| Age | Commit message (Collapse) | Author |
|---|
|
spi_nor_erase_{sector,chip}()
[ Upstream commit f8cd9f632f4415b1e8838bdca8ab42cfb37a6584 ]
For erase operations, reg_proto must be used as indicated in
struct spi_nor description in spi-nor.h.
This issue was found when DT property spi-tx-bus-width is set to 4.
In this case the spi_mem_op->addr.buswidth is set to 4 for erase command
which is not correct.
Tested on stm32mp157c-ev1 board with mx66l51235f spi-nor.
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
[ta: use nor->reg_proto in spi_nor_controller_ops_erase()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220629133013.3382393-1-patrice.chotard@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ac4f83482afbfd927d0fe118151b747cf175e724 ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220620152313.708768-1-broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c223a38d62e57aa60a890ea7247e3c58a54478e6 ]
If rpcif_hw_init() fails, Runtime PM is left enabled.
Fixes: b04cc0d912eb80d3 ("memory: renesas-rpc-if: Add support for RZ/G2L")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/f3070e1af480cb252ae183d479a593dbbf947685.1655457790.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28607b426c3d050714f250d0faeb99d2e9106e90 ]
For all but one error path clk_disable_unprepare() is already there. Add
it to the one location where it's missing.
Fixes: 481815a6193b ("mtd: st_spi_fsm: Handle clk_prepare_enable/clk_disable_unprepare.")
Fixes: 69d5af8d016c ("mtd: st_spi_fsm: Obtain and use EMI clock")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e607879b0da18c451de5e91daf239cc2f2f8ff2d ]
of_find_node_by_path() returns a node pointer with refcount incremented,
we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bb17230c61a6 ("mtd: parsers: ofpart: support BCM4908 fixed partitions")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220605070726.5979-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f7e62815cf3cbbcb1b8cb21649fb4dfdb3aa016 ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 237960880960 ("mtd: partitions: redboot: seek fis-index-block in the right node")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220526110652.64849-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a61528d997619a518ee8c51cf0ef0513021afaff ]
There is a deadlock between sm_release and sm_cache_flush_work
which is a work item. The cancel_work_sync in sm_release will
not return until sm_cache_flush_work is finished. If we hold
mutex_lock and use cancel_work_sync to wait the work item to
finish, the work item also requires mutex_lock. As a result,
the sm_release will be blocked forever. The race condition is
shown below:
(Thread 1) | (Thread 2)
sm_release |
mutex_lock(&ftl->mutex) | sm_cache_flush_work
| mutex_lock(&ftl->mutex)
cancel_work_sync | ...
This patch moves del_timer_sync and cancel_work_sync out of
mutex_lock in order to mitigate deadlock.
Fixes: 7d17c02a01a1 ("mtd: Add new SmartMedia/xD FTL")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220524044841.10517-1-duoming@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ec0da06337751b18f6dee06b6526e0f0d6e80369 ]
When meson_nfc_nand_chip_cleanup() is called, it will call:
meson_nfc_free_buffer(&meson_chip->nand);
nand_cleanup(&meson_chip->nand);
nand_cleanup() in turn will call nand_detach() which calls the
.detach_chip() which is here meson_nand_detach_chip().
meson_nand_detach_chip() already calls meson_nfc_free_buffer(), so we
could double free some memory.
Fix it by removing the unneeded explicit call to meson_nfc_free_buffer().
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/ec15c358b8063f7c50ff4cd628cf0d2e14e43f49.1653064877.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77087a04c8fd554134bddcb8a9ff87b21f357926 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc192 ("mtd: physmap_of: add a hook for Versatile write protection")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220523143255.4376-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33ec82a6d2b119938f26e5c8040ed5d92378eb54 ]
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc192 ("mtd: physmap_of: add a hook for Versatile write protection")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220523140205.48625-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7499bfeedb47efc1ee4dc793b92c610d46e6d6a6 upstream.
In current implementation the Arasan NAND driver is updating the
system clock(i.e., anand->clk) in accordance to the timing modes
(i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
updated instead. This patch keeps the system clock unchanged and updates
the NAND bus clock as per the timing modes.
Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-2-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e16eceea863b417fd328588b1be1a79de0bc937f upstream.
According to the Arasan NAND controller spec, the flash clock rate for SDR
must be <= 100 MHz, while for NV-DDR it must be the same as the rate of the
CLK line for the mode. The driver previously always set 100 MHz for NV-DDR,
which would result in incorrect behavior for NV-DDR modes 0-4.
The appropriate clock rate can be calculated from the NV-DDR timing
parameters as 1/tCK, or for rates measured in picoseconds,
10^12 / nand_nvddr_timings->tCK_min.
Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Olga Kitaina <okitain@gmail.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-3-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0fddf9ad06fd9f439f137139861556671673e31c upstream.
06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026350 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b1206122069aa ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 8d45b05f7eafc92dd69c006c5c31e0b4933a1a07 which is
commit 06781a5026350cde699d2d10c9914a25c1524f45 upstream.
It is reported to cause data loss, so revert it to prevent that from
happening for users of this driver.
Reported-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20220701110341.3094023-1-s.hauer@pengutronix.de/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06781a5026350cde699d2d10c9914a25c1524f45 upstream.
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b1206122069aa ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c03a1c21d72210f81cb369cc528e3fde4b45411 ]
There is an use-after-free problem for 'eba_tbl' in ubi_create_volume()'s
error handling path:
ubi_eba_replace_table(vol, eba_tbl)
vol->eba_tbl = tbl
out_mapping:
ubi_eba_destroy_table(eba_tbl) // Free 'eba_tbl'
out_unlock:
put_device(&vol->dev)
vol_release
kfree(tbl->entries) // UAF
Fix it by removing redundant 'eba_tbl' releasing.
Fetch a reproducer in [Link].
Fixes: 493cfaeaa0c9b ("mtd: utilize new cdev_device_add helper function")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215965
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d09e9a2bddba6c48e0fddb16c4383172ac593251 ]
There at least 6 PEBs reserved on UBI device:
1. EBA_RESERVED_PEBS[1]
2. WL_RESERVED_PEBS[1]
3. UBI_LAYOUT_VOLUME_EBS[2]
4. MIN_FASTMAP_RESERVED_PEBS[2]
When all ubi volumes take all their PEBs, there are 3 (EBA_RESERVED_PEBS +
WL_RESERVED_PEBS + MIN_FASTMAP_RESERVED_PEBS - MIN_FASTMAP_TAKEN_PEBS[1])
free PEBs. Since commit f9c34bb529975fe ("ubi: Fix producing anchor PEBs")
and commit 4b68bf9a69d22dd ("ubi: Select fastmap anchor PEBs considering
wear level rules") applied, there is only 1 (3 - FASTMAP_ANCHOR_PEBS[1] -
FASTMAP_NEXT_ANCHOR_PEBS[1]) free PEB to fill pool and wl_pool, after
filling pool, wl_pool is always empty. So, UBI could be stuck in an
infinite loop:
ubi_thread system_wq
wear_leveling_worker <--------------------------------------------------
get_peb_for_wl |
// fm_wl_pool, used = size = 0 |
schedule_work(&ubi->fm_work) |
|
update_fastmap_work_fn |
ubi_update_fastmap |
ubi_refill_pools |
// ubi->free_count - ubi->beb_rsvd_pebs < 5 |
// wl_pool is not filled with any PEBs |
schedule_erase(old_fm_anchor) |
ubi_ensure_anchor_pebs |
__schedule_ubi_work(wear_leveling_worker) |
|
__erase_worker |
ensure_wear_leveling |
__schedule_ubi_work(wear_leveling_worker) --------------------------
, which cause high cpu usage of ubi_bgt:
top - 12:10:42 up 5 min, 2 users, load average: 1.76, 0.68, 0.27
Tasks: 123 total, 3 running, 54 sleeping, 0 stopped, 0 zombie
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
1589 root 20 0 0 0 0 R 45.0 0.0 0:38.86 ubi_bgt0d
319 root 20 0 0 0 0 I 15.2 0.0 0:15.29 kworker/0:3-eve
371 root 20 0 0 0 0 I 14.9 0.0 0:12.85 kworker/3:3-eve
20 root 20 0 0 0 0 I 11.3 0.0 0:05.33 kworker/1:0-eve
202 root 20 0 0 0 0 I 11.3 0.0 0:04.93 kworker/2:3-eve
In commit 4b68bf9a69d22dd ("ubi: Select fastmap anchor PEBs considering
wear level rules"), there are three key changes:
1) Choose the fastmap anchor when the most free PEBs are available.
