summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)Author
2022-04-08Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interruptYake Yang
[ Upstream commit b062a0b9c1dc1ff63094337dccfe1568d5b62023 ] Fix the following kernel oops in btmtksdio_interrrupt [ 14.339134] btmtksdio_interrupt+0x28/0x54 [ 14.339139] process_sdio_pending_irqs+0x68/0x1a0 [ 14.339144] sdio_irq_work+0x40/0x70 [ 14.339154] process_one_work+0x184/0x39c [ 14.339160] worker_thread+0x228/0x3e8 [ 14.339168] kthread+0x148/0x3ac [ 14.339176] ret_from_fork+0x10/0x30 That happened because hdev->power_on is already called before sdio_set_drvdata which btmtksdio_interrupt handler relies on is not properly set up. The details are shown as the below: hci_register_dev would run queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI workqueue_struct to complete the power-on sequeunce and thus hci_power_on may run before sdio_set_drvdata is done in btmtksdio_probe. The hci_dev_do_open in hci_power_on would initialize the device and enable the interrupt and thus it is possible that btmtksdio_interrupt is being called right before sdio_set_drvdata is filled out. When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled , the kernel oops is going to happen because btmtksdio_interrupt access an uninitialized pointer. Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Reviewed-by: Mark Chen <markyawenchen@gmail.com> Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-04-08Bluetooth: hci_uart: add missing NULL check in h5_enqueuePavel Skripkin
[ Upstream commit 32cb08e958696908a9aad5e49a78d74f7e32fffb ] Syzbot hit general protection fault in __pm_runtime_resume(). The problem was in missing NULL check. hu->serdev can be NULL and we should not blindly pass &serdev->dev somewhere, since it will cause GPF. Reported-by: syzbot+b9bd12fbed3485a3e51f@syzkaller.appspotmail.com Fixes: d9dd833cf6d2 ("Bluetooth: hci_h5: Add runtime suspend") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-04-08Bluetooth: hci_serdev: call init_rwsem() before p->open()Pavel Skripkin
[ Upstream commit 9d7cbe2b9cf5f650067df4f402fdd799d4bbb4e1 ] kvartet reported, that hci_uart_tx_wakeup() uses uninitialized rwsem. The problem was in wrong place for percpu_init_rwsem() call. hci_uart_proto::open() may register a timer whose callback may call hci_uart_tx_wakeup(). There is a chance, that hci_uart_register_device() thread won't be fast enough to call percpu_init_rwsem(). Fix it my moving percpu_init_rwsem() call before p->open(). INFO: trying to register non-static key. The code is fine but needs lockdep annotation, or maybe you didn't initialize this object before use? turning off the locking correctness validator. CPU: 2 PID: 18524 Comm: syz-executor.5 Not tainted 5.16.0-rc6 #9 ... Call Trace: <IRQ> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 assign_lock_key kernel/locking/lockdep.c:951 [inline] register_lock_class+0x148d/0x1950 kernel/locking/lockdep.c:1263 __lock_acquire+0x106/0x57e0 kernel/locking/lockdep.c:4906 lock_acquire kernel/locking/lockdep.c:5637 [inline] lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5602 percpu_down_read_trylock include/linux/percpu-rwsem.h:92 [inline] hci_uart_tx_wakeup+0x12e/0x490 drivers/bluetooth/hci_ldisc.c:124 h5_timed_event+0x32f/0x6a0 drivers/bluetooth/hci_h5.c:188 call_timer_fn+0x1a5/0x6b0 kernel/time/timer.c:1421 Fixes: d73e17281665 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops") Reported-by: Yiru Xu <xyru1999@gmail.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-04-08Bluetooth: btintel: Fix WBS setting for Intel legacy ROM productsTedd Ho-Jeong An
[ Upstream commit 55235304c2560d4a94ccfff2a47ea927b4114064 ] This patch adds the flag to identify the Intel legacy ROM products that don't support WBS like WP and StP. Fixes: 3df4dfbec0f29 ("Bluetooth: btintel: Move hci quirks to setup routine") Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-03-28Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AELarry Finger
commit 2e7b4a328ed6ea57d22853939e69bc86c560996d upstream. This Realtek device has both wifi and BT components. The latter reports a USB ID of 0bda:2852, which is not in the table. BT device description in /sys/kernel/debug/usb/devices contains the following entries: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=2852 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms The missing USB_ID was reported by user trius65 at https://github.com/lwfinger/rtw89/issues/122 Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable@vger.kernel.org Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-28Bluetooth: btusb: Add another Realtek 8761BUHelmut Grohne
