| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 3ce17cd2b94907f6d91b81b32848044b84c97606 ]
SMATCH detected a potential buffer overflow in the manipulation of
hwmon_attributes array inside the scmi_hwmon_probe function:
drivers/hwmon/scmi-hwmon.c:226
scmi_hwmon_probe() error: buffer overflow 'hwmon_attributes' 6 <= 9
Fix it by statically declaring the size of the array as the maximum
possible as defined by hwmon_max define.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20200715121338.GA18761@e119603-lin.cambridge.arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a03746c8baf82e1616f05a1a716d34378dcf780 ]
Stefan Dietrich reports invalid temperature source messages on Asus Formula
XII Z490.
nct6775 nct6775.656: Invalid temperature source 28 at index 0,
source register 0x100, temp register 0x73
Debugging suggests that temperature source 28 reports the CPU temperature.
Let's assume that temperature sources 28 and 29 reflect "PECI Agent {0,1}
Calibration", similar to other chips of the series.
Reported-by: Stefan Dietrich <roots@gmx.de>
Cc: Stefan Dietrich <roots@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d1d41c075a1a54ba03370e268171fec20e06563 ]
Issue:
When PEC is enabled, binding adm1272 to the adm1275 would
fail due to PEC error. See below:
adm1275: probe of xxxx failed with error -74
Diagnosis:
Per the datasheet of adm1272, adm1278, adm1293 and amd1294,
PMON_CONFIG (0xd4) is 16bits wide. On the other hand,
PMON_CONFIG (0xd4) for adm1275 is 8bits wide. The driver should not
assume everything is 8bits wide and read only 8bits from it.
Solution:
If it is adm1272, adm1278, adm1293 and adm1294, use i2c_read_word.
Else, use i2c_read_byte
Testing:
Binding adm1272 to the driver.
The change is only tested on adm1272.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20200709040612.3977094-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc4071aafcf4d0535ee423b69167696d6c03207d ]
aspeed_create_fan() reads a pwm_port value using of_property_read_u32().
If pwm_port will be more than ARRAY_SIZE(pwm_port_params), there will be
a buffer overflow in
aspeed_create_pwm_port()->aspeed_set_pwm_port_enable(). The patch fixes
the potential buffer overflow.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20200703111518.9644-1-novikov@ispras.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c66ef39eb27fe123ee05082b90eb2985c33c7715 upstream.
It has been observed that Toshiba DT01ACA family drives have
WRITE FPDMA QUEUED command timeouts and sometimes just freeze until
power-cycled under heavy write loads when their temperature is getting
polled in SCT mode. The SMART mode seems to be fine, though.
Let's make sure we don't use SCT mode for these drives then.
While only the 3 TB model was actually caught exhibiting the problem let's
play safe here to avoid data corruption and extend the ban to the whole
family.
Fixes: 5b46903d8bf3 ("hwmon: Driver for disk and solid state drives with temperature sensors")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Link: https://lore.kernel.org/r/0cb2e7022b66c6d21d3f189a12a97878d0e7511b.1595075458.git.mail@maciej.szmigiero.name
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14b0e83dc4f1e52b94acaeb85a18fd7fdd46d2dc upstream.
This patch fixes a bug which does not let FAN mode to be changed from
sysfs(pwm1_enable). i.e pwm1_enable can not be set to 3, it will always
remain at 0.
This is caused because the device driver handles the result of
"read_u8_from_i2c(client, REG_FAN_CONF1, &conf_reg)" incorrectly. The
driver thinks an error has occurred if the (result != 0). This has been
fixed by changing the condition to (result < 0).
Signed-off-by: Vishwas M <vishwas.reddy.vr@gmail.com>
Link: https://lore.kernel.org/r/20200707142747.118414-1-vishwas.reddy.vr@gmail.com
Fixes: 9df7305b5a86 ("hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4c8af4c2a226fc9c25e1decbd26fdab1b0993ee upstream.
