| Age | Commit message (Collapse) | Author |
|---|
|
Suspend the FB console during driver shutdown the same way this is done
during system resume. This should prevent any HPD event to trigger a new
FB probe/modeset cycle happening in parallel with the display HW
disable/uninitialize steps.
A preceding FB HPD event handling may be still pending, resulting in a
probe/modeset like the above, these will be prevented by a later change
in this patchset.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-6-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
The only purpose of intel_hpd_poll_disable() during driver loading and
system resume - at which point polling should be disabled anyway, except
for connectors in an IRQ storm, for which the polling will stay enabled -
is to force-detect all the connectors. However this detection in
i915_hpd_poll_init_work() depends on drm.mode_config.poll_enabled, which
will get set in drm_kms_helper_poll_init(), possibly after
i915_hpd_poll_init_work() is scheduled. Hence the initial detection of
connectors during driver loading may not happen.
Fix the above by moving intel_hpd_poll_disable() after
i915_hpd_poll_init_work(), the proper place anyway for doing the above
detection after all the HW initialization steps are complete. Change the
order the same way during system resume as well. The above race
condition shouldn't matter here - as drm.mode_config.poll_enabled will
be set - but the detection should happen here as well after the HW init
steps are done.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-5-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
Deinitialize audio during driver unload after disabling polling. This is
in preparation to do all the display HW init/deinit steps at a point
where no HPD IRQ or polling initiated connector detection or modeset can
change the HW state. This may still happen here via an HPD IRQ ->
hotplug detection work or a connector sysfs (state/detect) access, but
these will be prevented by later changes in this patchset.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-4-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
If an HPD IRQ storm is detected on a connector during driver loading or
system suspend/resume - disabling the IRQ and switching to polling - the
polling may get disabled too early - before the intended 2 minute
HPD_STORM_REENABLE_DELAY - with the HPD IRQ staying disabled for this
duration. One such sequence is:
Thread#1 Thread#2
intel_display_driver_probe()->
intel_hpd_init()->
(HPD IRQ gets enabled)
. intel_hpd_irq_handler()->
. intel_hpd_irq_storm_detect()
. intel_hpd_irq_setup()->
. (HPD IRQ gets disabled)
. queue_delayed_work(hotplug.hotplug_work)
. ...
. i915_hotplug_work_func()->
. intel_hpd_irq_storm_switch_to_polling()->
. (polling enabled)
.
intel_hpd_poll_disable()->
queue_work(hotplug.poll_init_work)
...
i915_hpd_poll_init_work()->
(polling gets disabled,
HPD IRQ is still disabled)
...
(Connector is neither polled or
detected via HPD IRQs for 2 minutes)
intel_hpd_irq_storm_reenable_work()->
(HPD IRQ gets enabled)
To avoid the above 2 minute state without either polling or enabled HPD
IRQ, leave the connector's polling mode unchanged in
i915_hpd_poll_init_work() if its HPD IRQ got disabled after an IRQ storm
indicated by the connector's HPD_DISABLED pin state.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-3-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
After an HPD IRQ storm on a connector intel_hpd_irq_storm_detect() will
set the connector's HPD pin state to HPD_MARK_DISABLED and the IRQ gets
disabled. Subsequently intel_hpd_irq_storm_switch_to_polling() will
enable polling for these connectors, setting the pin state to
HPD_DISABLED, but only if the connector's base.polled field is set to
DRM_CONNECTOR_POLL_HPD. intel_hpd_irq_storm_reenable_work() will
reenable the IRQ - after 2 minutes - if the pin state is HPD_DISABLED.
The connectors will be created with their base.polled field set to 0,
which gets initialized only later in i915_hpd_poll_init_work() (using
intel_connector::polled). If a storm is detected on a connector after
it's created and IRQs are enabled on it - by intel_hpd_init() - and
before its bease.polled field is initialized in the above work, the
connector's HPD pin will stay in the HPD_MARK_DISABLED state - leaving
the IRQ disabled indefinitely - and polling will not get enabled on it as
intended.
