| Age | Commit message (Collapse) | Author |
|---|
|
Driver received a SCSI completion after it posted the cleanup request. This
leads to a problem that one ref count wasn't released leading to
flush_active_ios to get struck. The callback from libfc never returned and
other ports were not processed leading to APD.
Decrease the refcnt as well as try to complete if something is waiting for
completion.
Link: https://lore.kernel.org/r/20200327054849.15947-3-skashyap@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Filesystem goes to read-only after continuous error injection because RQE
was handled in deferred context, leading to mismatch between CQE and RQE.
Specifically, this patch makes the following changes:
- Process the RQE with CQE in interrupt context, before putting it into
the work queue.
- Producer and consumer indices are also updated in the interrupt context
to guarantee the the order of processing.
[mkp: fixed bad indentation]
Link: https://lore.kernel.org/r/20200327054849.15947-2-skashyap@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Once fail happens during suspend and resume flow if the desired low power
link state is H8, link recovery is required for MediaTek UFS controller.
For resume flow, since power and clocks are already enabled before invoking
vendor's resume callback, simply using ufshcd_link_recovery() inside
callback is fine.
For suspend flow, the device power enters low power mode or is disabled
before suspend callback, thus ufshcd_link_recovery() can not be directly
used in vendor callback. One solution is to set the link to off state and
then ufshcd_host_reset_and_restore() will be executed by ufshcd_suspend().
Link: https://lore.kernel.org/r/20200327095329.10083-3-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Export ufshcd_link_recovery to allow vendors to recover failed link in
vendor's callbacks.
Link: https://lore.kernel.org/r/20200327095329.10083-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This change introduces a func ufshcd_set_clk_freq() to explicitly set clock
frequency so that it can be used in reset_and_restore path and in
ufshcd_scale_clks(). This change also cleans up the clock scaling error out
path.
[mkp: commit desc]
Link: https://lore.kernel.org/r/1585214742-5466-2-git-send-email-cang@codeaurora.org
Fixes: a3cd5ec55f6c ("scsi: ufs: add load based scaling of UFS gear")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update lpfc version to 12.8.0.0
Link: https://lore.kernel.org/r/20200322181304.37655-13-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During code review, identified dss feature that was a prototype only and
was never productized in SLI3. They shouldn't be there and prevents reuse
of the command areas.
Remove any code in the driver to deal with dss, including code to deal with
fips, which is associated with the dss feature.
Link: https://lore.kernel.org/r/20200322181304.37655-12-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently driver ktime stats, measuring code paths, is NVME-specific.
Convert the stats routines such that the code paths are generic, providing
status for NVME and SCSI. Added ktime stat calls in SCSI queuecommand and
cmpl routines.
Link: https://lore.kernel.org/r/20200322181304.37655-11-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The cpu io statistics were capped by a hard define limit of 128. This
effectively was a max number of CPUs, not an actual CPU count, nor actual
CPU numbers which can be even larger than both of those values. This made
stats off/misleading and on large CPU count systems, wrong.
Fix the stats so that all CPUs can have a stats struct. Fix the looping
such that it loops by hdwq, finds CPUs that used the hdwq, and sum the
stats, then display.
Link: https://lore.kernel.org/r/20200322181304.37655-9-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Kernel is crashing with the following stacktrace:
BUG: unable to handle kernel NULL pointer dereference at
00000000000005bc
IP: lpfc_nvme_register_port+0x1a8/0x3a0 [lpfc]
...
Call Trace:
lpfc_nlp_state_cleanup+0x2b2/0x500 [lpfc]
lpfc_nlp_set_state+0xd7/0x1a0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x1f7/0x450 [lpfc]
lpfc_disc_state_machine+0x7a/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x16f/0x1e0 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x5b2/0x690 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x182/0x230 [lpfc]
lpfc_do_work+0x87f/0x1570 [lpfc]
kthread+0x10d/0x130
ret_from_fork+0x35/0x40
During target side fault injections, it is possible to hit the
NLP_WAIT_FOR_UNREG case in lpfc_nvme_remoteport_delete. A prior commit
fixed a rebind and delete race condition, but called lpfc_nlp_put
unconditionally. This triggered a deletion and the crash.