Commit 16358542f32f ("hwmon: (pmbus) Implement multi-phase support")
added support for multi-phase pmbus devices. However, when calling
pmbus_add_sensor() for fans, the patch swapped the `page` and `reg`
attributes. As a result, the fan speeds were reported as 0 RPM on my device.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Fixes: 16358542f32f ("hwmon: (pmbus) Implement multi-phase support")
Cc: stable@vger.kernel.org # v5.7+
Link: https://lore.kernel.org/r/449bc9e6c0e4305581e45905ce9d043b356a9932.1592904387.git.jan.kundrat@cesnet.cz
[groeck: Fixed references to offending commit]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8b97f9922211c44a739c5cbd9502ecbb9f17f6d1 ]
Although it rarely happens, we should call free_capabilities()
if error happens after read_capabilities() to free allocated strings.
Fixes: de584afa5e188 ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Link: https://lore.kernel.org/r/20200625043242.31175-1-misono.tomohiro@jp.fujitsu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 016983d138cbe99a5c0aaae0103ee88f5300beb3 ]
Per the datasheet for max6697, OVERT mask and ALERT mask are different.
For example, the 7th bit of OVERT is the local channel but for alert
mask, the 6th bit is the local channel. Therefore, we can't apply the
same mask for both registers. In addition to that, the max6697 driver
is supposed to be compatibale with different models. I manually went over
all the listed chips and made sure all chip types have the same layout.
Testing;
mask value of 0x9 should map to 0x44 for ALERT and 0x84 for OVERT.
I used iotool to read the reg value back to verify. I only tested this
change on max6581.
Reference:
https://datasheets.maximintegrated.com/en/ds/MAX6581.pdf
https://datasheets.maximintegrated.com/en/ds/MAX6697.pdf
https://datasheets.maximintegrated.com/en/ds/MAX6699.pdf
Signed-off-by: Chu Lin <linchuyuan@google.com>
Fixes: 5372d2d71c46e ("hwmon: Driver for Maxim MAX6697 and compatibles")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 279f0b3a4b80660fba6faadc2ca2fa426bf3f7e9 upstream.
Add support for retrieving Tdie and Tctl on AMD Renoir (4000-series
Ryzen CPUs).
It appears SMU offsets for reading current/voltage and CCD temperature
have changed for this generation (reads from currently used offsets
yield zeros), so those features cannot be enabled so trivially.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200510204842.2603-3-amonakov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When tsi-as-adc is configured it is possible for in7[0123]_input read to
return an incorrect value if a concurrent read to in[456]_input is
performed. This is caused by a concurrent manipulation of the mux
channel without proper locking as hwmon and mfd use different locks for
synchronization.
Switch hwmon to use the same lock as mfd when accessing the TSI channel.
Fixes: 4f16cab19a3d5 ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Samu Nuutamo <samu.nuutamo@vincit.fi>
[rebase to current master, reword commit message slightly]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The format of temperature limitation registers are 8-bit 2's complement
and the range is -128~127.
Converts the reading value to signed char to fix the incorrect range
of temperature limitation registers.
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When nct7904 power up, it compares current sensor readings against the
default threshold immediately. This results in false alarms on startup.
Read all SMI status registers in probe function to clear the alarms.
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
[groeck: Reworded description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If SCT is supported but SCT data tables are not, the driver unnecessarily
tries to fall back to SMART. Use SCT without data tables instead in this
situation.
Fixes: 5b46903d8bf3 ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The jc42 driver passes I2C client's name as hwmon device name. In case
of device tree probed devices this ends up being part of the compatible
string, "jc-42.4-temp". This name contains hyphens and the hwmon core
doesn't like this:
jc42 2-0018: hwmon: 'jc-42.4-temp' is not a valid name attribute, please fix
This changes the name to "jc42" which doesn't have any illegal
characters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200417092853.31206-1-s.hauer@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix the following sparse warning:
drivers/hwmon/k10temp.c:189:12: warning: symbol 'k10temp_temp_label' was
not declared. Should it be static?
drivers/hwmon/k10temp.c:202:12: warning: symbol 'k10temp_in_label' was
not declared. Should it be static?
drivers/hwmon/k10temp.c:207:12: warning: symbol 'k10temp_curr_label' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200409084502.42126-1-yanaijie@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Holger Hoffstätte observed that Samsung 850 Pro may return invalid
temperatures for a short period of time after resume. Return -ENODATA
to userspace if this is observed.
