| Age | Commit message (Collapse) | Author |
|---|
|
Three driver callbacks schedule a reset and wait for its completion:
ndo_change_mtu(), ethtool set_ringparam(), and ethtool set_channels().
Waiting for reset in ndo_change_mtu() and set_ringparam() was added by
commit c2ed2403f12c ("iavf: Wait for reset in callbacks which trigger
it") to fix a race condition where adding an interface to bonding
immediately after MTU or ring parameter change failed because the
interface was still in __RESETTING state. The same commit also added
waiting in iavf_set_priv_flags(), which was later removed by commit
53844673d555 ("iavf: kill "legacy-rx" for good").
Waiting in set_channels() was introduced earlier by commit 4e5e6b5d9d13
("iavf: Fix return of set the new channel count") to ensure the PF has
enough time to complete the VF reset when changing channel count, and to
return correct error codes to userspace.
Commit ef490bbb2267 ("iavf: Add net_shaper_ops support") added
net_shaper_ops to iavf, which required reset_task to use _locked NAPI
variants (napi_enable_locked, napi_disable_locked) that need the netdev
instance lock.
Later, commit 7e4d784f5810 ("net: hold netdev instance lock during
rtnetlink operations") and commit 2bcf4772e45a ("net: ethtool: try to
protect all callback with netdev instance lock") started holding the
netdev instance lock during ndo and ethtool callbacks for drivers with
net_shaper_ops.
Finally, commit 120f28a6f314 ("iavf: get rid of the crit lock")
replaced the driver's crit_lock with netdev_lock in reset_task, causing
incorrect behavior: the callback holds netdev_lock and waits for
reset_task, but reset_task needs the same lock:
Thread 1 (callback) Thread 2 (reset_task)
------------------- ---------------------
netdev_lock() [blocked on workqueue]
ndo_change_mtu() or ethtool op
iavf_schedule_reset()
iavf_wait_for_reset() iavf_reset_task()
waiting... netdev_lock() <- blocked
This does not strictly deadlock because iavf_wait_for_reset() uses
wait_event_interruptible_timeout() with a 5-second timeout. The wait
eventually times out, the callback returns an error to userspace, and
after the lock is released reset_task completes the reset. This leads to
incorrect behavior: userspace sees an error even though the configuration
change silently takes effect after the timeout.
Fix this by extracting the reset logic from iavf_reset_task() into a new
iavf_reset_step() function that expects netdev_lock to be already held.
The three callbacks now call iavf_reset_step() directly instead of
scheduling the work and waiting, performing the reset synchronously in
the caller's context which already holds netdev_lock. This eliminates
both the incorrect error reporting and the need for
iavf_wait_for_reset(), which is removed along with the now-unused
reset_waitqueue.
The workqueue-based iavf_reset_task() becomes a thin wrapper that
acquires netdev_lock and calls iavf_reset_step(), preserving its use
for PF-initiated resets.
The callbacks may block for several seconds while iavf_reset_step()
polls hardware registers, but this is acceptable since netdev_lock is a
per-device mutex and only serializes operations on the same interface.
v3:
- Remove netif_running() guard from iavf_set_channels(). Unlike
set_ringparam where descriptor counts are picked up by iavf_open()
directly, num_req_queues is only consumed during
iavf_reinit_interrupt_scheme() in the reset path. Skipping the reset
on a down device would silently discard the channel count change.
- Remove dead reset_waitqueue code (struct field, init, and all
wake_up calls) since iavf_wait_for_reset() was the only consumer.
Fixes: 120f28a6f314 ("iavf: get rid of the crit lock")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 7c01dbfc8a1c5f ("iavf: periodically cache PHC time") introduced a
worker to cache PHC time, but failed to stop it during reset or disable.
This creates a race condition where `iavf_reset_task()` or
`iavf_disable_vf()` free adapter resources (AQ) while the worker is still
running. If the worker triggers `iavf_queue_ptp_cmd()` during teardown, it
accesses freed memory/locks, leading to a crash.
Fix this by calling `iavf_ptp_release()` before tearing down the adapter.
This ensures `ptp_clock_unregister()` synchronously cancels the worker and
cleans up the chardev before the backing resources are destroyed.
Fixes: 7c01dbfc8a1c5f ("iavf: periodically cache PHC time")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If CONFIG_IRDMA isn't enabled but there are ice NICs in the system, the
driver will prevent full devlink dev param show dump because its rdma get
callbacks return ENODEV and stop the dump. For example:
$ devlink dev param show
pci/0000:82:00.0:
name msix_vec_per_pf_max type generic
values:
cmode driverinit value 2
name msix_vec_per_pf_min type generic
values:
cmode driverinit value 2
kernel answers: No such device
Returning EOPNOTSUPP allows the dump to continue so we can see all devices'
devlink parameters.
Fixes: c24a65b6a27c ("iidc/ice/irdma: Update IDC to support multiple consumers")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
commit f93505f35745 ("amd-xgbe: let the MAC manage PHY PM") moved
xgbe_phy_reset() from xgbe_open() to xgbe_start(), placing it after
phy_start(). As a result, the PHY settings were being reset after the
PHY had already started.
Reorder the calls so that the PHY settings are reset before
phy_start() is invoked.
Fixes: f93505f35745 ("amd-xgbe: let the MAC manage PHY PM")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-4-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When operating in 10GBASE-KR mode with auto-negotiation disabled and RX
adaptation enabled, CRC errors can occur during the RX adaptation
process. This happens because the driver continues transmitting and
receiving packets while adaptation is in progress.
Fix this by stopping TX/RX immediately when the link goes down and RX
adaptation needs to be re-triggered, and only re-enabling TX/RX after
adaptation completes and the link is confirmed up. Introduce a flag to
track whether TX/RX was disabled for adaptation so it can be restored
correctly.
This prevents packets from being transmitted or received during the RX
adaptation window and avoids CRC errors from corrupted frames.
The flag tracking the data path state is synchronized with hardware
state in xgbe_start() to prevent stale state after device restarts.
This ensures that after a restart cycle (where xgbe_stop disables
TX/RX and xgbe_start re-enables them), the flag correctly reflects
that the data path is active.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-3-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The link status bit is latched low to allow detection of momentary
link drops. If the status indicates that the link is already down,
read it again to obtain the current state.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-2-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Given that some platforms may use PHY address 0 (I suppose the PHY may
not treat address 0 as a broadcast address or default response address).
It is possible for some boards to connect multiple PHYs to the same
ENETC MAC, for example:
- a PHY with a non-zero address connects to ENETC MAC through SGMII
interface (selected via DTS_A)
- a PHY with address 0 connects to ENETC MAC through RGMII interface
(selected via DTS_B)
For the case where the ENETC port MDIO is used to manage the PHY, when
switching from DTS_A to DTS_B via soft reboot, LaBCR[MDIO_PHYAD_PRTAD]
must be updated to 0 because the NETCMIX block is not reset during soft
reboot. However, the current driver explicitly skips configuring address
0, causing LaBCR[MDIO_PHYAD_PRTAD] to retain its old value.
Therefore, remove the special-case skip of PHY address 0 so that valid
configurations using address 0 are properly supported.
