6.11.0-rc5-gc7b0e37c8434 #1070
[ 36.956185] Hardware name: Freescale i.MX8QM MEK (DT)
[ 36.961260] Call trace:
[ 36.963723] dump_backtrace+0x90/0xe8
[ 36.967414] show_stack+0x18/0x24
[ 36.970749] dump_stack_lvl+0x78/0x90
[ 36.974451] print_report+0x114/0x5cc
[ 36.978151] kasan_report+0xa4/0xf0
[ 36.981670] __asan_report_load_n_noabort+0x1c/0x28
[ 36.986587] nxp_fspi_exec_op+0x26ec/0x2838
[ 36.990800] spi_mem_exec_op+0x8ec/0xd30
[ 36.994762] spi_mem_no_dirmap_read+0x190/0x1e0
[ 36.999323] spi_mem_dirmap_write+0x238/0x32c
[ 37.003710] spi_nor_write_data+0x220/0x374
[ 37.007932] spi_nor_write+0x110/0x2e8
[ 37.011711] mtd_write_oob_std+0x154/0x1f0
[ 37.015838] mtd_write_oob+0x104/0x1d0
[ 37.019617] mtd_write+0xb8/0x12c
[ 37.022953] mtdchar_write+0x224/0x47c
[ 37.026732] vfs_write+0x1e4/0x8c8
[ 37.030163] ksys_write+0xec/0x1d0
[ 37.033586] __arm64_sys_write+0x6c/0x9c
[ 37.037539] invoke_syscall+0x6c/0x258
[ 37.041327] el0_svc_common.constprop.0+0x160/0x22c
[ 37.046244] do_el0_svc+0x44/0x5c
[ 37.049589] el0_svc+0x38/0x78
[ 37.052681] el0t_64_sync_handler+0x13c/0x158
[ 37.057077] el0t_64_sync+0x190/0x194
[ 37.060775]
[ 37.062274] Allocated by task 455:
[ 37.065701] kasan_save_stack+0x2c/0x54
[ 37.069570] kasan_save_track+0x20/0x3c
[ 37.073438] kasan_save_alloc_info+0x40/0x54
[ 37.077736] __kasan_kmalloc+0xa0/0xb8
[ 37.081515] __kmalloc_noprof+0x158/0x2f8
[ 37.085563] mtd_kmalloc_up_to+0x120/0x154
[ 37.089690] mtdchar_write+0x130/0x47c
[ 37.093469] vfs_write+0x1e4/0x8c8
[ 37.096901] ksys_write+0xec/0x1d0
[ 37.100332] __arm64_sys_write+0x6c/0x9c
[ 37.104287] invoke_syscall+0x6c/0x258
[ 37.108064] el0_svc_common.constprop.0+0x160/0x22c
[ 37.112972] do_el0_svc+0x44/0x5c
[ 37.116319] el0_svc+0x38/0x78
[ 37.119401] el0t_64_sync_handler+0x13c/0x158
[ 37.123788] el0t_64_sync+0x190/0x194
[ 37.127474]
[ 37.128977] The buggy address belongs to the object at ffff00081037c2a0
[ 37.128977] which belongs to the cache kmalloc-8 of size 8
[ 37.141177] The buggy address is located 0 bytes inside of
[ 37.141177] allocated 3-byte region [ffff00081037c2a0, ffff00081037c2a3)
[ 37.153465]
[ 37.154971] The buggy address belongs to the physical page:
[ 37.160559] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x89037c
[ 37.168596] flags: 0xbfffe0000000000(node=0|zone=2|lastcpupid=0x1ffff)
[ 37.175149] page_type: 0xfdffffff(slab)
[ 37.179021] raw: 0bfffe0000000000 ffff000800002500 dead000000000122 0000000000000000
[ 37.186788] raw: 0000000000000000 0000000080800080 00000001fdffffff 0000000000000000
[ 37.194553] page dumped because: kasan: bad access detected
[ 37.200144]
[ 37.201647] Memory state around the buggy address:
[ 37.206460] ffff00081037c180: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
[ 37.213701] ffff00081037c200: fa fc fc fc 05 fc fc fc 03 fc fc fc 02 fc fc fc
[ 37.220946] >ffff00081037c280: 06 fc fc fc 03 fc fc fc fc fc fc fc fc fc fc fc
[ 37.228186] ^
[ 37.232473] ffff00081037c300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.239718] ffff00081037c380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.246962] ==================================================================
[ 37.254394] Disabling lock debugging due to kernel taint
0+1 records in
0+1 records out
3 bytes copied, 0.335911 s, 0.0 kB/s
Fixes: a5356aef6a90 ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Cc: stable@kernel.org
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://patch.msgid.link/20240911211146.3337068-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 730bbfaf7d4890bd99e637db7767dc68cfeb24e7 ]
The effective SPI clock frequency should never exceed speed_hz
otherwise this might result in undefined behavior of the SPI device.