2) Enable anchor move within the anchor area again as it is useful
for distributing wear.
3) Import a candidate fm anchor and check this PEB's erase count during
wear leveling. If the wear leveling limit is exceeded, use the used
anchor area PEB with the lowest erase count to replace it.
The anchor candidate can be removed, we can check fm_anchor PEB's erase
count during wear leveling. Fix it by:
1) Removing 'fm_next_anchor' and check 'fm_anchor' during wear leveling.
2) Preferentially filling one free peb into fm_wl_pool in condition of
ubi->free_count > ubi->beb_rsvd_pebs, then try to reserve enough
free count for fastmap non anchor pebs after the above prerequisites
are met.
Then, there are at least 1 PEB in pool and 1 PEB in wl_pool after calling
ubi_refill_pools() with all erase works done.
Fetch a reproducer in [Link].
Fixes: 4b68bf9a69d22dd ("ubi: Select fastmap anchor PEBs ... rules")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215407
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0a8e98305f63deaf0a799d5cf5532cc83af035d1 upstream.
Since commit dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to
check correct value") buffered writes fail on S29GL064N. This is
because, on S29GL064N, reads return 0xFF at the end of DQ polling for
write completion, where as, chip_good() check expects actual data
written to the last location to be returned post DQ polling completion.
Fix is to revert to using chip_good() for S29GL064N which only checks
for DQ lines to settle down to determine write completion.
Link: https://lore.kernel.org/r/b687c259-6413-26c9-d4c9-b3afa69ea124@pengutronix.de/
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Cc: stable@vger.kernel.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-3-ikegami.t@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 083084df578a8bdb18334f69e7b32d690aaa3247 upstream.
This is a preparation patch for the S29GL064N buffer writes fix. There
is no functional change.
Link: https://lore.kernel.org/r/b687c259-6413-26c9-d4c9-b3afa69ea124@pengutronix.de/
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-2-ikegami.t@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ddf66aefd685fd46500b9917333e1b1e118276dc ]
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
Fixes: 0b1039f016e8 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-2-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a28ed09dafee20da51eb26452950839633afd824 ]
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70dd83d737d8900b2d98db6dc6b928c596334d37 ]
Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.
Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.
Fixes: 39d1e3340c73 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96a3295c351da82d7af99b2fc004a3cf9f4716a9 ]
Warning on every translated mtd partition results in excessive log noise
if this driver is loaded:
nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
nand: Macronix MX30LF1G18AC
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
read_bbt: found bbt at block 1023
10 fixed-partitions partitions found on MTD device mt7621-nand
Creating 10 MTD partitions on "mt7621-nand":
0x000000000000-0x000000080000 : "Bootloader"
mtdblock: MTD device 'Bootloader' is NAND, please consider using UBI block devices instead.
0x000000080000-0x000000100000 : "Config"
mtdblock: MTD device 'Config' is NAND, please consider using UBI block devices instead.
0x000000100000-0x000000140000 : "Factory"
mtdblock: MTD device 'Factory' is NAND, please consider using UBI block devices instead.
0x000000140000-0x000002000000 : "Kernel"
mtdblock: MTD device 'Kernel' is NAND, please consider using UBI block devices instead.
0x000000540000-0x000002000000 : "ubi"
mtdblock: MTD device 'ubi' is NAND, please consider using UBI block devices instead.
0x000002140000-0x000004000000 : "Kernel2"
mtdblock: MTD device 'Kernel2' is NAND, please consider using UBI block devices instead.