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Fixes: 50bfd9c06f0f ("net: enetc: set external PHY address in IERB for i.MX94 ENETC")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The current netc_get_phy_addr() implementation falls back to PHY address
0 when the "mdio" node or the PHY child node is missing. On i.MX95, this
causes failures when a real PHY is actually assigned address 0 and is
managed through the EMDIO interface. Because the bit 0 of phy_mask will
be set, leading imx95_enetc_mdio_phyaddr_config() to return an error, and
the netc_blk_ctrl driver probe subsequently fails. Fix this by returning
-ENODEV when neither an "mdio" node nor any PHY node is present, it means
that ENETC port MDIO is not used to manage the PHY, so there is no need
to configure LaBCR[MDIO_PHYAD_PRTAD].
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Closes: https://lore.kernel.org/all/7825188.GXAFRqVoOG@steina-w
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When changing channels, the current check in bnxt_set_channels()
is not checking for non-default RSS contexts when the RSS table size
changes. The current check for IFF_RXFH_CONFIGURED is only sufficient
for the default RSS context. Expand the check to include the presence
of any non-default RSS contexts.
Allowing such change will result in incorrect configuration of the
context's RSS table when the table size changes.
Fixes: b3d0083caf9a ("bnxt_en: Support RSS contexts in ethtool .{get|set}_rxfh()")
Reported-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/netdev/20260303181535.2671734-1-bjorn@kernel.org/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260306225854.3575672-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DMA mappings were leaked on mapping error. Free them with the
existing emac_free_tx_buf() function.
Fixes: bfec6d7f2001 ("net: spacemit: Add K1 Ethernet MAC")
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Link: https://patch.msgid.link/20260305-k1-ethernet-more-fixes-v2-2-e4e434d65055@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Even if we get a dma_mapping_error() while mapping an RX buffer, we
should still update rx_ring->head to ensure that the buffers we were
able to allocate and map are used. Fix this by breaking out to the
existing code after the loop, analogous to the existing handling for skb
allocation failure.
Fixes: bfec6d7f2001 ("net: spacemit: Add K1 Ethernet MAC")
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Link: https://patch.msgid.link/20260305-k1-ethernet-more-fixes-v2-1-e4e434d65055@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XDP multi-buf programs can modify the layout of the XDP buffer when the
program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The
referenced commit in the fixes tag corrected the assumption in the mlx5
driver that the XDP buffer layout doesn't change during a program
execution. However, this fix introduced another issue: the dropped
fragments still need to be counted on the driver side to avoid page
fragment reference counting issues.
Such issue can be observed with the
test_xdp_native_adjst_tail_shrnk_data selftest when using a payload of
3600 and shrinking by 256 bytes (an upcoming selftest patch): the last
fragment gets released by the XDP code but doesn't get tracked by the
driver. This results in a negative pp_ref_count during page release and
the following splat:
WARNING: include/net/page_pool/helpers.h:297 at mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core], CPU#12: ip/3137
Modules linked in: [...]
CPU: 12 UID: 0 PID: 3137 Comm: ip Not tainted 6.19.0-rc3+ #12 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core]
[...]
Call Trace:
<TASK>
mlx5e_dealloc_rx_wqe+0xcb/0x1a0 [mlx5_core]
mlx5e_free_rx_descs+0x7f/0x110 [mlx5_core]
mlx5e_close_rq+0x50/0x60 [mlx5_core]
mlx5e_close_queues+0x36/0x2c0 [mlx5_core]
mlx5e_close_channel+0x1c/0x50 [mlx5_core]
mlx5e_close_channels+0x45/0x80 [mlx5_core]
mlx5e_safe_switch_params+0x1a5/0x230 [mlx5_core]
mlx5e_change_mtu+0xf3/0x2f0 [mlx5_core]
netif_set_mtu_ext+0xf1/0x230
do_setlink.isra.0+0x219/0x1180
rtnl_newlink+0x79f/0xb60
rtnetlink_rcv_msg+0x213/0x3a0
netlink_rcv_skb+0x48/0xf0
netlink_unicast+0x24a/0x350
netlink_sendmsg+0x1ee/0x410
__sock_sendmsg+0x38/0x60
____sys_sendmsg+0x232/0x280
___sys_sendmsg+0x78/0xb0
__sys_sendmsg+0x5f/0xb0
[...]
do_syscall_64+0x57/0xc50
This patch fixes the issue by doing page frag counting on all the
original XDP buffer fragments for all relevant XDP actions (XDP_TX ,
XDP_REDIRECT and XDP_PASS). This is basically reverting to the original
counting before the commit in the fixes tag.
As frag_page is still pointing to the original tail, the nr_frags
parameter to xdp_update_skb_frags_info() needs to be calculated
in a different way to reflect the new nr_frags.
Fixes: afd5ba577c10 ("net/mlx5e: RX, Fix generating skb from non-linear xdp_buff for legacy RQ")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Amery Hung <ameryhung@gmail.com>
Link: https://patch.msgid.link/20260305142634.1813208-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XDP multi-buf programs can modify the layout of the XDP buffer when the
program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The
referenced commit in the fixes tag corrected the assumption in the mlx5
driver that the XDP buffer layout doesn't change during a program
execution. However, this fix introduced another issue: the dropped
fragments still need to be counted on the driver side to avoid page
fragment reference counting issues.
The issue was discovered by the drivers/net/xdp.py selftest,
more specifically the test_xdp_native_tx_mb:
- The mlx5 driver allocates a page_pool page and initializes it with
a frag counter of 64 (pp_ref_count=64) and the internal frag counter
to 0.
- The test sends one packet with no payload.
- On RX (mlx5e_skb_from_cqe_mpwrq_nonlinear()), mlx5 configures the XDP
buffer with the packet data starting in the first fragment which is the
page mentioned above.
- The XDP program runs and calls bpf_xdp_pull_data() which moves the
header into the linear part of the XDP buffer. As the packet doesn't
contain more data, the program drops the tail fragment since it no
longer contains any payload (pp_ref_count=63).
- mlx5 device skips counting this fragment. Internal frag counter
remains 0.
- mlx5 releases all 64 fragments of the page but page pp_ref_count is
63 => negative reference counting error.
Resulting splat during the test:
WARNING: CPU: 0 PID: 188225 at ./include/net/page_pool/helpers.h:297 mlx5e_page_release_fragmented.isra.0+0xbd/0xe0 [mlx5_core]
Modules linked in: [...]
CPU: 0 UID: 0 PID: 188225 Comm: ip Not tainted 6.18.0-rc7_for_upstream_min_debug_2025_12_08_11_44 #1 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5e_page_release_fragmented.isra.0+0xbd/0xe0 [mlx5_core]
[...]
Call Trace:
<TASK>
mlx5e_free_rx_mpwqe+0x20a/0x250 [mlx5_core]
mlx5e_dealloc_rx_mpwqe+0x37/0xb0 [mlx5_core]
mlx5e_free_rx_descs+0x11a/0x170 [mlx5_core]
mlx5e_close_rq+0x78/0xa0 [mlx5_core]
mlx5e_close_queues+0x46/0x2a0 [mlx5_core]
mlx5e_close_channel+0x24/0x90 [mlx5_core]
mlx5e_close_channels+0x5d/0xf0 [mlx5_core]
mlx5e_safe_switch_params+0x2ec/0x380 [mlx5_core]
mlx5e_change_mtu+0x11d/0x490 [mlx5_core]
mlx5e_change_nic_mtu+0x19/0x30 [mlx5_core]
netif_set_mtu_ext+0xfc/0x240
do_setlink.isra.0+0x226/0x1100
rtnl_newlink+0x7a9/0xba0
rtnetlink_rcv_msg+0x220/0x3c0
netlink_rcv_skb+0x4b/0xf0
netlink_unicast+0x255/0x380
netlink_sendmsg+0x1f3/0x420
__sock_sendmsg+0x38/0x60
____sys_sendmsg+0x1e8/0x240
___sys_sendmsg+0x7c/0xb0
[...]