Currently the scldiv calculation could violate this constraint.
For the example parameters perclk_rate = 24 MHz and speed_hz = 7 MHz,
the function fsl_lpspi_set_bitrate will determine perscale = 0 and
scldiv = 1, which is a effective SPI clock of 8 MHz.
So fix this by rounding up the quotient of perclk_rate and speed_hz.
While this never change within the loop, we can pull this out.
Fixes: 5314987de5e5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20240804113611.83613-1-wahrenst@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2fa98705a9289c758b6154a22174aa8d4041a285 ]
- replace the array with the shift operation
- remove the extra comparing operation.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20200220141143.3902922-2-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 730bbfaf7d48 ("spi: spi-fsl-lpspi: Fix scldiv calculation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce1dac560a74220f2e53845ec0723b562288aed4 ]
While in commit 2dd33f9cec90 ("spi: imx: support DMA for imx35") it was
claimed that DMA works on i.MX25, i.MX31 and i.MX35 the respective
device trees don't add DMA channels. The Reference manuals of i.MX31 and
i.MX25 also don't mention the CSPI core being DMA capable. (I didn't
check the others.)
Since commit e267a5b3ec59 ("spi: spi-imx: Use dev_err_probe for failed
DMA channel requests") this results in an error message
spi_imx 43fa4000.spi: error -ENODEV: can't get the TX DMA channel!
during boot. However that isn't fatal and the driver gets loaded just
fine, just without using DMA.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://patch.msgid.link/20240508095610.2146640-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 95d7c452a26564ef0c427f2806761b857106d8c4 ]
The dev_warn to notify about a spurious interrupt was introduced with
the reasoning that these are unexpected. However spurious interrupts
tend to trigger continously and the error message on the serial console
prevents that the core's detection of spurious interrupts kicks in
(which disables the irq) and just floods the console.
Fixes: c64e7efe46b7 ("spi: stm32: make spurious and overrun interrupts visible")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://msgid.link/r/20240521105241.62400-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f788ba457b45b0ce422943fcec9fa35c4587764 ]
There is no need to set the DMA mapped flag of the message if it has
no mapped transfers. Moreover, it may give the code a chance to take
the wrong paths, i.e. to exercise DMA related APIs on unmapped data.
Make __spi_map_msg() to bail earlier on the above mentioned cases.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240522171018.3362521-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a20ad45008a7c82f1184dc6dee280096009ece55 ]
The TX buffer in spi_transfer can be a NULL pointer, so the interrupt
handler may end up writing to the invalid memory and cause crashes.
Add a check to trans->tx_buf before using it.
Fixes: 1ce24864bff4 ("spi: mediatek: Only do dma for 4-byte aligned buffers")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-2-fshao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b2bf6b7faa9010fae10dc7de76627a3fdb525b3 ]
'status' is known to be 0 at this point. The expected error code is
PTR_ERR(clk).
Switch to dev_err_probe() in order to display the expected error code (in a
human readable way).
This also filters -EPROBE_DEFER cases, should it happen.
Fixes: 1ab7f2a43558 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/928f3fb507d53ba0774df27cea0bbba4b055993b.1661599671.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b3aa619a8b4706f35cb62f780c14e68796b37f3f ]
Since commit 24778be20f87 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.
Fixes: 24778be20f87 ("spi: convert drivers to use bits_per_word_mask")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 574bf7bbe83794a902679846770f75a9b7f28176 ]
SFDP read shall use the mspi reads when using the bcm_qspi_exec_mem_op()
call. This fixes SFDP parameter page read failures seen with parts that
now use SFDP protocol to read the basic flash parameter table.