Fixes: 5b46903d8bf3 ("hwmon: Driver for disk and solid state drives with temperature sensors")
Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The addition of the support for reading the temperature of ATA drives as
per commit 5b46903d8bf3 ("hwmon: Driver for disk and solid state drives
with temperature sensors") lists in the respective Kconfig section the
name of the module to be optionally built as "satatemp".
However, building the kernel modules with "CONFIG_SENSORS_DRIVETEMP=m",
does not generate a file named "satatemp.ko".
Instead, the rest of the original commit uses the term "drivetemp" and
a file named "drivetemp.ko" ends up in the kernel's modules directory.
This file has the right ingredients:
$ strings /path/to/drivetemp.ko | grep ^description
description=Hard drive temperature monitor
and modprobing it produces the expected result:
# drivetemp is not loaded
$ sensors -u drivetemp-scsi-4-0
Specified sensor(s) not found!
$ sudo modprobe drivetemp
$ sensors -u drivetemp-scsi-4-0
drivetemp-scsi-4-0
Adapter: SCSI adapter
temp1:
temp1_input: 35.000
temp1_max: 60.000
temp1_min: 0.000
temp1_crit: 70.000
temp1_lcrit: -40.000
temp1_lowest: 20.000
temp1_highest: 36.000
Fix Kconfig by referring to the true name of the module.
Fixes: 5b46903d8bf3 ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Ann T Ropea <bedhanger@gmx.de>
Link: https://lore.kernel.org/r/20200406235521.185309-1-bedhanger@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
I2C chip IDs need to reflect chip names, not chip functionality.
Fixes: f621d61fd59f ("hwmon: (pmbus) add support for 2nd Gen Renesas digital multiphase")
Cc: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
For security reasons I stopped using gmail account and kernel address is
now up-to-date alias to my personal address.
People periodically send me emails to address which they found in source
code of drivers, so this change reflects state where people can contact
me.
[ Added .mailmap entry as per Joe Perches - Linus ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200307104237.8199-1-pali@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
|
|
Conflicts:
arch/x86/events/intel/uncore.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131509.859324598@linutronix.de
|
|
Extend the isl68137 driver to provide support for 2nd generation Renesas
digital multiphase voltage regulators.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Link: https://lore.kernel.org/r/62c000adf0108aeb65d3f275f28eb26b690384aa.1584720563.git.grantpeltier93@gmail.com
[groeck: Adjusted for new PMBus API function parameters]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There is an additional CCIN for the IBM CFFPS that may be classifed as
either version one or version two, based upon the rest of the bits of
the CCIN. Add support for it in the version detection.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1583948590-17220-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
nct7904d supports 12 fan tachometers input and 13 temperatures
(TEMP_CH1~4 and LTD + DTS TCPU1~8), fix the quantity for fan & temp
attributes.
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20200312024934.3533-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add a "adi,pwm-active-state" device-tree property to allow hardware
designs to use inverted logic on the PWM output.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: dev_err -> dev_warn]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Added support for reading DTS properties to set attenuators on
device probe for the ADT7473, ADT7475, ADT7476, and ADT7490.
Signed-off-by: Logan Shaw <logan.shaw@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Continuation line formatting; dev_err -> dev_warn]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add the of_match_table.
Signed-off-by: Henry Shen <henry.shen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200212030615.28537-3-henry.shen@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TPS53647 and TPS53667 are single channel, Step-Down Buck Controllers.
TPS53647 supports 4 phases, TPS53667 supports 6 phases.