__sys_sendmsg+0x5f/0xb0
do_syscall_64+0x55/0xc70
The problem applies for XDP_PASS as well which is handled in a different
code path in the driver.
This patch fixes the issue by doing page frag counting on all the
original XDP buffer fragments for all relevant XDP actions (XDP_TX ,
XDP_REDIRECT and XDP_PASS). This is basically reverting to the original
counting before the commit in the fixes tag.
As frag_page is still pointing to the original tail, the nr_frags
parameter to xdp_update_skb_frags_info() needs to be calculated
in a different way to reflect the new nr_frags.
Fixes: 87bcef158ac1 ("net/mlx5e: RX, Fix generating skb from non-linear xdp_buff for striding RQ")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Cc: Amery Hung <ameryhung@gmail.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of a TX error CQE, a recovery flow is triggered,
mlx5e_reset_txqsq_cc_pc() resets dma_fifo_cc to 0 but not dma_fifo_pc,
desyncing the DMA FIFO producer and consumer.
After recovery, the producer pushes new DMA entries at the old
dma_fifo_pc, while the consumer reads from position 0.
This causes us to unmap stale DMA addresses from before the recovery.
The DMA FIFO is a purely software construct with no HW counterpart.
At the point of reset, all WQEs have been flushed so dma_fifo_cc is
already equal to dma_fifo_pc. There is no need to reset either counter,
similar to how skb_fifo pc/cc are untouched.
Remove the 'dma_fifo_cc = 0' reset.
This fixes the following WARNING:
WARNING: CPU: 0 PID: 0 at drivers/iommu/dma-iommu.c:1240 iommu_dma_unmap_page+0x79/0x90
Modules linked in: mlx5_vdpa vringh vdpa bonding mlx5_ib mlx5_vfio_pci ipip mlx5_fwctl tunnel4 mlx5_core ib_ipoib geneve ip6_gre ip_gre gre nf_tables ip6_tunnel rdma_ucm ib_uverbs ib_umad vfio_pci vfio_pci_core act_mirred act_skbedit act_vlan vhost_net vhost tap ip6table_mangle ip6table_nat ip6table_filter ip6_tables iptable_mangle cls_matchall nfnetlink_cttimeout act_gact cls_flower sch_ingress vhost_iotlb iptable_raw tunnel6 vfio_iommu_type1 vfio openvswitch nsh rpcsec_gss_krb5 auth_rpcgss oid_registry xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat nf_nat xt_addrtype br_netfilter overlay zram zsmalloc rpcrdma ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_cm ib_core fuse [last unloaded: nf_tables]
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.13.0-rc5_for_upstream_min_debug_2024_12_30_21_33 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:iommu_dma_unmap_page+0x79/0x90
Code: 2b 4d 3b 21 72 26 4d 3b 61 08 73 20 49 89 d8 44 89 f9 5b 4c 89 f2 4c 89 e6 48 89 ef 5d 41 5c 41 5d 41 5e 41 5f e9 c7 ae 9e ff <0f> 0b 5b 5d 41 5c 41 5d 41 5e 41 5f c3 66 2e 0f 1f 84 00 00 00 00
Call Trace:
<IRQ>
? __warn+0x7d/0x110
? iommu_dma_unmap_page+0x79/0x90
? report_bug+0x16d/0x180
? handle_bug+0x4f/0x90
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? iommu_dma_unmap_page+0x79/0x90
? iommu_dma_unmap_page+0x2e/0x90
dma_unmap_page_attrs+0x10d/0x1b0
mlx5e_tx_wi_dma_unmap+0xbe/0x120 [mlx5_core]
mlx5e_poll_tx_cq+0x16d/0x690 [mlx5_core]
mlx5e_napi_poll+0x8b/0xac0 [mlx5_core]
__napi_poll+0x24/0x190
net_rx_action+0x32a/0x3b0
? mlx5_eq_comp_int+0x7e/0x270 [mlx5_core]
? notifier_call_chain+0x35/0xa0
handle_softirqs+0xc9/0x270
irq_exit_rcu+0x71/0xd0
common_interrupt+0x7f/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
Fixes: db75373c91b0 ("net/mlx5e: Recover Send Queue (SQ) from error state")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The check on mlx5_esw_host_functions_enabled(esw->dev) for adding VF
peer miss rules is incorrect. These rules match traffic from peer's VFs,
so the local device's host function status is irrelevant. Remove this
check to ensure peer VF traffic is properly handled regardless of local
host configuration.
Also fix the PF peer miss rule deletion to be symmetric with the add
path, so only attempt to delete the rule if it was actually created.
Fixes: 520369ef43a8 ("net/mlx5: Support disabling host PFs")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When moving to switchdev mode when the device doesn't support IPsec,
we try to clean up the IPsec resources anyway which causes the crash
below, fix that by correctly checking for IPsec support before trying
to clean up its resources.
