| Age | Commit message (Collapse) | Author |
|---|
|
Enable CRU, I2C0 and CSI on RZ/G3E SMARC EVK and tie the CSI to the
OV5645 sensor using Device Tree overlay. RZ/G3E SMARK EVK is a RZ/G2L
alike EVK hence reuse rz-smarc-cru-csi-ov5645.dtsi.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514162422.910114-5-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable device I2C0 node for the RZ SMARC Carrier-II Board and set clock
frequency to 400kHz.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514162422.910114-4-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add device node for I2C0 pincontrol.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514162422.910114-3-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add CRU, CSI2 nodes to RZ/RZG3E SoC DTSI.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514162422.910114-2-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable the Mali-G31 GPU on the RZ/V2N EVK.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the device tree node for the ARM Mali-G31 GPU found on selected
variants of the Renesas RZ/V2N (R9A09G056) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable WDT1 hardware block on the RZ/V2N EVK.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-9-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add WDT0-WDT3 nodes to RZ/V2N ("R9A09G056") SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable the RIIC controllers 0, 1, 2, 3, 6, 7, and 8 which are populated
on the RZ/V2N EVK.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the nine RIIC controllers present on the Renesas RZ/V2N (R9A09G056)
SoC to its DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable OSTM0-OSTM7 instances in the RZ/V2N EVK device tree so that all
eight OSTM general timers are active and available.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add OSTM0-OSTM7 nodes to RZ/V2N ("R9A09G056") SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable GBETH nodes on RZ/V2N EVK.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Renesas RZ/V2N SoC is equipped with 2x Synopsys DesignWare Ethernet
Quality-of-Service IP block version 5.20. Add GBETH nodes to R9A09G056
RZ/V2N SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514101528.41663-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable the GBETH nodes on the RZ/V2H Evaluation Kit.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250513131412.253091-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Renesas RZ/V2H(P) SoC is equipped with 2x Synopsys DesignWare Ethernet
Quality-of-Service IP block version 5.20. Add GBETH nodes to R9A09G057
RZ/V2H(P) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250513131412.253091-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable Renesas AT25QL128A FLASH connected to XSPI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250508183109.137721-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add XSPI node to RZ/G3E ("R9A09G047") SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250508183109.137721-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This changes the semantics of BPF_NOSPEC (previously a v4-only barrier)
to always emit a speculation barrier that works against both Spectre v1
AND v4. If mitigation is not needed on an architecture, the backend
should set bpf_jit_bypass_spec_v4/v1().
As of now, this commit only has the user-visible implication that unpriv
BPF's performance on PowerPC is reduced. This is the case because we
have to emit additional v1 barrier instructions for BPF_NOSPEC now.
This commit is required for a future commit to allow us to rely on
BPF_NOSPEC for Spectre v1 mitigation. As of this commit, the feature
that nospec acts as a v1 barrier is unused.
Commit f5e81d111750 ("bpf: Introduce BPF nospec instruction for
mitigating Spectre v4") noted that mitigation instructions for v1 and v4
might be different on some archs. While this would potentially offer
improved performance on PowerPC, it was dismissed after the following
considerations:
* Only having one barrier simplifies the verifier and allows us to
easily rely on v4-induced barriers for reducing the complexity of
v1-induced speculative path verification.
* For the architectures that implemented BPF_NOSPEC, only PowerPC has
distinct instructions for v1 and v4. Even there, some insns may be
shared between the barriers for v1 and v4 (e.g., 'ori 31,31,0' and
'sync'). If this is still found to impact performance in an
unacceptable way, BPF_NOSPEC can be split into BPF_NOSPEC_V1 and
BPF_NOSPEC_V4 later. As an optimization, we can already skip v1/v4
insns from being emitted for PowerPC with this setup if
bypass_spec_v1/v4 is set.