Fix by movng nlp_put to inside the NLP_WAIT_FOR_UNREG case, where the nlp
will be being unregistered/removed. Leave the reference if the flag isn't
set.
Link: https://lore.kernel.org/r/20200322181304.37655-8-jsmart2021@gmail.com
Fixes: b15bd3e6212e ("scsi: lpfc: Fix nvme remoteport registration race conditions")
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The lpfc_sli4_wq_release() routine iterates for each interim value when
updating the wq consuemr index. This wastes cycles and possibly confuses
things as thevalue itterates (and the modulo logic is being applied).
There's no reason for this. Just set it to the value from the hw.
Link: https://lore.kernel.org/r/20200322181304.37655-7-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Injecting EEH on a 32GB card is causing kernel oops
The pci error handler is doing an IO flush and the offline code is also
doing an IO flush. When the 1st flush is complete the hdwq is destroyed
(freed), yet the second flush accesses the hdwq and crashes.
Added a check in lpfc_sli4_fush_io_rings to check both the HBA_IOQ_FLUSH
flag and the hdwq pointer to see if it is already set and not already
freed.
Link: https://lore.kernel.org/r/20200322181304.37655-6-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SCSI layer sends driver IOs with more s/g segments than driver can handle.
This results in "Too many sg segments from dma_map_sg. Config 64, seg_cnt
219" error messages from the lpfc_scsi_prep_dma_buf_s3() routine.
The was due to use the driver using individual templates for pport and
vport, host reset enabled or not, nvme vs scsi, etc. In the end, there was
a combination for a vport that didn't match the pport.
Rather than enumerating more templates and more discretionary assignments,
revert to a base template that is copied to a template specific to the
pport/vport. Then, based on role, attributes and sli type, modify the
fields that are different for that port. Added a log message to
lpfc_create_port to validate values.
Link: https://lore.kernel.org/r/20200322181304.37655-5-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In lpfc_nvmet_prep_fcp_wqe() the line "rsp->sg_cnt = 0" is modifying the
transport's data structure. This may result in the transport believing the
s/g list was already freed, thus may not unmap/free it properly. Lpfc
driver should not modify the transport data structure.
The zeroing of the sg_cnt is to avoid use of the transport's sgl in a
subsequent loop where the driver builds the necessary requests for the
adapter firmware to complete the IO.
Change LLDD to use a local copy of the transport sg_cnt when building
requests to be passed to the adapter fw.
Link: https://lore.kernel.org/r/20200322181304.37655-4-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following lockdep error was reported when unloading the lpfc driver:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Call Trace:
dump_stack+0x96/0xe0
register_lock_class+0x8b8/0x8c0
? lockdep_hardirqs_on+0x190/0x280
? is_dynamic_key+0x150/0x150
? wait_for_completion_interruptible+0x2a0/0x2a0
? wake_up_q+0xd0/0xd0
__lock_acquire+0xda/0x21a0
? register_lock_class+0x8c0/0x8c0
? synchronize_rcu_expedited+0x500/0x500
? __call_rcu+0x850/0x850
lock_acquire+0xf3/0x1f0
? del_timer_sync+0x5/0xb0
del_timer_sync+0x3c/0xb0
? del_timer_sync+0x5/0xb0
lpfc_pci_remove_one.cold.102+0x8b7/0x935 [lpfc]
...
Unloading the driver resulted in a call to del_timer_sync for the
cpuhp_poll_timer. However the call to setup the timer had never been made,
so the timer structures used by lockdep checking were not initialized.
Unconditionally call setup_timer for the cpuhp_poll_timer during driver
initialization. Calls to start the timer remain "as needed".
Link: https://lore.kernel.org/r/20200322181304.37655-3-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following kasan bug was called out:
BUG: KASAN: slab-out-of-bounds in lpfc_unreg_login+0x7c/0xc0 [lpfc]
Read of size 2 at addr ffff889fc7c50a22 by task lpfc_worker_3/6676
...
Call Trace:
dump_stack+0x96/0xe0
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
print_address_description.constprop.6+0x1b/0x220
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
__kasan_report.cold.9+0x37/0x7c
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
kasan_report+0xe/0x20
lpfc_unreg_login+0x7c/0xc0 [lpfc]
lpfc_sli_def_mbox_cmpl+0x334/0x430 [lpfc]
...