commit 6dfbe29f45fb0bde29213dbd754a79e8bfc6ecef upstream. This device is sometimes wrapped with a label "EDUP". T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=03 Dev#=107 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2550 ProdID=8761 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Helmut Grohne <helmut@subdivi.de> Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1955351 Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-27Bluetooth: btusb: Return error code when getting patch status failedMark Chen
commit 995d948cf2e45834275f07afc1c9881a9902e73c upstream. If there are failure cases in getting patch status, it should return the error code (-EIO). Fixes: fc342c4dc4087 ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-27Bluetooth: vhci: Set HCI_QUIRK_VALID_LE_STATESLuiz Augusto von Dentz
[ Upstream commit cfb4c313be670fd4bd09650216620fa4514cdb93 ] This set HCI_QUIRK_VALID_LE_STATES quirk which is required for the likes of experimental LE simultaneous roles. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: btintel: Add missing quirks and msft ext for legacy bootloaderTedd Ho-Jeong An
[ Upstream commit 3547a008c8962df2175db1e78b80f27e027ec549 ] This patch add missing HCI quirks and MSFT extension for legacy bootloader when it is running in the operational firmware. Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probeMiaoqian Lin
[ Upstream commit 6845667146a28c09b5dfc401c1ad112374087944 ] The function devm_gpiod_get_index() return error pointers on error. Thus devm_gpiod_get_index_optional() could return NULL and error pointers. The same as devm_gpiod_get_optional() function. Using IS_ERR_OR_NULL() check to catch error pointers. Fixes: 77131dfe ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: hci_bcm: Check for error irqJiasheng Jiang
[ Upstream commit b38cd3b42fba66cc538edb9cf77e07881f43f8e2 ] For the possible failure of the platform_get_irq(), the returned irq could be error number and will finally cause the failure of the request_irq(). Consider that platform_get_irq() can now in certain cases return -EPROBE_DEFER, and the consequences of letting request_irq() effectively convert that into -EINVAL, even at probe time rather than later on. So it might be better to check just now. Fixes: 0395ffc1ee05 ("Bluetooth: hci_bcm: Add PM for BCM devices") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: hci_qca: Stop IBS timer during BT OFFPanicker Harish
[ Upstream commit df1e5c51492fd93ffc293acdcc6f00698d19fedc ] The IBS timers are not stopped properly once BT OFF is triggered. we could see IBS commands being sent along with version command, so stopped IBS timers while Bluetooth is off. Fixes: 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990") Signed-off-by: Panicker Harish <quic_pharish@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: btusb: Handle download_firmware failure casesMark Chen
[ Upstream commit 00c0ee9850b7b0cb7c40b8daba806ae2245e59d4 ] For Mediatek chipset, it can not enabled if there are something wrong in btmtk_setup_firmware_79xx(). Thus, the process must be terminated and returned error code. Fixes: fc342c4dc4087 ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: btmtksdio: fix resume failureSean Wang
[ Upstream commit 561ae1d46a8ddcbc13162d5771f5ed6c8249e730 ] btmtksdio have to rely on MMC_PM_KEEP_POWER in pm_flags to avoid that SDIO power is being shut off during the device is in suspend. That fixes the SDIO command fails to access the bus after the device is resumed. Fixes: 7f3c563c575e7 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth") Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: virtio_bt: fix memory leak in virtbt_rx_handle()Soenke Huster
[ Upstream commit 1d0688421449718c6c5f46e458a378c9b530ba18 ] On the reception of packets with an invalid packet type, the memory of the allocated socket buffers is never freed. Add a default case that frees these to avoid a memory leak. Fixes: afd2daa26c7a ("Bluetooth: Add support for virtio transport driver") Signed-off-by: Soenke Huster <soenke.huster@eknoes.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: hci_vhci: Fix to set the force_wakeup valueTedd Ho-Jeong An
[ Upstream commit 8b89637dbac2d73d9f3dadf91b4a7dcdb1fc23af ] This patch sets the wakeup state of the vhci driver when the force_wakeup is updated. Fixes: 60edfad4fd0b6 ("Bluetooth: hci_vhci: Add force_prevent_wake entry") Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-16Bluetooth: btbcm: disable read tx power for MacBook Air 8,1 and 8,2Aditya Garg
commit 3318ae23bbcb14b7f68e9006756ba6d970955635 upstream. The MacBook Air 8,1 and 8,2 also need querying of LE Tx power to be disabled for Bluetooth to work. Signed-off-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btbcm: disable read tx power for some Macs with the T2 Security chipAditya Garg