Vulnerability-status for BPF_NOSPEC-based Spectre mitigations (v4 as of
this commit, v1 in the future) is therefore:
* x86 (32-bit and 64-bit), ARM64, and PowerPC (64-bit): Mitigated - This
patch implements BPF_NOSPEC for these architectures. The previous
v4-only version was supported since commit f5e81d111750 ("bpf:
Introduce BPF nospec instruction for mitigating Spectre v4") and
commit b7540d625094 ("powerpc/bpf: Emit stf barrier instruction
sequences for BPF_NOSPEC").
* LoongArch: Not Vulnerable - Commit a6f6a95f2580 ("LoongArch, bpf: Fix
jit to skip speculation barrier opcode") is the only other past commit
related to BPF_NOSPEC and indicates that the insn is not required
there.
* MIPS: Vulnerable (if unprivileged BPF is enabled) -
Commit a6f6a95f2580 ("LoongArch, bpf: Fix jit to skip speculation
barrier opcode") indicates that it is not vulnerable, but this
contradicts the kernel and Debian documentation. Therefore, I assume
that there exist vulnerable MIPS CPUs (but maybe not from Loongson?).
In the future, BPF_NOSPEC could be implemented for MIPS based on the
GCC speculation_barrier [1]. For now, we rely on unprivileged BPF
being disabled by default.
* Other: Unknown - To the best of my knowledge there is no definitive
information available that indicates that any other arch is
vulnerable. They are therefore left untouched (BPF_NOSPEC is not
implemented, but bypass_spec_v1/v4 is also not set).
I did the following testing to ensure the insn encoding is correct:
* ARM64:
* 'dsb nsh; isb' was successfully tested with the BPF CI in [2]
* 'sb' locally using QEMU v7.2.15 -cpu max (emitted sb insn is
executed for example with './test_progs -t verifier_array_access')
* PowerPC: The following configs were tested locally with ppc64le QEMU
v8.2 '-machine pseries -cpu POWER9':
* STF_BARRIER_EIEIO + CONFIG_PPC_BOOK32_64
* STF_BARRIER_SYNC_ORI (forced on) + CONFIG_PPC_BOOK32_64
* STF_BARRIER_FALLBACK (forced on) + CONFIG_PPC_BOOK32_64
* CONFIG_PPC_E500 (forced on) + STF_BARRIER_EIEIO
* CONFIG_PPC_E500 (forced on) + STF_BARRIER_SYNC_ORI (forced on)
* CONFIG_PPC_E500 (forced on) + STF_BARRIER_FALLBACK (forced on)
* CONFIG_PPC_E500 (forced on) + STF_BARRIER_NONE (forced on)
Most of those cobinations should not occur in practice, but I was not
able to get an PPC e6500 rootfs (for testing PPC_E500 without forcing
it on). In any case, this should ensure that there are no unexpected
conflicts between the insns when combined like this. Individual v1/v4
barriers were already emitted elsewhere.
Hari's ack is for the PowerPC changes only.
[1] https://gcc.gnu.org/git/?p=gcc.git;a=commit;h=29b74545531f6afbee9fc38c267524326dbfbedf
("MIPS: Add speculation_barrier support")
[2] https://github.com/kernel-patches/bpf/pull/8576
Signed-off-by: Luis Gerhorst <luis.gerhorst@fau.de>
Acked-by: Hari Bathini <hbathini@linux.ibm.com>
Cc: Henriette Herzog <henriette.herzog@rub.de>
Cc: Maximilian Ott <ott@cs.fau.de>
Cc: Milan Stephan <milan.stephan@fau.de>
Link: https://lore.kernel.org/r/20250603211703.337860-1-luis.gerhorst@fau.de
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
JITs can set bpf_jit_bypass_spec_v1/v4() if they want the verifier to
skip analysis/patching for the respective vulnerability. For v4, this
will reduce the number of barriers the verifier inserts. For v1, it
allows more programs to be accepted.
The primary motivation for this is to not regress unpriv BPF's
performance on ARM64 in a future commit where BPF_NOSPEC is also used
against Spectre v1.