0x000004000000-0x000004100000 : "wwan"
mtdblock: MTD device 'wwan' is NAND, please consider using UBI block devices instead.
0x000004100000-0x000005100000 : "data"
mtdblock: MTD device 'data' is NAND, please consider using UBI block devices instead.
0x000005100000-0x000005200000 : "rom-d"
mtdblock: MTD device 'rom-d' is NAND, please consider using UBI block devices instead.
0x000005200000-0x000005280000 : "reserve"
mtdblock: MTD device 'reserve' is NAND, please consider using UBI block devices instead.
mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
This is more likely to annoy than to help users of embedded distros where
this driver is enabled by default. Making the blockdevs available does
not imply that they are in use, and warning about bootloader partitions
or other devices which obviously never will be mounted is more confusing
than helpful.
Move the warning to open(), where it will be of more use - actually warning
anyone who mounts a file system on NAND using mtdblock.
Fixes: e07403a8c6be ("mtdblock: Warn if added for a NAND device")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220328161108.87757-1-bjorn@mork.no
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a745b51cddafade99aaea1b93aad31e9614e230 ]
All of the resources used by this driver has managed interfaces, so use
them. Otherwise we will get the following splat:
[ 4.472703] denali-nand-pci 0000:00:05.0: timeout while waiting for irq 0x1000
[ 4.474071] denali-nand-pci: probe of 0000:00:05.0 failed with error -5
[ 4.473538] nand: No NAND device found
[ 4.474068] BUG: unable to handle page fault for address: ffffc90005000410
[ 4.475169] #PF: supervisor write access in kernel mode
[ 4.475579] #PF: error_code(0x0002) - not-present page
[ 4.478362] RIP: 0010:iowrite32+0x9/0x50
[ 4.486068] Call Trace:
[ 4.486269] <IRQ>
[ 4.486443] denali_isr+0x15b/0x300 [denali]
[ 4.486788] ? denali_direct_write+0x50/0x50 [denali]
[ 4.487189] __handle_irq_event_percpu+0x161/0x3b0
[ 4.487571] handle_irq_event+0x7d/0x1b0
[ 4.487884] handle_fasteoi_irq+0x2b0/0x770
[ 4.488219] __common_interrupt+0xc8/0x1b0
[ 4.488549] common_interrupt+0x9a/0xc0
Fixes: 93db446a424c ("mtd: nand: move raw NAND related code to the raw/ subdir")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220411125808.958276-1-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a4f9dd55c5e1bb951db6f1dee20e62e0103f3438 ]
Read From Cache Quad IO (EBH) uses 2 dummy bytes on this chip according
to page 23 of the datasheet[0].
[0]: https://www.gigadevice.com/datasheet/gd5f1gq5xexxg/
Fixes: 469b99248985 ("mtd: spinand: gigadevice: Support GD5F1GQ5UExxG")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-2-gch981213@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
|
|
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
|
|
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
[0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents
Fixes: 98dea8d71931 ("mtd: nand: mtk: Support MT7622 NAND flash controller.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fixes for various memory issues
UBI:
- Fix for a race condition in cdev ioctl handler
UBIFS:
- Fixes for O_TMPFILE and whiteout handling
- Fixes for various memory issues"
* tag 'for-linus-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: rename_whiteout: correct old_dir size computing
jffs2: fix memory leak in jffs2_scan_medium
jffs2: fix memory leak in jffs2_do_mount_fs
jffs2: fix use-after-free in jffs2_clear_xattr_subsystem
fs/jffs2: fix comments mentioning i_mutex
ubi: fastmap: Return error code if memory allocation fails in add_aeb()
ubifs: Fix to add refcount once page is set private
ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock()
ubifs: setflags: Make dirtied_ino_d 8 bytes aligned
ubifs: Rectify space amount budget for mkdir/tmpfile operations
ubifs: Fix 'ui->dirty' race between do_tmpfile() and writeback work
ubifs: Rename whiteout atomically
ubifs: Add missing iput if do_tmpfile() failed in rename whiteout
ubifs: Fix wrong number of inodes locked by ui_mutex in ubifs_inode comment
ubifs: Fix deadlock in concurrent rename whiteout and inode writeback
ubifs: rename_whiteout: Fix double free for whiteout_ui->data