When processing the completion of a "Reg Rpi" login mailbox command in
lpfc_sli_def_mbox_cmpl, a call may be made to lpfc_unreg_login. The vpi is
extracted from the completing mailbox context and passed as an input for
the next. However, the vpi stored in the mailbox command context is an
absolute vpi, which for SLI4 represents both base + offset. When used with
a non-zero base component, (function id > 0) this results in an
out-of-range access beyond the allocated phba->vpi_ids array.
Fix by subtracting the function's base value to get an accurate vpi number.
Link: https://lore.kernel.org/r/20200322181304.37655-2-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The file aic79xx_core.c still contains some FreeBSD-specific code/macro
guards, although cross-compatibility was in theory removed with commit
cca6cb8ad7a8 ("scsi: aic7xxx: Fix build using bare-metal toolchain").
Remove it.
Link: https://lore.kernel.org/r/20200326193817.12568-1-alex.dewar@gmx.co.uk
Signed-off-by: Alex Dewar <alex.dewar@gmx.co.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We were setting bActiveICCLevel attribute for UFS device only once but the
type of this attribute has changed from persistent to volatile since UFS
device specification v2.1. This attribute is set to the default value after
power cycle or hardware reset event. It isn't safe to rely on prefetched
data (only used for bActiveICCLevel attribute now). Hence this change
removes the code related to data prefetching and set this parameter on
every attempt to probe the UFS device.
Tested-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
dc395x_bios_param was only different from the default when the
CONFIG_SCSI_DC395x_TRMS1040_TRADMAP symbol is true, but that symbol doesn't
exist in the Kconfig system and thus can't be set.
Link: https://lore.kernel.org/r/20200325105505.1028582-1-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix an error count for active session if the total_cmds is invalid on the
function iscsi_session_setup(). Decrement the number of active sessions
before the funcion return.
Link: https://lore.kernel.org/r/EDBAAA0BBBA2AC4E9C8B6B81DEEE1D6916A28542@DGGEML525-MBS.china.huawei.com
Reviewed-by: Lee Duncan <lduncan@suuse.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct race condition where ioaccel is re-enabled before the raid_map is
updated. For RAID_1, RAID_1ADM, and RAID 5/6 there is a BUG_ON called which
is bad.
- Change event thread to disable ioaccel only. Send all requests down the
RAID path instead.
- Have rescan thread handle offload_enable.
- Since there is only one rescan allowed at a time, turning
offload_enabled on/off should not be racy. Each handler queues up a
rescan if one is already in progress.
- For timing diagram, offload_enabled is initially off due to a change
(transformation: splitmirror/remirror), ...
otbe = offload_to_be_enabled
oe = offload_enabled
Time Event Rescan Completion Request
Worker Worker Thread Thread
---- ------ ------ ---------- -------
T0 | | + UA |
T1 | + rescan started | 0x3f |
T2 + Event | | 0x0e |
T3 + Ack msg | | |
T4 | + if (!dev[i]->oe && | |
T5 | | dev[i]->otbe) | |
T6 | | get_raid_map | |
T7 + otbe = 1 | | |
T8 | | | |
T9 | + oe = otbe | |
T10 | | | + ioaccel request
T11 * BUG_ON
T0 - I/O completion with UA 0x3f 0x0e sets rescan flag.
T1 - rescan worker thread starts a rescan.
T2 - event comes in
T3 - event thread starts and issues "Acknowledge" message
...
T6 - rescan thread has bypassed code to reload new raid map.
...
T7 - event thread runs and sets offload_to_be_enabled
...
T9 - rescan thread turns on offload_enabled.
T10- request comes in and goes down ioaccel path.
T11- BUG_ON.
- After the patch is applied, ioaccel_enabled can only be re-enabled in
the re-scan thread.
Link: https://lore.kernel.org/r/158472877894.14200.7077843399036368335.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Matt Perricone <matt.perricone@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add PCI shutdown handler support for supporting wake-on-lan feature.