commit 801b4c027b44a185292007d3cf7513999d644723 upstream. Some Macs with the T2 security chip had Bluetooth not working. To fix it we add DMI based quirks to disable querying of LE Tx power. Signed-off-by: Aditya Garg <gargaditya08@live.com> Reported-by: Orlando Chamberlain <redecorating@protonmail.com> Tested-by: Orlando Chamberlain <redecorating@protonmail.com> Link: https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com Fixes: 7c395ea521e6 ("Bluetooth: Query LE tx power on startup") Cc: stable@vger.kernel.org Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: bfusb: fix division by zero in send pathJohan Hovold
commit b5e6fa7a12572c82f1e7f2f51fbb02a322291291 upstream. Add the missing bulk-out endpoint sanity check to probe() to avoid division by zero in bfusb_send_frame() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing). Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")). Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add support for Foxconn QCA 0xe0d0Aaron Ma
commit 1cd563ebd0dc062127a85e84f934f4c697bb43ef upstream. Add an ID of Qualcomm Bluetooth SoC WCN6855. T: Bus=05 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d0 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I:* If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btintel: Fix broken LED quirk for legacy ROM devicesTedd Ho-Jeong An
commit 95655456e7cee858a23793f67025765b4c4c227b upstream. This patch fixes the broken LED quirk for Intel legacy ROM devices. To fix the LED issue that doesn't turn off immediately, the host sends the SW RFKILL command while shutting down the interface and it puts the devices in SW RFKILL state. Once the device is in SW RFKILL state, it can only accept HCI_Reset to exit from the SW RFKILL state. This patch checks the quirk for broken LED and sends the HCI_Reset before sending the HCI_Intel_Read_Version command. The affected legacy ROM devices are - 8087:07dc - 8087:0a2a - 8087:0aa7 Fixes: ffcba827c0a1d ("Bluetooth: btintel: Fix the LED is not turning off immediately") Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add support for Foxconn MT7922AAaron Ma
commit 6932627425d6d3849aecd43c02158a5312895ad4 upstream. Add 2 USB IDs for MT7922A chip. These 2 devices got the same description. T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d8 Rev= 1.00 T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d9 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add two more Bluetooth parts for WCN6855Zijun Hu
commit d2666be51d5f09662929888dd84d1f4d38c97127 upstream. Add USB IDs (0x10ab, 0x9309) and (0x10ab, 0x9409) to usb_device_id table for WCN6855. * /sys/kernel/debug/usb/devices T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9309 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9409 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add one more Bluetooth part for WCN6855Zijun Hu
commit e8c42585dc6032624a9728d8cf99d974e931d4bc upstream. Add a USB ID 0489:e0e3 of HP to usb_device_id table for WCN6855. -Device(0489:e0e3) from /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e3 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add the new support IDs for WCN6855tjiang@codeaurora.org
commit 21a241b3bc153b346987a28cc132674646589e02 upstream. Add the more IDs of HP to usb_device_id table for WCN6855. -Device(0489:e0cc) from /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0cc Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms -Device(0489:e0d6) from /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d6 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Tim Jiang <tjiang@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: enable Mediatek to support AOSP extensionmark-yw.chen
commit 28491d7ef4af471841e454f8c1f77384f93c6fef upstream. This patch enables AOSP extension for Mediatek Chip (MT7921 & MT7922). Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: fix memory leak in btusb_mtk_submit_wmt_recv_urb()Mark-YW.Chen
commit 60c6a63a3d3080a62f3e0e20084f58dbeff16748 upstream. Driver should free `usb->setup_packet` to avoid the leak. $ cat /sys/kernel/debug/kmemleak unreferenced object 0xffffffa564a58080 (size 128): backtrace: [<000000007eb8dd70>] kmem_cache_alloc_trace+0x22c/0x384 [<000000008a44191d>] btusb_mtk_hci_wmt_sync+0x1ec/0x994 [btusb] [<00000000ca7189a3>] btusb_mtk_setup+0x6b8/0x13cc [btusb] [<00000000c6105069>] hci_dev_do_open+0x290/0x974 [bluetooth] [<00000000a583f8b8>] hci_power_on+0xdc/0x3cc [bluetooth] [<000000005d80e687>] process_one_work+0x514/0xc80 [<00000000f4d57637>] worker_thread+0x818/0xd0c [<00000000dc7bdb55>] kthread+0x2f8/0x3b8 [<00000000f9999513>] ret_from_fork+0x10/0x30 Fixes: a1c49c434e150 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Signed-off-by: Mark-YW.Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Fix application of sizeof to pointerDavid Yang
commit dc1650fc94a8566fb89f3fd14a26d1cec7865f16 upstream. The coccinelle check report: "./drivers/bluetooth/btusb.c:2239:36-42: ERROR: application of sizeof to pointer". Using the real size to fix it. Fixes: 5a87679ffd443 ("Bluetooth: btusb: Support public address configuration for MediaTek Chip.") Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: David Yang <davidcomponentone@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AELarry Finger