ubi: Fix race condition between ctrl_cdev_ioctl and ubi_cdev_ioctl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
|
|
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
|
|
Pull block updates from Jens Axboe:
- BFQ cleanups and fixes (Yu, Zhang, Yahu, Paolo)
- blk-rq-qos completion fix (Tejun)
- blk-cgroup merge fix (Tejun)
- Add offline error return value to distinguish it from an IO error on
the device (Song)
- IO stats fixes (Zhang, Christoph)
- blkcg refcount fixes (Ming, Yu)
- Fix for indefinite dispatch loop softlockup (Shin'ichiro)
- blk-mq hardware queue management improvements (Ming)
- sbitmap dead code removal (Ming, John)
- Plugging merge improvements (me)
- Show blk-crypto capabilities in sysfs (Eric)
- Multiple delayed queue run improvement (David)
- Block throttling fixes (Ming)
- Start deprecating auto module loading based on dev_t (Christoph)
- bio allocation improvements (Christoph, Chaitanya)
- Get rid of bio_devname (Christoph)
- bio clone improvements (Christoph)
- Block plugging improvements (Christoph)
- Get rid of genhd.h header (Christoph)
- Ensure drivers use appropriate flush helpers (Christoph)
- Refcounting improvements (Christoph)
- Queue initialization and teardown improvements (Ming, Christoph)
- Misc fixes/improvements (Barry, Chaitanya, Colin, Dan, Jiapeng,
Lukas, Nian, Yang, Eric, Chengming)
* tag 'for-5.18/block-2022-03-18' of git://git.kernel.dk/linux-block: (127 commits)
block: cancel all throttled bios in del_gendisk()
block: let blkcg_gq grab request queue's refcnt
block: avoid use-after-free on throttle data
block: limit request dispatch loop duration
block/bfq-iosched: Fix spelling mistake "tenative" -> "tentative"
sr: simplify the local variable initialization in sr_block_open()
block: don't merge across cgroup boundaries if blkcg is enabled
block: fix rq-qos breakage from skipping rq_qos_done_bio()
block: flush plug based on hardware and software queue order
block: ensure plug merging checks the correct queue at least once
block: move rq_qos_exit() into disk_release()
block: do more work in elevator_exit
block: move blk_exit_queue into disk_release
block: move q_usage_counter release into blk_queue_release
block: don't remove hctx debugfs dir from blk_mq_exit_queue
block: move blkcg initialization/destroy into disk allocation/release handler
sr: implement ->free_disk to simplify refcounting
sd: implement ->free_disk to simplify refcounting
sd: delay calling free_opal_dev
sd: call sd_zbc_release_disk before releasing the scsi_device reference
...
|
|
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Avoid random build errors with architectures which do not select
HAS_IOMEM by depending on it in Kconfig.
This fixes the following warning:
/home/mraynal/0day/gcc-11.2.0-nolibc/s390-linux/bin/s390-linux-ld:
drivers/mtd/nand/ecc-mxic.o: in function `mxic_ecc_probe':
ecc-mxic.c:(.text+0x2244): undefined reference to `devm_platform_ioremap_resource'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220314152336.75447-1-miquel.raynal@bootlin.com
|
|
Don't populate the read-only arrays possible_strength and
spare_size on the stack but instead make them static
const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220307230940.169235-1-colin.i.king@gmail.com
|
|
The AM65x HyperBus controller is only present on Texas Instruments AM65x
SoCs. Hence add a dependency on ARCH_K3, to prevent asking the user
about this driver when configuring a kernel without support for the
Texas Instruments Inc. K3 multicore SoC architecture.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/9fd6b975adba710158f28aa603cf87a6d189a418.1646655894.git.geert+renesas@glider.be
|
|
partid and partname debugfs files were used just by SPI NOR, but they were
replaced by sysfs entries. Since these debugfs files are no longer used in
mtd, remove dead code. The directory is kept as it is used by nandsim,
mtdswap and docg3.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220225144656.634682-1-tudor.ambarus@microchip.com
|
|
While calculating speed during mtd_speedtest, the time interval
(i.e., start - finish) is rounded off to the nearest milliseconds by
ignoring the fractional part. This leads to miscalculation of speed.