Link: https://lore.kernel.org/r/20200319083811.19499-3-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch adds the mfw error recovery process in the qedi driver. The
process includes a partial/customized driver unload and load to reset
context by preserving active iSCSI session kernel state.
Link: https://lore.kernel.org/r/20200319083811.19499-2-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Block layer RPM is enabled for the genernal UFS SCSI devices when they are
probed by their driver. However block layer RPM is not enabled for UFS
well-known SCSI devices.
As UFS SCSI devices have their corresponding BSG char devices, accessing a
BSG char device via IOCTL may send requests to its corresponding SCSI
device through its request queue. If BSG IOCTL sends a request to a
well-known SCSI device when HBA is not runtime active, due to block layer
RPM not being enabled for the well-known SCSI devices, the HBA, which is at
the top of a SCSI device's parent chain, will not be resumed.
This change enables block layer RPM for the well-known SCSI devices so that
block layer can handle RPM for the well-known SCSI devices just like for
the general SCSI devices.
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Override devfreq parameters for power-performance trade-off.
Link: https://lore.kernel.org/r/b6875729b6072134985c9113a820cf60a2af22e7.1585160616.git.asutoshd@codeaurora.org
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Vendor drivers may have a need to update the polling interval and
thresholds. Provide a vops for vendor drivers to use.
Link: https://lore.kernel.org/r/acd79e00396cff855256adad47f615ccdbde85ac.1585160616.git.asutoshd@codeaurora.org
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, the frequency that devfreq provides the driver always leads the
clocks to be scaled up. Hence, round the clock-rate to the nearest
frequency before deciding to scale.
Also update the devfreq statistics of current frequency.
Link: https://lore.kernel.org/r/d0c6c22455811e9f0eda01f9bc70d1398b51b2bd.1585160616.git.asutoshd@codeaurora.org
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As a part of sysfs reading of descriptors/attributes/flags, query commands
should only be executed when hba's power runtime status is active. To
guarantee this, add pm_runtime_get/put_sync() to those paths where query
commands are sent.
Link: https://lore.kernel.org/r/f712a4f7bdb0ae32e0d83634731e7aaa1b3a6cdd.1585009663.git.asutoshd@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Nitin Rawat <nitirawa@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
MediaTek platform and UFS controller can dynamically customize the delay
for host enabling according to different scenarios.
For example, if UniPro enters lower-power mode, such delay can be
minimized, otherwise longer delay shall be expected.
Link: https://lore.kernel.org/r/20200318104016.28049-8-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reduce the waiting period between each HCE (Host Controller Enable) polling
from 5 ms to 1 ms. Also increase the maximum polling times to make "total
polling time" roughly the same.
This change could make HCE initialization faster to improve latency of
ufshcd initialization, error recovery, and resume behaviors.
Link: https://lore.kernel.org/r/20200318104016.28049-7-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently a 1 ms delay is applied before polling CONTROLLER_ENABLE
bit. This delay may not be required or can be changed in different
controllers. Make the delay as a changeable value in struct ufs_hba to
allow it customized by vendors.
Link: https://lore.kernel.org/r/20200318104016.28049-6-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A common delay function is introduced in UFS core driver, thus ufs-mediatek
can use it instead of the private delay function.
Link: https://lore.kernel.org/r/20200318104016.28049-5-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Introduce a common delay function to provide flexible way for users to take
choices of udelay and usleep_range into consideration according to the
required delay time.
Link: https://lore.kernel.org/r/20200318104016.28049-4-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use an enum to specify the host capabilities instead of #defines inside the
structure definition.
Link: https://lore.kernel.org/r/20200318104016.28049-3-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In ufshcd_disable_tx_lcc(), if ufshcd_dme_get() or ufshcd_dme_peer_get()
get fail, uninitialized variable "tx_lanes" may be used as unexpected lane
ID for DME configuration.
Fix this issue by initializing "tx_lanes".
Link: https://lore.kernel.org/r/20200318104016.28049-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If an iSCSI connection happens to fail while the daemon isn't running (due
to a crash or for another reason), the kernel failure report is not
received. When the daemon restarts, there is insufficient kernel state in
sysfs for it to know that this happened. open-iscsi tries to reopen every
connection, but on different initiators, we'd like to know which
connections have failed.