Fixes: 5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://msgid.link/r/20240109210033.43249-1-kamal.dasu@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5c7bcb499840551cfbe85c6df177ebc50432bf0 ]
Documentation says only DTDL of 200 is allowed for this SoC.
Fixes: 4286db8456f4 ("spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://msgid.link/r/20231212081239.14254-1-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2ded280a4b1b7bd93e53670528504be08d24967 ]
Zynq QSPI driver has been converted to use spi-mem framework so
add spi-mem to driver kconfig dependencies.
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1699037031-702858-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2ec8b010979036c2fe79a64adb6ecc0bd11e91d1 ]
We don't want to use the value of ilog2(0) as dummy.buswidth is 0 when
dummy.nbytes is 0. Since we have no dummy bytes, we don't need to
configure the dummy byte bits per clock register value anyway.
Signed-off-by: "William A. Kennington III" <william@wkennington.com>
Link: https://lore.kernel.org/r/20230922182812.2728066-1-william@wkennington.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 18495676f7886e105133f1dc06c1d5e8d5436f32 ]
Reset the FLSHxCR1 registers to default value. ROM may set the register
value and it affects the SPI NAND normal functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20230906183254.235847-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
tegra_sflash_probe()
[ Upstream commit 29a449e765ff70a5bd533be94babb6d36985d096 ]
The platform_get_irq might be failed and return a negative result. So
there should have an error handling code.
Fixed this by adding an error handling code.
Fixes: 8528547bcc33 ("spi: tegra: add spi driver for sflash controller")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_71FC162D589E4788C2152AAC84CD8D5C6D06@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5158814cbb37bbb38344b3ecddc24ba2ed0365f2 ]
The command word is defined as following:
/* Command */
#define SPI_CMD_COMMAND_SHIFT 0
#define SPI_CMD_DEVICE_ID_SHIFT 4
#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
#define SPI_CMD_ONE_BYTE_SHIFT 11
#define SPI_CMD_ONE_WIRE_SHIFT 12
If the prepend byte count field starts at bit 8, and the next defined
bit is SPI_CMD_ONE_BYTE at bit 11, it can be at most 3 bits wide, and
thus the max value is 7, not 15.
Fixes: b17de076062a ("spi/bcm63xx: work around inability to keep CS up")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20230629071453.62024-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c1f23ad34fcdace50275a6aa1e1969b41c6233f ]
If neither a "hif_mspi" nor "mspi" resource is present, the driver will
just early exit in probe but still return success. Apart from not doing
anything meaningful, this would then also lead to a null pointer access
on removal, as platform_get_drvdata() would return NULL, which it would
then try to dereference when trying to unregister the spi master.
Fix this by unconditionally calling devm_ioremap_resource(), as it can
handle a NULL res and will then return a viable ERR_PTR() if we get one.
The "return 0;" was previously a "goto qspi_resource_err;" where then
ret was returned, but since ret was still initialized to 0 at this place
this was a valid conversion in 63c5395bb7a9 ("spi: bcm-qspi: Fix
use-after-free on unbind"). The issue was not introduced by this commit,
only made more obvious.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Link: https://lore.kernel.org/r/20230629134306.95823-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5fd7c99ecf45c8ee8a9b1268f0ffc91cc6271da2 ]
The CS_TOGGLE bit when set is supposed to instruct FW to
toggle CS line between words. The driver with intent of
disabling this behaviour has been unsetting BIT(0). This has
not caused any trouble so far because the original BIT(1)
is untouched and BIT(0) likely wasn't being used.
Correct this to prevent a potential future bug.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org
Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1682412128-1913-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5c31fb71f16ba75bad4ade208abbae225305b65 ]
The DSPI controller has configurable timing for
(a) tCSC: the interval between the assertion of the chip select and the
first clock edge
(b) tASC: the interval between the last clock edge and the deassertion
of the chip select
What is a bit surprising, but is documented in the figure "Example of
continuous transfer (CPHA=1, CONT=1)" in the datasheet, is that when the
chip select stays asserted between multiple TX FIFO writes, the tCSC and
tASC times still apply. With CONT=1, chip select remains asserted, but
SCK takes a break and goes to the idle state for tASC + tCSC ns.