The chips do not support per-phase output telemetry.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TPS53681 is a dual-channel multiphase step-down controller
supporting per-phase and per-channel output telemetry.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
All chips of this series with published datasheets support IIN, PIN, and
STATUS_INPUT PMBus commands. Per TI Power Management Forum, "TPS53679 and
TPS53681 have the same PMBus command set". There is no reason to believe
that this does not apply to TPS53688. Let's assume that this is correct
and add support for IIN, PIN, and STATUS_INPUT to TPS53679 and TPS53688
to simplify adding support for more chips of the same series.
At the same time, drop reporting VIN on channel 2. On chips with published
datasheets this voltage is identical to the voltage reported on channel 1,
and there is no reason to believe that this is different for TPS53679 and
TPS53888.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Chip specific support will be needed in the driver to be able to
support additional chips of the same series. Add support for it
to the driver.
To simplify adding support for more chips, call identification code
from the probe function. This lets us use a single structure for common
elements of struct pmbus_driver_info, thus reducing code size as support
for more chips is added.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Some PMBus chips support multiple phases, and report telemetry such
as input current, output current, or temperature for each phase.
Add support for such chips to the PMBus core.
Start with a maximum of 8 phases per page, and assume that supported
sensors per phase are similar for all pages. Only support per-phase
telemetry attributes, no limits or alarms.
As part of this patch, set the initial page variable to 0xff to ensure
that the page is updated when the first page command is issued. Also
only issue page commands if the chip supports more than one page.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In preparation for multi-phase support, add 'phase' parameter to read_word
and set_page functions. Actual multi-phase support will be added in
a subsequent patch.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Recent PMBus versions added IC_DEVICE_ID and IC_DEVICE_REV commands as
additional means to identify the chip. Add command definitions to
pmbus.h include file.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211234237.GA26971@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use a bit map to describe if temperature channels are supported,
and use it for all temperature channels. Use a separate flag,
independent of Tdie support, to indicate if the system is running
on a Ryzen CPU.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Traditionally, the temperature displayed by k10temp was Tctl.
On Family 17h CPUs, Tdie was displayed instead. To reduce confusion,
Tctl was added later as second temperature. This resulted in Tdie
being reported as temp1_input, and Tctl as temp2_input. This is
different to non-Ryzen CPUs, where Tctl is displayed as temp1_input.
Swap temp1_input and temp2_input on Family 17h CPUs, such that Tctl
is now reported as temp1_input and Tdie is reported as temp2_input,
to align with other CPUs, streamline the code, and make it less
confusing. Coincidentally, this also aligns the code with its
documentation, which states that Tdie is reported as temp2_input.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTC2972, LTC2979, LTC3884, LTC3889, LTC7880, LTM4664, LTM4677,
LTM4678, LTM4680, LTM4700.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1581032654-4330-1-git-send-email-michael-a1.jones@analog.com
[groeck: Fixed checkpatch issues (long lines, whitespace)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The purpose of this IP Core is to control the fan used for the cooling of a
Xilinx Zynq Ultrascale+ MPSoC without the need of any external temperature
sensors. To achieve this, the IP core uses the PL SYSMONE4 primitive to
obtain the PL temperature and, based on those readings, it then outputs
a PWM signal to control the fan rotation accordingly.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191009102806.262241-1-nuno.sa@analog.com
[groeck: adi,pulses-per-revolution -> pulses-per-revolution;
dropped unused 'res' from probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This is only called from adt7462_update_device(). The caller expects it
to return zero on error. I fixed a similar issue earlier in commit
a4bf06d58f21 ("hwmon: (adt7462) ADT7462_REG_VOLT_MAX() should return 0")
but I missed this one.
Fixes: c0b4e3ab0c76 ("adt7462: new hwmon driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Link: https://lore.kernel.org/r/20200303101608.kqjwfcazu2ylhi2a@kili.mountain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Provide read_word_data() callback for overvoltage and undervoltage
output readouts conversion. These registers are presented in
'slinear11' format, while default conversion for 'vout' class for the
devices is 'vid'. It is resulted in wrong conversion in pmbus_reg2data()
for in{3-4}_lcrit and in{3-4}_crit attributes.