I can't see a reason for initializing base.polled in a delayed manner,
so do this already when creating the connector, to prevent the above
race condition.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-2-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
There is a spelling mistake in a drm_info message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240102092014.3347566-1-colin.i.king@gmail.com
|
|
Remove the unused drm_connector_helper_get_modes_from_ddc()
function. Most drivers should probably have this functionality split to
detect and get modes parts, so the helper is not the best abstraction.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/60eb6b2db16747d3f9c12604b197f33da585c16e.1704473654.git.jani.nikula@intel.com
|
|
Convert mgag200_vga_connector_helper_get_modes() to use struct drm_edid
based functions directly.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/19a453c725fc27bd890f8fc73104f43a376dfce0.1704473654.git.jani.nikula@intel.com
|
|
I/O video memory for the framebuffer supports write-combine caching
mode. Simplify the driver's code that sets up the caching mode.
* Map video memory with ioremap_wc(), which automatically sets up
the PAT entry with write-combine caching.
* Remove the now obsolete call to devm_arch_io_reserve_memtype_wc().
It is only required to mmap the video memory to user space, which the
driver doesn't do.
* According to the PAT documentation, arch_phys_wc_add() is best
called after remapping I/O memory, so move it after ioremap.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105082714.21881-1-tzimmermann@suse.de
|
|
We used to select between MPLLA/B with the following
state->tx[0] & C20_PHY_USE_MPLLB
Since this is used a few places within C20 PLL setting,
let's introduce a helper function to clean up the code
a bit.
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105112243.224199-1-mika.kahola@intel.com
|
|
Return an error code without storing it in an intermediate variable.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/85f8004e-f0c9-42d9-8c59-30f1b4e0b89e@web.de
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
|
|
The kfree() function was called in one case by the
drm_sched_init() function during error handling
even if the passed data structure member contained a null pointer.
This issue was detected by using the Coccinelle software.
Thus adjust a jump target.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/85066512-983d-480c-a44d-32405ab1b80e@web.de
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
|
|
A failure to load the HuC is occasionally observed where the cause is
believed to be a low GT frequency leading to very long load times.
So a) increase the timeout so that the user still gets a working
system even in the case of slow load. And b) report the frequency
during the load to see if that is the cause of the slow down.
Also update the similar code on the GuC load to not use uncore->gt
when there is a local gt available. The two should match, but no need
for unnecessary de-referencing.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240102222202.310495-1-John.C.Harrison@Intel.com
|
|
Copy StutterPeriod from DML2 into DML1 StutterPeriod parameter.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
IGT `amdgpu/amd_color/crtc-lut-accuracy` fails right at the beginning of
the test execution, during atomic check, because DC rejects the
bandwidth state for a fb sizing 64x64. The test was previously working
with the deprecated dc_commit_state(). Now using
dc_validate_with_context() approach, the atomic check needs to perform a
full state validation. Therefore, set fast_validation to false in the
dc_validate_global_state call for atomic check.
Cc: stable@vger.kernel.org
Fixes: b8272241ff9d ("drm/amd/display: Drop dc_commit_state in favor of dc_commit_streams")
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
These chips needs the same fix. This was previously not seen
on then since the AGP aperture expanded the system aperture,
but this showed up again when AGP was disabled.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Other environments don't like the unary minus operator on
an unsigned value.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Use tabs, not spaces.
- Brace and parentheses placement
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
That commit causes NULL pointer dereferences in dmesgs when
running applications using ROCm, including clinfo, blender,
and PyTorch, since v6.6.1. Revert it to fix blender again.
This reverts commit 96c211f1f9ef82183493f4ceed4e347b52849149.
Closes: https://github.com/ROCm/ROCm/issues/2596
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2991
Reviewed-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Kaibo Ma <ent3rm4n@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
gcc prints a warning about a possible array overflow for a couple of
callers of dp_decide_lane_settings() after commit 1b56c90018f0 ("Makefile:
Enable -Wstringop-overflow globally"):
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c: In function 'dp_perform_fixed_vs_pe_training_sequence_legacy':
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: error: 'dp_decide_lane_settings' accessing 4 bytes in a region of size 1 [-Werror=stringop-overflow=]
426 | dp_decide_lane_settings(lt_settings, dpcd_lane_adjust,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
427 | lt_settings->hw_lane_settings, lt_settings->dpcd_lane_settings);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: note: referencing argument 4 of type 'union dpcd_training_lane[4]'
I'm not entirely sure what caused this, but changing the prototype to expect
a pointer instead of an array avoids the warnings.