[27642.515799] WARNING: arch/x86/mm/fault.c:1276 at
do_user_addr_fault+0x18a/0x680, CPU#4: devlink/6490
[27642.517159] Modules linked in: xt_conntrack xt_MASQUERADE
ip6table_nat ip6table_filter ip6_tables iptable_nat nf_nat xt_addrtype
rpcsec_gss_krb5 auth_rpcgss oid_registry overlay mlx5_fwctl nfnetlink
zram zsmalloc mlx5_ib fuse rpcrdma rdma_ucm ib_uverbs ib_iser libiscsi
scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_core
ib_core
[27642.521358] CPU: 4 UID: 0 PID: 6490 Comm: devlink Not tainted
6.19.0-rc5_for_upstream_min_debug_2026_01_14_16_47 #1 NONE
[27642.522923] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[27642.524528] RIP: 0010:do_user_addr_fault+0x18a/0x680
[27642.525362] Code: ff 0f 84 75 03 00 00 48 89 ee 4c 89 e7 e8 5e b9 22
00 49 89 c0 48 85 c0 0f 84 a8 02 00 00 f7 c3 60 80 00 00 74 22 31 c9 eb
ae <0f> 0b 48 83 c4 10 48 89 ea 48 89 de 4c 89 f7 5b 5d 41 5c 41 5d
41
[27642.528166] RSP: 0018:ffff88810770f6b8 EFLAGS: 00010046
[27642.529038] RAX: 0000000000000000 RBX: 0000000000000002 RCX:
ffff88810b980f00
[27642.530158] RDX: 00000000000000a0 RSI: 0000000000000002 RDI:
ffff88810770f728
[27642.531270] RBP: 00000000000000a0 R08: 0000000000000000 R09:
0000000000000000
[27642.532383] R10: 0000000000000000 R11: 0000000000000000 R12:
ffff888103f3c4c0
[27642.533499] R13: 0000000000000000 R14: ffff88810770f728 R15:
0000000000000000
[27642.534614] FS: 00007f197c741740(0000) GS:ffff88856a94c000(0000)
knlGS:0000000000000000
[27642.535915] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[27642.536858] CR2: 00000000000000a0 CR3: 000000011334c003 CR4:
0000000000172eb0
[27642.537982] Call Trace:
[27642.538466] <TASK>
[27642.538907] exc_page_fault+0x76/0x140
[27642.539583] asm_exc_page_fault+0x22/0x30
[27642.540282] RIP: 0010:_raw_spin_lock_irqsave+0x10/0x30
[27642.541134] Code: 07 85 c0 75 11 ba ff 00 00 00 f0 0f b1 17 75 06 b8
01 00 00 00 c3 31 c0 c3 90 0f 1f 44 00 00 53 9c 5b fa 31 c0 ba 01 00 00
00 <f0> 0f b1 17 75 05 48 89 d8 5b c3 89 c6 e8 7e 02 00 00 48 89 d8
5b
[27642.543936] RSP: 0018:ffff88810770f7d8 EFLAGS: 00010046
[27642.544803] RAX: 0000000000000000 RBX: 0000000000000202 RCX:
ffff888113ad96d8
[27642.545916] RDX: 0000000000000001 RSI: ffff88810770f818 RDI:
00000000000000a0
[27642.547027] RBP: 0000000000000098 R08: 0000000000000400 R09:
ffff88810b980f00
[27642.548140] R10: 0000000000000001 R11: ffff888101845a80 R12:
00000000000000a8
[27642.549263] R13: ffffffffa02a9060 R14: 00000000000000a0 R15:
ffff8881130d8a40
[27642.550379] complete_all+0x20/0x90
[27642.551010] mlx5e_ipsec_disable_events+0xb6/0xf0 [mlx5_core]
[27642.552022] mlx5e_nic_disable+0x12d/0x220 [mlx5_core]
[27642.552929] mlx5e_detach_netdev+0x66/0xf0 [mlx5_core]
[27642.553822] mlx5e_netdev_change_profile+0x5b/0x120 [mlx5_core]
[27642.554821] mlx5e_vport_rep_load+0x419/0x590 [mlx5_core]
[27642.555757] ? xa_load+0x53/0x90
[27642.556361] __esw_offloads_load_rep+0x54/0x70 [mlx5_core]
[27642.557328] mlx5_esw_offloads_rep_load+0x45/0xd0 [mlx5_core]
[27642.558320] esw_offloads_enable+0xb4b/0xc90 [mlx5_core]
[27642.559247] mlx5_eswitch_enable_locked+0x34e/0x4f0 [mlx5_core]
[27642.560257] ? mlx5_rescan_drivers_locked+0x222/0x2d0 [mlx5_core]
[27642.561284] mlx5_devlink_eswitch_mode_set+0x5ac/0x9c0 [mlx5_core]
[27642.562334] ? devlink_rate_set_ops_supported+0x21/0x3a0
[27642.563220] devlink_nl_eswitch_set_doit+0x67/0xe0
[27642.564026] genl_family_rcv_msg_doit+0xe0/0x130
[27642.564816] genl_rcv_msg+0x183/0x290
[27642.565466] ? __devlink_nl_pre_doit.isra.0+0x160/0x160
[27642.566329] ? devlink_nl_eswitch_get_doit+0x290/0x290
[27642.567181] ? devlink_nl_pre_doit_parent_dev_optional+0x20/0x20
[27642.568147] ? genl_family_rcv_msg_dumpit+0xf0/0xf0
[27642.568966] netlink_rcv_skb+0x4b/0xf0
[27642.569629] genl_rcv+0x24/0x40
[27642.570215] netlink_unicast+0x255/0x380
[27642.570901] ? __alloc_skb+0xfa/0x1e0
[27642.571560] netlink_sendmsg+0x1f3/0x420
[27642.572249] __sock_sendmsg+0x38/0x60
[27642.572911] __sys_sendto+0x119/0x180
[27642.573561] ? __sys_recvmsg+0x5c/0xb0
[27642.574227] __x64_sys_sendto+0x20/0x30
[27642.574904] do_syscall_64+0x55/0xc10
[27642.575554] entry_SYSCALL_64_after_hwframe+0x4b/0x53
[27642.576391] RIP: 0033:0x7f197c85e807
[27642.577050] Code: c7 c0 ff ff ff ff eb be 66 2e 0f 1f 84 00 00 00 00
00 90 f3 0f 1e fa 80 3d 45 08 0d 00 00 41 89 ca 74 10 b8 2c 00 00 00 0f
05 <48> 3d 00 f0 ff ff 77 69 c3 55 48 89 e5 53 48 83 ec 38 44 89 4d
d0
[27642.579846] RSP: 002b:00007ffebd4e2248 EFLAGS: 00000202 ORIG_RAX:
000000000000002c
[27642.581082] RAX: ffffffffffffffda RBX: 000055cfcd9cd2a0 RCX:
00007f197c85e807
[27642.582200] RDX: 0000000000000038 RSI: 000055cfcd9cd490 RDI:
0000000000000003
[27642.583320] RBP: 00007ffebd4e2290 R08: 00007f197c942200 R09:
000000000000000c
[27642.584437] R10: 0000000000000000 R11: 0000000000000202 R12:
0000000000000000
[27642.585555] R13: 000055cfcd9cd490 R14: 00007ffebd4e45d1 R15:
000055cfcd9cd2a0
[27642.586671] </TASK>
[27642.587121] ---[ end trace 0000000000000000 ]---
[27642.587910] BUG: kernel NULL pointer dereference, address:
00000000000000a0
Fixes: 664f76be38a1 ("net/mlx5: Fix IPsec cleanup over MPV device")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305142634.1813208-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
esw->work_queue executes esw_functions_changed_event_handler ->
esw_vfs_changed_event_handler and acquires the devlink lock.
.eswitch_mode_set (acquires devlink lock in devlink_nl_pre_doit) ->
mlx5_devlink_eswitch_mode_set -> mlx5_eswitch_disable_locked ->
mlx5_eswitch_event_handler_unregister -> flush_workqueue deadlocks
when esw_vfs_changed_event_handler executes.
Fix that by no longer flushing the work to avoid the deadlock, and using
a generation counter to keep track of work relevance. This avoids an old
handler manipulating an esw that has undergone one or more mode changes:
- the counter is incremented in mlx5_eswitch_event_handler_unregister.
- the counter is read and passed to the ephemeral mlx5_host_work struct.
- the work handler takes the devlink lock and bails out if the current
generation is different than the one it was scheduled to operate on.
- mlx5_eswitch_cleanup does the final draining before destroying the wq.
No longer flushing the workqueue has the side effect of maybe no longer
cancelling pending vport_change_handler work items, but that's ok since
those are disabled elsewhere:
- mlx5_eswitch_disable_locked disables the vport eq notifier.
- mlx5_esw_vport_disable disarms the HW EQ notification and marks
vport->enabled under state_lock to false to prevent pending vport
handler from doing anything.
- mlx5_eswitch_cleanup destroys the workqueue and makes sure all events
are disabled/finished.