)
Fixes: aaafb7c8eb1c ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200224225202.19576-1-vadimp@mellanox.com
[gropeck: Adjusted to mainline PMBus API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Loading the driver on a system with W83627DHG-P crashes as follows.
w83627ehf: Found W83627DHG-P chip at 0x290
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 0 PID: 604 Comm: sensors Not tainted 5.6.0-rc2-00055-gca7e1fd1026c #29
Hardware name: /D425KT, BIOS MWPNT10N.86A.0132.2013.0726.1534 07/26/2013
RIP: 0010:w83627ehf_read_string+0x27/0x70 [w83627ehf]
Code: [... ]
RSP: 0018:ffffb95980657df8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff96caaa7f5218 RCX: 0000000000000000
RDX: 0000000000000015 RSI: 0000000000000001 RDI: ffff96caa736ec08
RBP: 0000000000000000 R08: ffffb95980657e20 R09: 0000000000000001
R10: ffff96caaa635cc0 R11: 0000000000000000 R12: ffff96caa9f7cf00
R13: ffff96caa9ec3d00 R14: ffff96caa9ec3d28 R15: ffff96caa9ec3d40
FS: 00007fbc7c4e2740(0000) GS:ffff96caabc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000129d58000 CR4: 00000000000006f0
Call Trace:
? cp_new_stat+0x12d/0x160
hwmon_attr_show_string+0x37/0x70 [hwmon]
dev_attr_show+0x14/0x50
sysfs_kf_seq_show+0xb5/0x1b0
seq_read+0xcf/0x460
vfs_read+0x9b/0x150
ksys_read+0x5f/0xe0
do_syscall_64+0x48/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
...
Temperature labels are not always present. Adjust sysfs attribute
visibility accordingly.
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Dr. David Alan Gilbert <linux@treblig.org>
Fixes: 266cd5835947 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Damien Le Moal reports a lockdep splat with the acpi_power_meter,
observed with Linux v5.5 and later.
======================================================
WARNING: possible circular locking dependency detected
5.6.0-rc2+ #629 Not tainted
------------------------------------------------------
python/1397 is trying to acquire lock:
ffff888619080070 (&resource->lock){+.+.}, at: show_power+0x3c/0xa0 [acpi_power_meter]
but task is already holding lock:
ffff88881643f188 (kn->count#119){++++}, at: kernfs_seq_start+0x6a/0x160
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (kn->count#119){++++}:
__kernfs_remove+0x626/0x7e0
kernfs_remove_by_name_ns+0x41/0x80
remove_attrs+0xcb/0x3c0 [acpi_power_meter]
acpi_power_meter_notify+0x1f7/0x310 [acpi_power_meter]
acpi_ev_notify_dispatch+0x198/0x1f3
acpi_os_execute_deferred+0x4d/0x70
process_one_work+0x7c8/0x1340
worker_thread+0x94/0xc70
kthread+0x2ed/0x3f0
ret_from_fork+0x24/0x30
-> #0 (&resource->lock){+.+.}:
__lock_acquire+0x20be/0x49b0
lock_acquire+0x127/0x340
__mutex_lock+0x15b/0x1350
show_power+0x3c/0xa0 [acpi_power_meter]
dev_attr_show+0x3f/0x80
sysfs_kf_seq_show+0x216/0x410
seq_read+0x407/0xf90
vfs_read+0x152/0x2c0
ksys_read+0xf3/0x1d0
do_syscall_64+0x95/0x1010
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(kn->count#119);
lock(&resource->lock);
lock(kn->count#119);
lock(&resource->lock);
*** DEADLOCK ***
4 locks held by python/1397:
#0: ffff8890242d64e0 (&f->f_pos_lock){+.+.}, at: __fdget_pos+0x9b/0xb0
#1: ffff889040be74e0 (&p->lock){+.+.}, at: seq_read+0x6b/0xf90
#2: ffff8890448eb880 (&of->mutex){+.+.}, at: kernfs_seq_start+0x47/0x160
#3: ffff88881643f188 (kn->count#119){++++}, at: kernfs_seq_start+0x6a/0x160
stack backtrace:
CPU: 10 PID: 1397 Comm: python Not tainted 5.6.0-rc2+ #629
Hardware name: Supermicro Super Server/X11DPL-i, BIOS 3.1 05/21/2019
Call Trace:
dump_stack+0x97/0xe0
check_noncircular+0x32e/0x3e0
? print_circular_bug.isra.0+0x1e0/0x1e0