Fixes: 7727e7b60f82 ("drm/amd/display: Improve robustness of FIXED_VS link training at DP1 rates")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Place define macro expression inside () in power_helpers.c file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Place HDCP_EVENT_TRACE(hdcp, event) macro content inside do while loop
to avoid if-else issues in hdcp_log.h file
v2: fix up build (Alex)
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove braces for single statement if expressions and change comparison
order for hdcp2_execution.c file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix identation inside enum and place expressions in define macros inside
() for hdcp_psp.h file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove braces for single statement if expression for freesync.c file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix identation for hdcp_psp.c file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove braces from single statement if expression in hdcp1_execution.c
file
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The hwmgr->backend, (i.e. data) allocated by kzalloc is not freed in
the error-handling paths of smu7_get_evv_voltages and
smu7_update_edc_leakage_table. However, it did be freed in the
error-handling of phm_initializa_dynamic_state_adjustment_rule_settings,
by smu7_hwmgr_backend_fini. So the lack of free in smu7_get_evv_voltages
and smu7_update_edc_leakage_table is considered a memleak in this patch.
Fixes: 599a7e9fe1b6 ("drm/amd/powerplay: implement smu7 hwmgr to manager asics with smu ip version 7.")
Fixes: 8f0804c6b7d0 ("drm/amd/pm: add edc leakage controller setting")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix the following about iterator use:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1456 kfd_add_peer_prop() warn: iterator used outside loop: 'iolink3'
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Return value of container_of(...) can't be null, so null check is not
required for 'fence'. Hence drop its NULL check.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_fence.c:93 to_amdgpu_amdkfd_fence() warn: can 'fence' even be NULL?
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
kfd_topology.c
Before using list_first_entry, make sure to check that list is not
empty, if list is empty return -ENODATA.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1347 kfd_create_indirect_link_prop() warn: can 'gpu_link' even be NULL?
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1428 kfd_add_peer_prop() warn: can 'iolink1' even be NULL?
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1433 kfd_add_peer_prop() warn: can 'iolink2' even be NULL?
Fixes: 0f28cca87e9a ("drm/amdkfd: Extend KFD device topology to surface peer-to-peer links")
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'amdgpu_ucode_request()'
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c:1404 amdgpu_ucode_request() warn: '*fw' from request_firmware() not released on lines: 1404.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Lijo Lazar <lijo.lazar@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'amdgpu_mca_smu_get_mca_entry()'
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_mca.c:377 amdgpu_mca_smu_get_mca_entry() warn: variable dereferenced before check 'mca_funcs' (see line 368)
357 int amdgpu_mca_smu_get_mca_entry(struct amdgpu_device *adev,
enum amdgpu_mca_error_type type,
358 int idx, struct mca_bank_entry *entry)
359 {
360 const struct amdgpu_mca_smu_funcs *mca_funcs =
adev->mca.mca_funcs;
361 int count;
362
363 switch (type) {
364 case AMDGPU_MCA_ERROR_TYPE_UE:
365 count = mca_funcs->max_ue_count;
mca_funcs is dereferenced here.
366 break;
367 case AMDGPU_MCA_ERROR_TYPE_CE:
368 count = mca_funcs->max_ce_count;
mca_funcs is dereferenced here.
369 break;
370 default:
371 return -EINVAL;
372 }
373
374 if (idx >= count)
375 return -EINVAL;
376
377 if (mca_funcs && mca_funcs->mca_get_mca_entry)
^^^^^^^^^
Checked too late!
Cc: Yang Wang <kevinyang.wang@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This param can help isolating data path issues on new systems in early phase.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the below:
drivers/gpu/drm/amd/amdgpu/atom.c:398 atom_skip_src_int() warn: ignoring unreachable code.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
mod_freesync header file has duplicated copyright boilerplate. Drop the
duplicate.
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's no longer required.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2318
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This was included in gpu_info firmware, move it into the
driver for consistency with other nv1x parts.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2318
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
without PSR
The check for sending the vsc infopacket to the display was gated behind
PSR (Panel Self Refresh) being enabled.
The vsc infopacket also contains the colorimetry (specifically the
container color gamut) information for the stream on modern DP.
PSR is typically only supported on mobile phone eDP displays, thus this
was not getting sent for typical desktop monitors or TV screens.
This functionality is needed for proper HDR10 functionality on DP as it
wants BT2020 RGB/YCbCr for the container color space.