commit 27fe097bc60a344ccd8107522184c2750f45df5c upstream. The Realtek RTL8852AE has both wifi and BT components. The latter reports a USB ID of 0bda:385a, which is not in the table. The portion of /sys/kernel/debug/usb/devices pertaining to this device is T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=385a Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-04Merge tag 'tty-5.16-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty / serial driver updates from Greg KH: "Here is the big set of tty and serial driver updates for 5.16-rc1. Nothing major in here at all, just lots of tiny serial and tty driver updates for various reported things, and some good cleanups. These include: - more good tty api cleanups from Jiri - stm32 serial driver updates - softlockup fix for non-preempt systems under high serial load - rpmsg serial driver update - 8250 drivers updates and fixes - n_gsm line discipline fixes and updates as people are finally starting to use it. All of these have been in linux-next for a while now with no reported issues" * tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits) tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE tty: rpmsg: Define tty name via constant string literal tty: rpmsg: Add pr_fmt() to prefix messages tty: rpmsg: Use dev_err_probe() in ->probe() tty: rpmsg: Unify variable used to keep an error code tty: rpmsg: Assign returned id to a local variable serial: stm32: push DMA RX data before suspending serial: stm32: terminate / restart DMA transfer at suspend / resume serial: stm32: rework RX dma initialization and release serial: 8250_pci: Remove empty stub pci_quatech_exit() serial: 8250_pci: Replace custom pci_match_id() implementation serial: xilinx_uartps: Fix race condition causing stuck TX serial: sunzilog: Mark sunzilog_putchar() __maybe_unused Revert "tty: hvc: pass DMA capable memory to put_chars()" Revert "virtio-console: remove unnecessary kmemdup()" serial: 8250_pci: Replace dev_*() by pci_*() macros serial: 8250_pci: Get rid of redundant 'else' keyword serial: 8250_pci: Refactor the loop in pci_ite887x_init() tty: add rpmsg driver ...
2021-10-01Bluetooth: Rename driver .prevent_wake to .wakeupLuiz Augusto von Dentz
prevent_wake logic is backward since what it is really checking is if the device may wakeup the system or not, not that it will prevent the to be awaken. Also looking on how other subsystems have the entry as power/wakeup this also renames the force_prevent_wake to force_wakeup in vhci driver. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-01Bluetooth: btrtl: Ask ic_info to drop firmwareHilda Wu
Some un-support wakeup platforms keep USB power and suspend signal is coming late, this makes Realtek some chip keep its firmware, and make it never load new firmware. So use vendor specific HCI command to ask them drop its firmware after system shutdown or resume. Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-01Bluetooth: btusb: Add support for TP-Link UB500 AdapterNicholas Flintham
Add support for TP-Link UB500 Adapter (RTL8761B) * /sys/kernel/debug/usb/devices T: Bus=01 Lev=02 Prnt=05 Port=01 Cnt=01 Dev#= 78 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2357 ProdID=0604 Rev= 2.00 S: Manufacturer= S: Product=TP-Link UB500 Adapter S: SerialNumber=E848B8C82000 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Nicholas Flintham <nick@flinny.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-30Bluetooth: btrtl: Add support for MSFT extension to rtl8821c devicesMarcel Holtmann
The rtl8821c class of Realtek devices does support the Microsoft extensions and thus enable them. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2021-09-29Bluetooth: hci_vhci: Add force_prevent_wake entryLuiz Augusto von Dentz
This adds force_prevent_wake which can be used to force a certain state while interacting with force_suspend. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-29Bluetooth: hci_vhci: Add force_suspend entryLuiz Augusto von Dentz
This adds force_suspend which can be used to force the controller into suspend/resume state. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-29Bluetooth: btrsi: remove superfluous header files from btrsi.cMianhan Liu
btrsi.c hasn't use any macro or function declared in net/genetlink.h. Thus, these files can be removed from btrsi.c safely without affecting the compilation of the ./drivers/bluetooth module Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-28Bluetooth: btrtl: Set VsMsftOpCode based on device tableMarcel Holtmann
The device table already has the option to hold device specific details and thus include the support for Microsoft extensions there as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2021-09-28Bbluetooth: btusb: Add another Bluetooth part for Realtek 8852AELarry Finger