Fixes: f1bc646c9a06 ("net/mlx5: Use devl_ API in mlx5_esw_offloads_devlink_port_register")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260305081019.1811100-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects truesize instead of DMA
write size. Different assumptions in enetc driver configuration lead to
negative tailroom.
Set frag_size to the same value as frame_sz.
Fixes: 2768b2e2f7d2 ("net: enetc: register XDP RX queues with frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-9-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buffer size instead
of DMA write size. Different assumptions in idpf driver configuration lead
to negative tailroom.
To make it worse, buffer sizes are not actually uniform in idpf when
splitq is enabled, as there are several buffer queues, so rxq->rx_buf_size
is meaningless in this case.
Use truesize of the first bufq in AF_XDP ZC, as there is only one. Disable
growing tail for regular splitq.
Fixes: ac8a861f632e ("idpf: prepare structures to support XDP")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-8-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buffer size instead
of DMA write size. Different assumptions in i40e driver configuration lead
to negative tailroom.
Set frag_size to the same value as frame_sz in shared pages mode, use new
helper to set frag_size when AF_XDP ZC is active.
Fixes: a045d2f2d03d ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-7-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current way of handling XDP RxQ info in i40e has a problem, where frag_size
is not updated when xsk_buff_pool is detached or when MTU is changed, this
leads to growing tail always failing for multi-buffer packets.
Couple XDP RxQ info registering with buffer allocations and unregistering
with cleaning the ring.
Fixes: a045d2f2d03d ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-6-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buff size instead
of DMA write size. Different assumptions in ice driver configuration lead
to negative tailroom.
This allows to trigger kernel panic, when using
XDP_ADJUST_TAIL_GROW_MULTI_BUFF xskxceiver test and changing packet size to
6912 and the requested offset to a huge value, e.g.
XSK_UMEM__MAX_FRAME_SIZE * 100.
Due to other quirks of the ZC configuration in ice, panic is not observed
in ZC mode, but tailroom growing still fails when it should not.
Use fill queue buffer truesize instead of DMA write size in XDP RxQ info.
Fix ZC mode too by using the new helper.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-5-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XDP RxQ info contains frag_size, which depends on the MTU. This makes the
old way of registering RxQ info before calculating new buffer sizes
invalid. Currently, it leads to frag_size being outdated, making it
sometimes impossible to grow tailroom in a mbuf packet. E.g. fragments are
actually 3K+, but frag size is still as if MTU was 1500.
Always register new XDP RxQ info after reconfiguring memory pools.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-4-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mtk_xdp_setup()
Reset eBPF program pointer to old_prog and do not decrease its ref-count
if mtk_open routine in mtk_xdp_setup() fails.
Fixes: 7c26c20da5d42 ("net: ethernet: mtk_eth_soc: add basic XDP support")
Suggested-by: Paolo Valerio <pvalerio@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260303-mtk-xdp-prog-ptr-fix-v2-1-97b6dbbe240f@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
VLAN register accesses on the MAC side require the PHY RX clock to be
active. When the network interface is down, the PHY is suspended and
the RX clock is unavailable, causing VLAN operations to fail with
timeouts.
The VLAN core automatically removes VID 0 after the interface goes down
and re-adds it when it comes back up, so these timeouts happen during
normal interface down/up:
# ip link set end1 down
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
renesas-gbeth 15c40000.ethernet end1: failed to kill vid 0081/0
Adding VLANs while the interface is down also fails:
# ip link add link end1 name end1.10 type vlan id 10
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
RTNETLINK answers: Device or resource busy
To fix this, check if the interface is up before accessing VLAN registers.
The software state is always kept up to date regardless of interface state.
When the interface is brought up, stmmac_vlan_restore() is called
to write the VLAN state to hardware.
Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-5-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the network interface is opened or resumed, a DMA reset is performed,
which resets all hardware state, including VLAN state. Currently, only
the resume path is restoring the VLAN state via
stmmac_restore_hw_vlan_rx_fltr(), but that is incomplete: the VLAN hash
table and the VLAN_TAG control bits are not restored.
Therefore, add stmmac_vlan_restore(), which restores the full VLAN
state by updating both the HW filter entries and the hash table, and
call it from both the open and resume paths.
The VLAN restore is moved outside of phylink_rx_clk_stop_block/unblock
in the resume path because receive clock stop is already disabled when
stmmac supports VLAN.
Also, remove the hash readback code in vlan_restore_hw_rx_fltr() that
attempts to restore VTHM by reading VLAN_HASH_TABLE, as it always reads
zero after DMA reset, making it dead code.
Fixes: 3cd1cfcba26e ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-4-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The double VLAN bits (EDVLP, ESVL, DOVLTC) are handled inconsistently
between the two vlan_update_hash() implementations:
- dwxgmac2_update_vlan_hash() explicitly clears the double VLAN bits when
is_double is false, meaning that adding a 802.1Q VLAN will disable
double VLAN mode:
$ ip link add link eth0 name eth0.200 type vlan id 200 protocol 802.1ad
$ ip link add link eth0 name eth0.100 type vlan id 100
# Double VLAN bits no longer set
- vlan_update_hash() sets these bits and only clears them when the last
VLAN has been removed, so double VLAN mode remains enabled even after all
802.1AD VLANs are removed.
Address both issues by tracking the number of active 802.1AD VLANs in
priv->num_double_vlans. Pass this count to stmmac_vlan_update() so both
implementations correctly set the double VLAN bits when any 802.1AD
VLAN is active, and clear them only when none remain.
Also update vlan_update_hash() to explicitly clear the double VLAN bits
when is_double is false, matching the dwxgmac2 behavior.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-3-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
stmmac_vlan_rx_add_vid() updates active_vlans and the VLAN hash
register before writing the HW filter entry. If the filter write
fails, it leaves a stale VID in active_vlans and the hash register.
stmmac_vlan_rx_kill_vid() has the reverse problem: it clears
active_vlans before removing the HW filter. On failure, the VID is
gone from active_vlans but still present in the HW filter table.
To fix this, reorder the operations to update the hash table first,
then attempt the HW filter operation. If the HW filter fails, roll
back both the active_vlans bitmap and the hash table by calling
stmmac_vlan_update() again.
Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-2-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-03-03 (ice, libie, iavf, igb, igc)
Larysa removes VF restriction for LLDP filters on ice to allow for LLDP
traffic to reach the correct destination.
Jakub adds retry mechanism for AdminQ Read/Write SFF EEPROM call to
follow hardware specification on ice.
Zilin Guan adds cleanup path to free XDP rings on failure in
ice_set_ringparam().
Michal bypasses firmware logging unroll in libie when it isn't supported.
Kohei Enju fixes iavf to take into account hardware MTU support when
setting max MTU values.