Cc: stable@vger.kernel.org
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Cc: Melissa Wen <mwen@igalia.com>
Fixes: 15f9dfd545a1 ("drm/amd/display: Register Colorspace property for DP and HDMI")
Tested-by: Simon Berz <simon@berz.me>
Tested-by: Xaver Hugl <xaver.hugl@kde.org>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Not needed any more with firmware fixes
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expose sysfs entry mem_busy_percent for GC version
9.4.3 APU system
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Commit 5a028e8f062f ("drm/rockchip: vop2: Add support for rk3588")
introduced a variable which ended up being unused:
rockchip_drm_vop2.c:1688:23: warning: variable ‘if_dclk_rate’ set but not used [-Wunused-but-set-variable]
This has been initially used as part of a formula to compute the clock
dividers, but eventually it has been replaced by static values.
Drop the variable declaration and move its assignment to the comment
block, to serve as documentation of how the constants have been
generated.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105174007.98054-1-cristian.ciocaltea@collabora.com
|
|
It looks that declaration of kunit_get_current_test() was
available in xe_guc_relay.c only with CONFIG_KUNIT enabled.
If CONFIG_KUNIT is disabled we fail with:
In file included from ../include/linux/build_bug.h:5,
from ../include/linux/bitfield.h:10,
from ../drivers/gpu/drm/xe/xe_guc_relay.c:6:
../drivers/gpu/drm/xe/xe_guc_relay.c: In function ‘xe_guc_relay_process_guc2vf’:
../drivers/gpu/drm/xe/xe_guc_relay.c:863:52: error: implicit declaration of function ‘kunit_get_current_test’ [-Werror=implicit-function-declaration]
863 | if (unlikely(!IS_SRIOV_VF(relay_to_xe(relay)) && !kunit_get_current_test()))
| ^~~~~~~~~~~~~~~~~~~~~~
../include/linux/compiler.h:77:42: note: in definition of macro ‘unlikely’
77 | # define unlikely(x) __builtin_expect(!!(x), 0)
| ^
Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: 811fe9f556fc ("drm/xe/guc: Introduce Relay Communication for SR-IOV")
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://lore.kernel.org/r/20240105171947.321-1-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
|
|
The helper is generic, it doesn't use the opaque EDID type struct drm_edid
and is also used by drivers that only support non-probeable displays such
as fixed panels.
These drivers add a list of modes using drm_mode_probed_add() and then set
a preferred mode using the drm_set_preferred_mode() helper.
It seems more logical to have the helper definition in drm_modes.o instead
of drm_edid.o, since the former contains modes helper while the latter has
helpers to manage the EDID information.
Since both drm_edid.o and drm_modes.o object files are built-in the drm.o
object, there are no functional changes. But besides being a more logical
place for this helper, it could also allow to eventually make drm_edid.o
optional and not included in drm.o if only fixed panels must be supported
in a given system.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240102122208.3103597-1-javierm@redhat.com
|
|
WA 14019877138 needed for Graphics 12.70/71 both
V2(Jani):
- Use drm/i915
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103053111.763172-1-tejas.upadhyay@intel.com
|
|
This kunit verifies the mocs registers content
with the KMD programmed values before and after
GT reset.
v2: Remove extra blank lines between the local variables
definitions (Matt Roper)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ruthuvikas Ravikumar <ruthuvikas.ravikumar@intel.com>
Signed-off-by: Janga Rahul Kumar <janga.rahul.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20231222192352.927101-1-janga.rahul.kumar@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
GuC Relay infrastructure is ready, start handling relay messages
from the GuC to unblock testing on the live system.
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://lore.kernel.org/r/20240104222031.277-11-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
|
|
Add few tests to make sure that some negative and normal use
scenarios of the GuC Relay are implemented correctly.
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://lore.kernel.org/r/20240104222031.277-10-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
|
|
We want to use replacement functions in upcoming kunit tests.
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://lore.kernel.org/r/20240104222031.277-9-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
|
|
There are scenarios where SR-IOV Virtual Function (VF) driver will
need to get additional data that is not available over VF MMIO BAR
nor could be queried from the GuC firmware and must be obtained
from the Physical Function (PF) driver.
To allow such communication between VF and PF drivers, GuC supports
set of H2G and G2H actions which allows relaying embedded messages,
that are otherwise opaque for the GuC.
To allow use of this communication mechanism, provide functions for
sending requests and handling replies and placeholder where we will
put handlers for incoming requests.
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://lore.kernel.org/r/20240104222031.277-8-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
|