There is session->state, but that has a different lifetime than an iSCSI
connection, so it doesn't directly reflect the connection state.
[mkp: typos]
Link: https://lore.kernel.org/r/20200317233422.532961-1-krisman@collabora.com
Cc: Khazhismel Kumykov <khazhy@google.com>
Suggested-by: Junho Ryu <jayr@google.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If 'dma_map_single()' fails, the ref counted 'shpnt' will be decremented
twice because 'scsi_host_put()' is called in the if block, and in the error
handling path.
Axe one of these calls.
Link: https://lore.kernel.org/r/20200228215948.7473-1-christophe.jaillet@wanadoo.fr
Fixes: 1dc09e120c83 ("scsi: aha1740: stop using scsi_unregister")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove code which has no functional use anymore since commit 3c75ad1d87c7
("scsi: qla2xxx: Remove defer flag to indicate immeadiate port loss").
While at it remove also the stale function documentation.
Link: https://lore.kernel.org/r/20200206135443.110701-1-dwagner@suse.de
Reviewed-by: Arun Easi <aeasi@marvell.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no reason to expose SATA_PMP config option when no SATA
host drivers are enabled. To fix it add SATA_HOST config option,
make all SATA host drivers select it and finally make SATA_PMP
config options depend on it.
This also serves as preparation for the future changes which
optimize libata core code size on PATA only setups.
CC: "James E.J. Bottomley" <jejb@linux.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # for SCSI bits
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SPDX License Identifier to all .gitignore files.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some USB bridge devices will return a default set of characteristics during
initialization. And then, once an attached drive has spun up, substitute
the actual parameters reported by the drive. According to the SCSI spec,
the device should return a UNIT ATTENTION in case any reported parameters
change. But in this case the change is made silently after a small window
where default values are reported.
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of
physical block size") validated the reported optimal I/O size against the
physical block size to overcome problems with devices reporting nonsensical
transfer sizes. However, this validation did not account for the fact that
aforementioned devices will return default values during a brief window
during spin-up. The subsequent change in reported characteristics would
invalidate the checking that had previously been performed.
Unset a previously configured optimal I/O size should the sanity checking
fail on subsequent revalidate attempts.
Link: https://lore.kernel.org/r/33fb522e-4f61-1b76-914f-c9e6a3553c9b@gmail.com
Cc: Bryan Gurney <bgurney@redhat.com>
Cc: <stable@vger.kernel.org>
Reported-by: Bernhard Sulzer <micraft.b@gmail.com>
Tested-by: Bernhard Sulzer <micraft.b@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
struct partition is the on-disk format of a MSDOS partition table entry.
Move it out of genhd.h into a new msdos_partition.h header and give it
a msdos_ prefix to avoid confusion.
Also move the magic number from block/partitions/msdos.h to the new
header so that it can be used by the SCSI drivers looking at the DOS
partition tables.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Call scsi_bios_ptable from scsi_partsize instead of requiring boilerplate
code in the callers. Also switch the calling convention to match that
of the ->bios_param instances calling this function, and use true/false
for the return value instead of the weird -1 convention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This avoids the need for a forward declaration and generally keeps the
file in the lower level first, high level last order.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Use read_mapping_page and kmemdup instead of the odd read_dev_sector and
put_dev_sector helpers from the partitioning code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
block/genhd provides set_capacity_revalidate_and_notify() for sending RESIZE
notifications via uevents. This notification is newly added to scsi sd.
Signed-off-by: Balbir Singh <sblbir@amazon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Removed the common length and introduce read and write length for IOCTL
payload structure.
[mkp: fixed SoB ordering]
Link: https://lore.kernel.org/r/20200316074906.9119-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <viswas.g@microchip.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Added the sysfs attribute for non fatal log so that management utility can
get the non fatal dump from driver. The non-fatal error is an error
condition or abnormal behavior detected by the host, or detected and
reported by the controller to the host.The non-fatal error does not stop
the controller firmware and enables it to still respond to host requests.
A typical example of a non-fatal error is an I/O timeout or an unusual
error notification from the controller. Since the firmware is operational,
the error dump information is pushed to host memory (by firmware) upon
request from the host.
Link: https://lore.kernel.org/r/20200316074906.9119-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