? unwind_next_frame+0xb9a/0x1890
? entry_SYSCALL_64_after_hwframe+0x49/0xbe
? graph_lock+0x79/0x170
? __lockdep_reset_lock+0x3c0/0x3c0
? mark_lock+0xbc/0x1150
__lock_acquire+0x20be/0x49b0
? mark_held_locks+0xe0/0xe0
? stack_trace_save+0x91/0xc0
lock_acquire+0x127/0x340
? show_power+0x3c/0xa0 [acpi_power_meter]
? device_remove_bin_file+0x10/0x10
? device_remove_bin_file+0x10/0x10
__mutex_lock+0x15b/0x1350
? show_power+0x3c/0xa0 [acpi_power_meter]
? show_power+0x3c/0xa0 [acpi_power_meter]
? mutex_lock_io_nested+0x11f0/0x11f0
? lock_downgrade+0x6a0/0x6a0
? kernfs_seq_start+0x47/0x160
? lock_acquire+0x127/0x340
? kernfs_seq_start+0x6a/0x160
? device_remove_bin_file+0x10/0x10
? show_power+0x3c/0xa0 [acpi_power_meter]
show_power+0x3c/0xa0 [acpi_power_meter]
dev_attr_show+0x3f/0x80
? memset+0x20/0x40
sysfs_kf_seq_show+0x216/0x410
seq_read+0x407/0xf90
? security_file_permission+0x16f/0x2c0
vfs_read+0x152/0x2c0
Problem is that reading an attribute takes the kernfs lock in the kernfs
code, then resource->lock in the driver. During an ACPI notification, the
opposite happens: The resource lock is taken first, followed by the kernfs
lock when sysfs attributes are removed and re-created. Presumably this is
now seen due to some locking related changes in kernfs after v5.4, but it
was likely always a problem.
Fix the problem by not blindly acquiring the lock in the notification
function. It is only needed to protect the various update functions.
However, those update functions are called anyway when sysfs attributes
are read. This means that we can just stop calling those functions from
the notifier, and the resource lock in the notifier function is no longer
needed.
That leaves two situations:
First, METER_NOTIFY_CONFIG removes and re-allocates capability strings.
While it did so under the resource lock, _displaying_ those strings was not
protected, creating a race condition. To solve this problem, selectively
protect both removal/creation and reporting of capability attributes with
the resource lock.
Second, removing and re-creating the attribute files is no longer protected
by the resource lock. That doesn't matter since access to each individual
attribute is protected by the kernfs lock. Userspace may get messed up if
attributes disappear and reappear under its nose, but that is not different
than today, and there is nothing we can do about it without major driver
restructuring.
Last but not least, when removing the driver, remove attribute functions
first, then release capability strings. This avoids yet another race
condition.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: stable@vger.kernel.org # v5.5+
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Make sure that the driver compatible strings matches the binding by
removing the space between the manufacturer and model.
Fixes: aaafb7c8eb1c ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200212092426.24012-1-johan@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bbb49 ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
|
|
The most notable change is DEFINE_SHOW_ATTRIBUTE macro split in
seq_file.h.
Conversion rule is:
llseek => proc_lseek
unlocked_ioctl => proc_ioctl
xxx => proc_xxx
delete ".owner = THIS_MODULE" line
[akpm@linux-foundation.org: fix drivers/isdn/capi/kcapi_proc.c]
[sfr@canb.auug.org.au: fix kernel/sched/psi.c]
Link: http://lkml.kernel.org/r/20200122180545.36222f50@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191225172546.GB13378@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