Vivek Behera fixes issues on igb and igc using incorrect IRQs when Tx/Rx
queues do not share the same IRQ.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Fix trigger of incorrect irq in igc_xsk_wakeup function
igb: Fix trigger of incorrect irq in igb_xsk_wakeup
iavf: fix netdev->max_mtu to respect actual hardware limit
libie: don't unroll if fwlog isn't supported
ice: Fix memory leak in ice_set_ringparam()
ice: fix retry for AQ command 0x06EE
ice: reintroduce retry mechanism for indirect AQ
ice: fix adding AQ LLDP filter for VF
====================
Link: https://patch.msgid.link/20260303231155.2895065-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The xgbe_powerdown() and xgbe_powerup() functions use spinlocks
(spin_lock_irqsave) while calling functions that may sleep:
- napi_disable() can sleep waiting for NAPI polling to complete
- flush_workqueue() can sleep waiting for pending work items
This causes a "BUG: scheduling while atomic" error during suspend/resume
cycles on systems using the AMD XGBE Ethernet controller.
The spinlock protection in these functions is unnecessary as these
functions are called from suspend/resume paths which are already serialized
by the PM core
Fix this by removing the spinlock. Since only code that takes this lock
is xgbe_powerdown() and xgbe_powerup(), remove it completely.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260302042124.1386445-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch addresses the issue where the igc_xsk_wakeup function
was triggering an incorrect IRQ for tx-0 when the i226 is configured
with only 2 combined queues or in an environment with 2 active CPU cores.
This prevented XDP Zero-copy send functionality in such split IRQ
configurations.
The fix implements the correct logic for extracting q_vectors saved
during rx and tx ring allocation and utilizes flags provided by the
ndo_xsk_wakeup API to trigger the appropriate IRQ.
Fixes: fc9df2a0b520 ("igc: Enable RX via AF_XDP zero-copy")
Fixes: 15fd021bc427 ("igc: Add Tx hardware timestamp request for AF_XDP zero-copy packet")
Signed-off-by: Vivek Behera <vivek.behera@siemens.com>
Reviewed-by: Jacob Keller <jacob.keller@intel.com>
Reviewed-by: Aleksandr loktinov <aleksandr.loktionov@intel.com>
Reviewed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Song Yoong Siang <yoong.siang.song@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current implementation in the igb_xsk_wakeup expects
the Rx and Tx queues to share the same irq. This would lead
to triggering of incorrect irq in split irq configuration.
This patch addresses this issue which could impact environments
with 2 active cpu cores
or when the number of queues is reduced to 2 or less
cat /proc/interrupts | grep eno2
167: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
0-edge eno2
168: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
1-edge eno2-rx-0
169: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
2-edge eno2-rx-1
170: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
3-edge eno2-tx-0
171: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
4-edge eno2-tx-1
Furthermore it uses the flags input argument to trigger either rx, tx or
both rx and tx irqs as specified in the ndo_xsk_wakeup api documentation
Fixes: 80f6ccf9f116 ("igb: Introduce XSK data structures and helpers")
Signed-off-by: Vivek Behera <vivek.behera@siemens.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
iavf sets LIBIE_MAX_MTU as netdev->max_mtu, ignoring vf_res->max_mtu
from PF [1]. This allows setting an MTU beyond the actual hardware
limit, causing TX queue timeouts [2].
Set correct netdev->max_mtu using vf_res->max_mtu from the PF.
Note that currently PF drivers such as ice/i40e set the frame size in
vf_res->max_mtu, not MTU. Convert vf_res->max_mtu to MTU before setting
netdev->max_mtu.
[1]
# ip -j -d link show $DEV | jq '.[0].max_mtu'
16356
[2]
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 1: transmit queue 0 timed out 5692 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 6: transmit queue 3 timed out 5312 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
...
Fixes: 5fa4caff59f2 ("iavf: switch to Page Pool")
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The libie_fwlog_deinit() function can be called during driver unload
even when firmware logging was never properly initialized. This led to call
trace:
[ 148.576156] Oops: Oops: 0000 [#1] SMP NOPTI
[ 148.576167] CPU: 80 UID: 0 PID: 12843 Comm: rmmod Kdump: loaded Not tainted 6.17.0-rc7next-queue-3oct-01915-g06d79d51cf51 #1 PREEMPT(full)
[ 148.576177] Hardware name: HPE ProLiant DL385 Gen10 Plus/ProLiant DL385 Gen10 Plus, BIOS A42 07/18/2020
[ 148.576182] RIP: 0010:__dev_printk+0x16/0x70
[ 148.576196] Code: 1f 44 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 41 55 41 54 49 89 d4 55 48 89 fd 53 48 85 f6 74 3c <4c> 8b 6e 50 48 89 f3 4d 85 ed 75 03 4c 8b 2e 48 89 df e8 f3 27 98
[ 148.576204] RSP: 0018:ffffd2fd7ea17a48 EFLAGS: 00010202
[ 148.576211] RAX: ffffd2fd7ea17aa0 RBX: ffff8eb288ae2000 RCX: 0000000000000000
[ 148.576217] RDX: ffffd2fd7ea17a70 RSI: 00000000000000c8 RDI: ffffffffb68d3d88
[ 148.576222] RBP: ffffffffb68d3d88 R08: 0000000000000000 R09: 0000000000000000
[ 148.576227] R10: 00000000000000c8 R11: ffff8eb2b1a49400 R12: ffffd2fd7ea17a70
[ 148.576231] R13: ffff8eb3141fb000 R14: ffffffffc1215b48 R15: ffffffffc1215bd8
[ 148.576236] FS: 00007f5666ba6740(0000) GS:ffff8eb2472b9000(0000) knlGS:0000000000000000
[ 148.576242] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 148.576247] CR2: 0000000000000118 CR3: 000000011ad17000 CR4: 0000000000350ef0
[ 148.576252] Call Trace:
[ 148.576258] <TASK>
[ 148.576269] _dev_warn+0x7c/0x96
[ 148.576290] libie_fwlog_deinit+0x112/0x117 [libie_fwlog]
[ 148.576303] ixgbe_remove+0x63/0x290 [ixgbe]
[ 148.576342] pci_device_remove+0x42/0xb0
[ 148.576354] device_release_driver_internal+0x19c/0x200
[ 148.576365] driver_detach+0x48/0x90
[ 148.576372] bus_remove_driver+0x6d/0xf0
[ 148.576383] pci_unregister_driver+0x2e/0xb0
[ 148.576393] ixgbe_exit_module+0x1c/0xd50 [ixgbe]
[ 148.576430] __do_sys_delete_module.isra.0+0x1bc/0x2e0
[ 148.576446] do_syscall_64+0x7f/0x980
It can be reproduced by trying to unload ixgbe driver in recovery mode.
Fix that by checking if fwlog is supported before doing unroll.
Fixes: 641585bc978e ("ixgbe: fwlog support for e610")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In ice_set_ringparam, tx_rings and xdp_rings are allocated before
rx_rings. If the allocation of rx_rings fails, the code jumps to
the done label leaking both tx_rings and xdp_rings. Furthermore, if
the setup of an individual Rx ring fails during the loop, the code jumps
to the free_tx label which releases tx_rings but leaks xdp_rings.
Fix this by introducing a free_xdp label and updating the error paths to
ensure both xdp_rings and tx_rings are properly freed if rx_rings
allocation or setup fails.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
Fixes: fcea6f3da546 ("ice: Add stats and ethtool support")
Fixes: efc2214b6047 ("ice: Add support for XDP")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Executing ethtool -m can fail reporting a netlink I/O error while firmware
link management holds the i2c bus used to communicate with the module.