This has the user-visible change that v1-induced rejections on
non-vulnerable PowerPC CPUs are avoided.
For now, this does not change the semantics of BPF_NOSPEC. It is still a
v4-only barrier and must not be implemented if bypass_spec_v4 is always
true for the arch. Changing it to a v1 AND v4-barrier is done in a
future commit.
As an alternative to bypass_spec_v1/v4, one could introduce NOSPEC_V1
AND NOSPEC_V4 instructions and allow backends to skip their lowering as
suggested by commit f5e81d111750 ("bpf: Introduce BPF nospec instruction
for mitigating Spectre v4"). Adding bpf_jit_bypass_spec_v1/v4() was
found to be preferable for the following reason:
* bypass_spec_v1/v4 benefits non-vulnerable CPUs: Always performing the
same analysis (not taking into account whether the current CPU is
vulnerable), needlessly restricts users of CPUs that are not
vulnerable. The only use case for this would be portability-testing,
but this can later be added easily when needed by allowing users to
force bypass_spec_v1/v4 to false.
* Portability is still acceptable: Directly disabling the analysis
instead of skipping the lowering of BPF_NOSPEC(_V1/V4) might allow
programs on non-vulnerable CPUs to be accepted while the program will
be rejected on vulnerable CPUs. With the fallback to speculation
barriers for Spectre v1 implemented in a future commit, this will only
affect programs that do variable stack-accesses or are very complex.
For PowerPC, the SEC_FTR checking in bpf_jit_bypass_spec_v4() is based
on the check that was previously located in the BPF_NOSPEC case.
For LoongArch, it would likely be safe to set both
bpf_jit_bypass_spec_v1() and _v4() according to
commit a6f6a95f2580 ("LoongArch, bpf: Fix jit to skip speculation
barrier opcode"). This is omitted here as I am unable to do any testing
for LoongArch.
Hari's ack concerns the PowerPC part only.
Signed-off-by: Luis Gerhorst <luis.gerhorst@fau.de>
Acked-by: Hari Bathini <hbathini@linux.ibm.com>
Cc: Henriette Herzog <henriette.herzog@rub.de>
Cc: Maximilian Ott <ott@cs.fau.de>
Cc: Milan Stephan <milan.stephan@fau.de>
Link: https://lore.kernel.org/r/20250603211318.337474-1-luis.gerhorst@fau.de
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Enable SLPI, Sensors DSP on the Lenovo Yoga C630. The DSP boots the
firmware and provides QMI services, however it is of limited
functionality due to the missing fastrpc_shell_1 binary.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250608-c630-slpi-v1-1-72210249e37e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The user space calls mmap() to map VAS window paste address
and the kernel returns the complete mapped page for each
window. So return -EINVAL if non-zero is passed for offset
parameter to mmap().
See Documentation/arch/powerpc/vas-api.rst for mmap()
restrictions.
Co-developed-by: Jonathan Greental <yonatan02greental@gmail.com>
Signed-off-by: Jonathan Greental <yonatan02greental@gmail.com>
Reported-by: Jonathan Greental <yonatan02greental@gmail.com>
Fixes: dda44eb29c23 ("powerpc/vas: Add VAS user space API")
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250610021227.361980-2-maddy@linux.ibm.com
|
|
The fingerprint sensor, hidden in the power button, is connected to one
of the USB multiport ports; while the other port is unused.
Describe the USB controller, the four phys and the repeater involved to
make the fingerprint sensor operational.
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250605-xps13-fingerprint-v2-1-eebf84c172f2@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The Qualcomm CPUCP mailbox driver needs to be enabled for CPU frequency
scaling to work on the X Elite platform, so enable this driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250605-enable-cpucp-v1-1-111ecef7e4c9@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
memtrace mmap issue has an out of bounds issue. This patch fixes the by
checking that the requested mapping region size should stay within the
allocated region size.