The miscalculation is more visible while running speed test on small
partition sizes(i.e., when partition size is equal to eraseblock size or
twice the eraseblock size) at higher spi frequencies.
For e.g., while calculating eraseblock read speed for a mtd partition with
size equal to the eraseblock size(i.e., 64KiB) the eraseblock read time
interval comes out to be 966490 nanosecond. This is then converted to
millisecond(i.e., 0.966 msec.). The integer part (i.e., 0 msec) of the
value is considered and the fractional part (i.e., 0.966) is ignored,for
calculating the eraseblock read speed. So the reported eraseblock read
speed is 0 KiB/s, which is incorrect.
There are two approaches to fix this issue.
First approach will be to keep the time interval in millisecond. and round
up the integer value, with this approach the 0.966msec time interval in the
above example will be rounded up to 1msec and this value is used for
calculating the speed. Downside of this approach is that the reported speed
is still not accurate.
Second approach will be to convert the time interval to microseconds
instead of milliseconds, with this approach the 966490 nanosecond time
interval in the above example will be converted t0 966.490usec and this
value is used for calculating the speed. As compared to the current
implementation and the suggested First approach, this approach will report
a more accurate speed. Downside of this approach is that, in future if the
mtd size is too large then the u64 variable, that holds the number of
bytes, might overflow.
In this patch we have gone with the second approach as this reports a more
accurate speed. With this approach the eraseblock read speed in the above
example comes out to be 132505 KiB/s when the spi clock is configured at
150Mhz.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220208103905.13354-1-amit.kumar-mahapatra@xilinx.com
|
|
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Co-developed-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn
|
|
Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220303123431.3170-1-hanyihao@vivo.com
|
|
Even if SPI_NOR_NO_ERASE was set, one could still send erase opcodes
to the flash. It is not recommended to send unsupported opcodes to
flashes. Fix the logic and do not set mtd->_erase when SPI_NOR_NO_ERASE
is specified. With this users will not be able to issue erase opcodes to
flashes and instead they will recive an -ENOTSUPP error.
Fixes: b199489d37b2 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220228163334.277730-1-tudor.ambarus@microchip.com
|
|
The root of the problem is that we are selecting symbols that have
dependencies. This can cause random configurations that can fail.
The cleanest solution is to avoid using select.
This driver uses interfaces from the OMAP_GPMC driver so we have to
depend on it instead.
Fixes: 4cd335dae3cf ("mtd: rawnand: omap2: Prevent invalid configuration and build error")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/linux-mtd/20220219193600.24892-1-rogerq@kernel.org
|
|
We need the char-misc fixes in here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.17-rc6 for reported issues.
The majority of these are IIO fixes for small things, and the other
two are a mvmem and mtd core conflict fix.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
iio: Fix error handling for PM
iio: addac: ad74413r: correct comparator gpio getters mask usage
iio: addac: ad74413r: use ngpio size when iterating over mask
iio: addac: ad74413r: Do not reference negative array offsets
iio: adc: men_z188_adc: Fix a resource leak in an error handling path
iio: frequency: admv1013: remove the always true condition
iio: accel: fxls8962af: add padding to regmap for SPI
iio:imu:adis16480: fix buffering for devices with no burst mode
iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
iio: adc: tsc2046: fix memory corruption by preventing array overflow
|
|
As we have deleted some flag, lets renumber them so there are no holes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-33-michael@walle.cc
|
|
Now that there is almost no special case code left in
spi_nor_sr_ready(), the return check looks odd. Move the function call
closer to the return code checking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-32-michael@walle.cc
|
|
Drop the generic spi_nor prefix for all the spansion functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-31-michael@walle.cc
|
|
Now that all functions using that flag are local to the spansion module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-30-michael@walle.cc
|