According to Intel(R) Ethernet Controller E810 Datasheet Rev 2.8 [1]
Section 3.3.10.4 Read/Write SFF EEPROM (0x06EE)
request should to be retried upon receiving EBUSY from firmware.
Commit e9c9692c8a81 ("ice: Reimplement module reads used by ethtool")
implemented it only for part of ice_get_module_eeprom(), leaving all other
calls to ice_aq_sff_eeprom() vulnerable to returning early on getting
EBUSY without retrying.
Remove the retry loop from ice_get_module_eeprom() and add Admin Queue
(AQ) command with opcode 0x06EE to the list of commands that should be
retried on receiving EBUSY from firmware.
Cc: stable@vger.kernel.org
Fixes: e9c9692c8a81 ("ice: Reimplement module reads used by ethtool")
Signed-off-by: Jakub Staniszewski <jakub.staniszewski@linux.intel.com>
Co-developed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://www.intel.com/content/www/us/en/content-details/613875/intel-ethernet-controller-e810-datasheet.html [1]
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add retry mechanism for indirect Admin Queue (AQ) commands. To do so we
need to keep the command buffer.
This technically reverts commit 43a630e37e25
("ice: remove unused buffer copy code in ice_sq_send_cmd_retry()"),
but combines it with a fix in the logic by using a kmemdup() call,
making it more robust and less likely to break in the future due to
programmer error.
Cc: Michal Schmidt <mschmidt@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 3056df93f7a8 ("ice: Re-send some AQ commands, as result of EBUSY AQ error")
Signed-off-by: Jakub Staniszewski <jakub.staniszewski@linux.intel.com>
Co-developed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The referenced commit came from a misunderstanding of the FW LLDP filter
AQ (Admin Queue) command due to the error in the internal documentation.
Contrary to the assumptions in the original commit, VFs can be added and
deleted from this filter without any problems. Introduced dev_info message
proved to be useful, so reverting the whole commit does not make sense.
Without this fix, trusted VFs do not receive LLDP traffic, if there is an
AQ LLDP filter on PF. When trusted VF attempts to add an LLDP multicast
MAC address, the following message can be seen in dmesg on host:
ice 0000:33:00.0: Failed to add Rx LLDP rule on VSI 20 error: -95
Revert checking VSI type when adding LLDP filter through AQ.
Fixes: 4d5a1c4e6d49 ("ice: do not add LLDP-specific filter if not necessary")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Utilize READ_ONCE and WRITE_ONCE APIs for IO queue Tx/Rx
variable access to prevent compiler optimization and reordering.
Additionally, ensure IO queue OUT/IN_CNT registers are flushed
by performing a read-back after writing.
The compiler could reorder reads/writes to pkts_pending, last_pkt_count,
etc., causing stale values to be used when calculating packets to process
or register updates to send to hardware. The Octeon hardware requires a
read-back after writing to OUT_CNT/IN_CNT registers to ensure the write
has been flushed through any posted write buffers before the interrupt
resend bit is set. Without this, we have observed cases where the hardware
didn't properly update its internal state.
wmb/rmb only provides ordering guarantees but doesn't prevent the compiler
from performing optimizations like caching in registers, load tearing etc.
Fixes: 1cd3b407977c3 ("octeon_ep_vf: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-5-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Relocate IQ/OQ IN/OUT_CNTS updates to occur before NAPI completion.
Moving the IQ/OQ counter updates before napi_complete_done ensures
1. Counter registers are updated before re-enabling interrupts.
2. Prevents a race where new packets arrive but counters aren't properly
synchronized.
Fixes: 1cd3b407977c3 ("octeon_ep_vf: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-4-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Utilize READ_ONCE and WRITE_ONCE APIs for IO queue Tx/Rx
variable access to prevent compiler optimization and reordering.
Additionally, ensure IO queue OUT/IN_CNT registers are flushed
by performing a read-back after writing.
The compiler could reorder reads/writes to pkts_pending, last_pkt_count,
etc., causing stale values to be used when calculating packets to process
or register updates to send to hardware. The Octeon hardware requires a
read-back after writing to OUT_CNT/IN_CNT registers to ensure the write
has been flushed through any posted write buffers before the interrupt
resend bit is set. Without this, we have observed cases where the hardware
didn't properly update its internal state.
wmb/rmb only provides ordering guarantees but doesn't prevent the compiler
from performing optimizations like caching in registers, load tearing etc.
Fixes: 37d79d0596062 ("octeon_ep: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-3-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Relocate IQ/OQ IN/OUT_CNTS updates to occur before NAPI completion,
and replace napi_complete with napi_complete_done.
Moving the IQ/OQ counter updates before napi_complete_done ensures
1. Counter registers are updated before re-enabling interrupts.
2. Prevents a race where new packets arrive but counters aren't properly
synchronized.
napi_complete_done (vs napi_complete) allows for better
interrupt coalescing.
Fixes: 37d79d0596062 ("octeon_ep: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-2-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Extend the MAC_TCR_SS (Speed Select) register field width from 2 bits
to 3 bits to properly support all speed settings.
The MAC_TCR register's SS field encoding requires 3 bits to represent
all supported speeds:
- 0x00: 10Gbps (XGMII)
- 0x02: 2.5Gbps (GMII) / 100Mbps
- 0x03: 1Gbps / 10Mbps
- 0x06: 2.5Gbps (XGMII) - P100a only
With only 2 bits, values 0x04-0x07 cannot be represented, which breaks
2.5G XGMII mode on newer platforms and causes incorrect speed select
values to be programmed.
Fixes: 07445f3c7ca1 ("amd-xgbe: Add support for 10 Mbps speed")
Co-developed-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260226170753.250312-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
speed is not 1G
When both eth interfaces with links up are added to a bridge or hsr
interface, ping fails if the link speed is not 1Gbps (e.g., 100Mbps).
The issue is seen because when switching to offload (bridge/hsr) mode,
prueth_emac_restart() restarts the firmware and clears DRAM with
memset_io(), setting all memory to 0. This includes PORT_LINK_SPEED_OFFSET
which firmware reads for link speed. The value 0 corresponds to
FW_LINK_SPEED_1G (0x00), so for 1Gbps links the default value is correct
and ping works. For 100Mbps links, the firmware needs FW_LINK_SPEED_100M
(0x01) but gets 0 instead, causing ping to fail. The function
emac_adjust_link() is called to reconfigure, but it detects no state change
(emac->link is still 1, speed/duplex match PHY) so new_state remains false
and icssg_config_set_speed() is never called to correct the firmware speed
value.
The fix resets emac->link to 0 before calling emac_adjust_link() in
prueth_emac_common_start(). This forces new_state=true, ensuring
icssg_config_set_speed() is called to write the correct speed value to
firmware memory.
Fixes: 06feac15406f ("net: ti: icssg-prueth: Fix emac link speed handling")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20260226102356.2141871-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 31a7a0bbeb00 ("dpaa2-switch: add bounds check for if_id in IRQ
handler") introduces a range check for if_id to avoid an out-of-bounds
access. If an out-of-bounds if_id is detected, the interrupt status is
not cleared. This may result in an interrupt storm.
Clear the interrupt status after detecting an out-of-bounds if_id to avoid
the problem.
Found by an experimental AI code review agent at Google.