This Realtek device has both wifi and BT components. The latter reports a USB ID of 0bda:4852, which is not in the table. When adding the new device, I noticed that the RTL8852AE was mentioned in two places. These are now combined. The portion of /sys/kernel/debug/usb/devices pertaining to this device is T: Bus=06 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=4852 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Cc: Stable <stable@vger.kernel.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-28Bluetooth: btrtl: enable Realtek 8822C/8852A to support AOSP extensionJoseph Hwang
This patch enables Realtek 8822C and 8852A to support the AOSP extension. Reviewed-by: Miao-chen Chou <mcchou@chromium.org> Signed-off-by: Joseph Hwang <josephsih@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-28Bluetooth: hci_qca: enable Qualcomm WCN399x for AOSP extensionJoseph Hwang
This patch enables Qualcomm WCN399x to support the AOSP extension. Reviewed-by: Miao-chen Chou <mcchou@chromium.org> Signed-off-by: Joseph Hwang <josephsih@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-24Bluetooth: hci_h5: directly return hci_uart_register_device() ret-valHans de Goede
Since the hci_uart_register_device() call is the last thing we do in h5_serdev_probe() we can simply directly return its return-value. Cc: Archie Pusaka <apusaka@google.com> Suggested-by: Archie Pusaka <apusaka@google.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-24Bluetooth: hci_h5: Fix (runtime)suspend issues on RTL8723BS HCIsHans de Goede
The recently added H5_WAKEUP_DISABLE h5->flags flag gets checked in h5_btrtl_open(), but it gets set in h5_serdev_probe() *after* calling hci_uart_register_device() and thus after h5_btrtl_open() is called, set this flag earlier. Also on devices where suspend/resume involves fully re-probing the HCI, runtime-pm suspend should not be used, make the runtime-pm setup conditional on the H5_WAKEUP_DISABLE flag too. This fixes the HCI being removed and then re-added every 10 seconds because it was being reprobed as soon as it was runtime-suspended. Fixes: 66f077dde749 ("Bluetooth: hci_h5: add WAKEUP_DISABLE flag") Fixes: d9dd833cf6d2 ("Bluetooth: hci_h5: Add runtime suspend") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Archie Pusaka <apusaka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-22tty: remove file from n_tty_ioctl_helperJiri Slaby
After the previous patch, there are no users of 'file' in n_tty_ioctl_helper. So remove it also from there. Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: Paul Mackerras <paulus@samba.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210914091134.17426-6-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-22Bluetooth: btmtkuart: fix a memleak in mtk_hci_wmt_syncDinghao Liu
bdev->evt_skb will get freed in the normal path and one error path of mtk_hci_wmt_sync, while the other error paths do not free it, which may cause a memleak. This bug is suggested by a static analysis tool, please advise. Fixes: e0b67035a90b ("Bluetooth: mediatek: update the common setup between MT7622 and other devices") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-22Bluetooth: hci_ldisc: require CAP_NET_ADMIN to attach N_HCI ldiscThadeu Lima de Souza Cascardo
Any unprivileged user can attach N_HCI ldisc and send packets coming from a virtual controller by using PTYs. Require initial namespace CAP_NET_ADMIN to do that. Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-21Bluetooth: btusb: Add gpio reset way for qca btsoc in cmd_timeouttjiang@codeaurora.org
if platform provide gpio connect to BT_EN reset pin of qca btsoc chip, we can do hardware reset instead of usb port reset. Signed-off-by: Tim Jiang <tjiang@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-10Bluetooth: hci_uart: fix GPF in h5_recvPavel Skripkin
Syzbot hit general protection fault in h5_recv(). The problem was in missing NULL check. hu->serdev can be NULL and we cannot blindly pass &serdev->dev somewhere, since it can cause GPF. Fixes: d9dd833cf6d2 ("Bluetooth: hci_h5: Add runtime suspend") Reported-and-tested-by: syzbot+7d41312fe3f123a6f605@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-10Bluetooth: btintel: Fix incorrect out of memory checkColin Ian King
Currently *ven_data is being assigned the return from a kmalloc call but the out-of-memory check is checking ven_data and not *ven_data. Fix this by adding the missing dereference * operator, Addresses-Coverity: ("Dereference null return") Fixes: 70dd978952bc ("Bluetooth: btintel: Define a callback to fetch codec config data") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-09-07Bluetooth: hci_vhci: Add support for offload codecs over SCOKiran K
Define the callbacks required to support offload codecs Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit v1.2.3 (git 2.51.0) at 2026-10-16 14:59:10 +0000