In other words, the default values (of 0 and 0 ns) result in SCK
glitches where the SCK transition to the idle state, as well as the SCK
transition from the idle state, will have no delay in between, and it
may appear that a SCK cycle has simply gone missing. The resulting
timing violation might cause data corruption in many peripherals, as
their chip select is asserted.
The driver has device tree bindings for tCSC ("fsl,spi-cs-sck-delay")
and tASC ("fsl,spi-sck-cs-delay"), but these are only specified to apply
when the chip select toggles in the first place, and this timing
characteristic depends on each peripheral. Many peripherals do not have
explicit timing requirements, so many device trees do not have these
properties present at all.
Nonetheless, the lack of SCK glitches is a common sense requirement, and
since the SCK stays in the idle state during transfers for tCSC+tASC ns,
and that in itself should look like half a cycle, then let's ensure that
tCSC and tASC are at least a quarter of a SCK period, such that their
sum is at least half of one.
Fixes: 95bf15f38641 ("spi: fsl-dspi: Add ~50ns delay between cs and sck")
Reported-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Debugged-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Tested-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230529223402.1199503-1-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d6af5796e5d9a88ae83c9c753023bba61deb18b ]
This variable has been present since the initial submission of the
driver, and held, for some reason, the value of zero, to be sent on the
wire in the case there wasn't any TX buffer for the current transfer.
Since quite a while now, however, it isn't doing anything at all.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: c5c31fb71f16 ("spi: fsl-dspi: avoid SCK glitches with continuous transfers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c331fd1dccfba657129380ee084b95c1cedfbef ]
It is usually better to request all necessary resources (clocks,
regulators, ...) before starting to make use of them. That way they do
not change state in case one of the resources is not available yet and
probe deferral (-EPROBE_DEFER) is necessary. This is particularly
important for DMA channels and IOMMUs which are not enforced by
fw_devlink yet (unless you use fw_devlink.strict=1).
spi-qup does this in the wrong order, the clocks are enabled and
disabled again when the DMA channels are not available yet.
This causes issues in some cases: On most SoCs one of the SPI QUP
clocks is shared with the UART controller. When using earlycon UART is
actively used during boot but might not have probed yet, usually for
the same reason (waiting for the DMA controller). In this case, the
brief enable/disable cycle ends up gating the clock and further UART
console output will halt the system completely.
Avoid this by requesting the DMA channels before changing the clock
state.
Fixes: 612762e82ae6 ("spi: qup: Add DMA capabilities")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230518-spi-qup-clk-defer-v1-1-f49fc9ca4e02@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 87c614175bbf28d3fd076dc2d166bac759e41427 ]
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20230318222132.3373-1-kgroeneveld@lenbrook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c20c57d9868d7f9fd1b2904c7801b07e128f6322 ]
CPM has the same problem as QE so for CPM also use the fix added
by commit 0398fb70940e ("spi/spi_mpc8xxx: Fix QE mode Litte Endian"):
CPM mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for 16 and 32 bits
words. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also limit the workaround to 16 and 32 bits words because it can
only work for multiples of 8-bits.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 0398fb70940e ("spi/spi_mpc8xxx: Fix QE mode Litte Endian")
Link: https://lore.kernel.org/r/1b7d3e84b1128f42c1887dd2fb9cdf390f541bc1.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 61f49171a43ab1f80c73c5c88c508770c461e0f2 ]
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
Fixes: 64ff247a978f ("spi: Add Qualcomm QUP SPI controller support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230330210341.2459548-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e6a0b671880207566e1ece983bf989dde60bc1d7 ]
wait_for_completion_timeout() never returns a <0 value. It returns either
on timeout or a positive value (at least 1, or number of jiffies left
till timeout)
So, fix the error handling path and return -ETIMEDOUT should a timeout
occur.
Fixes: b0823ee35cf9 ("spi: Add spi driver for Socionext SynQuacer platform")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/c2040bf3cfa201fd8890cfab14fa5a701ffeca14.1676466072.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 811ff802aaf878ebbbaeac0307a0164fa21e7d40 ]
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
Fixes: 142168eba9dc ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-11-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