Fixes: 31a7a0bbeb00 ("dpaa2-switch: add bounds check for if_id in IRQ handler")
Cc: Junrui Luo <moonafterrain@outlook.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260227055812.1777915-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-02-19 (idpf, ice, i40e, ixgbevf, e1000e)
For idpf:
Li Li moves the check for software marker to occur after incrementing
next to clean to avoid re-encountering the same packet. He also adds a
couple of checks to prevent NULL pointer dereferences and NULLs rss_key,
after free, in error path so that later checks are properly evaluated.
Brian Vazquez adjusts IRQ naming to have correlation with netdev naming.
Sreedevi removes validation of action type as part of ntuple rule
deletion.
For ice:
Aaron Ma breaks RDMA initialization into two steps and adjusts calls so
that VSIs are entirely configured before plugging.
Michal Schmidt fixes initialization of loopback VSI to have proper
resources allocated to allow for loopback testing to occur.
For i40e:
Thomas Gleixner fixes a leak of preempt count by replacing get_cpu()
with smp_processor_id().
For ixgbevf:
Jedrzej adds a check for mailbox version before attempting to call an
associated link state call that is supported in that mailbox version.
For e1000e:
Vitaly clears power gating feature for Panther Lake systems to avoid
packet issues.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: clear DPG_EN after reset to avoid autonomous power-gating
e1000e: introduce new board type for Panther Lake PCH
ixgbevf: fix link setup issue
i40e: Fix preempt count leak in napi poll tracepoint
ice: fix crash in ethtool offline loopback test
ice: recap the VSI and QoS info after rebuild
idpf: Fix flow rule delete failure due to invalid validation
idpf: change IRQ naming to match netdev and ethtool queue numbering
idpf: nullify pointers after they are freed
idpf: skip deallocating txq group's txqs if it is NULL
idpf: skip deallocating bufq_sets from rx_qgrp if it is NULL
idpf: increment completion queue next_to_clean in sw marker wait routine
====================
Link: https://patch.msgid.link/20260225211546.1949260-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MANA hardware requires at least one doorbell ring every 8 wraparounds
of the CQ. The driver rings the doorbell as a form of flow control to
inform hardware that CQEs have been consumed.
The NAPI poll functions mana_poll_tx_cq() and mana_poll_rx_cq() can
poll up to CQE_POLLING_BUFFER (512) completions per call. If the CQ
has fewer than 512 entries, a single poll call can process more than
4 wraparounds without ringing the doorbell. The doorbell threshold
check also uses ">" instead of ">=", delaying the ring by one extra
CQE beyond 4 wraparounds. Combined, these issues can cause the driver
to exceed the 8-wraparound hardware limit, leading to missed
completions and stalled queues.
Fix this by capping the number of CQEs polled per call to 4 wraparounds
of the CQ in both TX and RX paths. Also change the doorbell threshold
from ">" to ">=" so the doorbell is rung as soon as 4 wraparounds are
reached.
Cc: stable@vger.kernel.org
Fixes: 58a63729c957 ("net: mana: Fix doorbell out of order violation and avoid unnecessary doorbell rings")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260226192833.1050807-1-longli@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ALE table
In the current implementation, flushing multicast entries in MAC mode
incorrectly deletes entries for all ports instead of only the target port,
disrupting multicast traffic on other ports. The cause is adding multicast
entries by setting only host port bit, and not setting the MAC port bits.
Fix this by setting the MAC port's bit in the port mask while adding the
multicast entry. Also fix the flush logic to preserve the host port bit
during removal of MAC port and free ALE entries when mask contains only
host port.
Fixes: 5c50a856d550 ("drivers: net: ethernet: cpsw: add multicast address to ALE table")
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224181359.2055322-1-c-vankar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from IPsec, Bluetooth and netfilter
Current release - regressions:
- wifi: fix dev_alloc_name() return value check
- rds: fix recursive lock in rds_tcp_conn_slots_available
Current release - new code bugs:
- vsock: lock down child_ns_mode as write-once
Previous releases - regressions:
- core:
- do not pass flow_id to set_rps_cpu()
- consume xmit errors of GSO frames
- netconsole: avoid OOB reads, msg is not nul-terminated
- netfilter: h323: fix OOB read in decode_choice()
- tcp: re-enable acceptance of FIN packets when RWIN is 0
- udplite: fix null-ptr-deref in __udp_enqueue_schedule_skb().
- wifi: brcmfmac: fix potential kernel oops when probe fails
- phy: register phy led_triggers during probe to avoid AB-BA deadlock
- eth:
- bnxt_en: fix deleting of Ntuple filters
- wan: farsync: fix use-after-free bugs caused by unfinished tasklets
- xscale: check for PTP support properly
Previous releases - always broken:
- tcp: fix potential race in tcp_v6_syn_recv_sock()
- kcm: fix zero-frag skb in frag_list on partial sendmsg error
- xfrm:
- fix race condition in espintcp_close()
- always flush state and policy upon NETDEV_UNREGISTER event
- bluetooth:
- purge error queues in socket destructors
- fix response to L2CAP_ECRED_CONN_REQ
- eth:
- mlx5:
- fix circular locking dependency in dump
- fix "scheduling while atomic" in IPsec MAC address query
- gve: fix incorrect buffer cleanup for QPL
- team: avoid NETDEV_CHANGEMTU event when unregistering slave
- usb: validate USB endpoints"
* tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
netfilter: nf_conntrack_h323: fix OOB read in decode_choice()
dpaa2-switch: validate num_ifs to prevent out-of-bounds write
net: consume xmit errors of GSO frames
vsock: document write-once behavior of the child_ns_mode sysctl
vsock: lock down child_ns_mode as write-once
selftests/vsock: change tests to respect write-once child ns mode
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
net/mlx5: Fix missing devlink lock in SRIOV enable error path
net/mlx5: E-switch, Clear legacy flag when moving to switchdev
net/mlx5: LAG, disable MPESW in lag_disable_change()
net/mlx5: DR, Fix circular locking dependency in dump
selftests: team: Add a reference count leak test
team: avoid NETDEV_CHANGEMTU event when unregistering slave
net: mana: Fix double destroy_workqueue on service rescan PCI path
MAINTAINERS: Update maintainer entry for QUALCOMM ETHQOS ETHERNET DRIVER
dpll: zl3073x: Remove redundant cleanup in devm_dpll_init()
selftests/net: packetdrill: Verify acceptance of FIN packets when RWIN is 0
tcp: re-enable acceptance of FIN packets when RWIN is 0
vsock: Use container_of() to get net namespace in sysctl handlers
net: usb: kaweth: validate USB endpoints
...
|
|
The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes()
but never validates it against DPSW_MAX_IF (64). This value controls
iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices
into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports
num_ifs >= 64, the loop can write past the array bounds.
Add a bound check for num_ifs in dpaa2_switch_init().
dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port
num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all
ports match the flood filter, the loop fills all 64 slots and the control
interface write overflows by one entry.
The check uses >= because num_ifs == DPSW_MAX_IF is also functionally
broken.
build_if_id_bitmap() silently drops any ID >= 64:
if (id[i] < DPSW_MAX_IF)
bmap[id[i] / 64] |= ...
Fixes: 539dda3c5d19 ("staging: dpaa2-switch: properly setup switching domains")
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/SYBPR01MB78812B47B7F0470B617C408AAF74A@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