Reported-by: Jonathan Greental <yonatan02greental@gmail.com>
Fixes: 08a022ad3dfa ("powerpc/powernv/memtrace: Allow mmaping trace buffers")
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250610021227.361980-1-maddy@linux.ibm.com
|
|
bcm-nsp.dtsi has #pwm-cells = <3> as is specified in the binding. So to
also use that correct value for bcm958625-meraki-mx6x the property
overriding that value just has to be dropped. This fixes a few warnings
like:
arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65.dtb: pwm@31000: #pwm-cells: 3 was expected
from schema $id: http://devicetree.org/schemas/pwm/brcm,iproc-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250527181320.373572-2-u.kleine-koenig@baylibre.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.
Add the watchdog, GPIO, RNG, LED and DMA blocks for the
BCM63178 based on the vendor files 63178_map_part.h and
63178_intr.h from the "bcmopen-consumer" code drop.
This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-8-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.
Add the GPIO, RNG and LED and DMA blocks for the
BCM63148 based on the vendor files 63148_map_part.h and
63148_intr.h from the "bcmopen-consumer" code drop.
This SoC has up to 160 possible GPIOs due to having 5
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-7-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.
Extend the peripheral interrupt window to 0x10000 as it need
to fit the DMA block.
Add the GPIO, RNG and LED and DMA blocks for the
BCM63138 based on the vendor files 63138_map_part.h and
63138_intr.h from the "bcmopen-consumer" code drop.
This SoC has up to 160 possible GPIOs due to having 5
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-6-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.
Add the first and second watchdog, GPIO, RNG, LED and
DMA blocks for the BCM6878 based on the vendor files
6878_map_part.h and 6878_intr.h from the "bcmopen-consumer"
code drop.
This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-5-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.
Add the first and second watchdog, GPIO, RNG, LED, DMA and
second PL011 UART blocks for the BCM6855 based on the vendor
files 6855_map_part.h and 6855_intr.h from the
"bcmopen-consumer" code drop.
This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-4-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
The r200 RNG has an interrupt so let's add it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-3-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
According to the vendor file 6878_intr.h the UART0 has IRQ
92, not 32.
Assuming this is a copy-and-paste error.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-1-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
Define the RP1 node in an overlay. The inclusion tree is
as follow (the arrow points to the includer):
rp1.dtso
^
|
rp1-common.dtsi ----> rp1-nexus.dtsi
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250529135052.28398-10-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
Add the fully populated DTS for RaspberryPi 5 which includes
the RP1 node definition. The inclusion tree is as follow (the
arrow points to the includer):
rp1-common.dtsi ----> rp1-nexus.dtsi ----> bcm2712-rpi-5-b.dts
^
|
bcm2712-rpi-5-b-ovl-rp1.dts
This is designed to maximize the compatibility with downstream DT
while ensuring that a fully defined DT (one which includes the RP1
node as opposed to load it from overlay at runtime) is present
since early boot stage.
Since the preferred board DT is the fully populated one, name it
bcm2712-rpi-5-b.dts and move the previous one into
bcm2712-rpi-5-b-ovl-rp1.dts.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20250529135052.28398-9-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
The RP1 found on Raspberry Pi 5 board needs an external crystal at 50MHz.
Add clk_rp1_xosc node to provide that.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250529135052.28398-8-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
RaspberryPi RP1 is a multi function PCI endpoint device that
exposes several subperipherals via PCI BAR.
Add a dtb overlay that will be compiled into a binary blob
and linked in the RP1 driver.
This overlay offers just minimal support to represent the
RP1 device itself, the sub-peripherals will be added by
future patches.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250529135052.28398-6-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.
Add the watchdog, GPIO blocks, RNG, LED, second UART and DMA
blocks for the BCM63158 based on the vendor files 63158_map_part.h
and 63158_intr.h from the "bcmopen-consumer" code drop.
The DTSI file has clearly been authored for the B0 revision of
the SoC: there is an earlier A0 version, but this has
the UARTs in the legacy PERF memory space, while the B0
has opened a new peripheral window at 0xff812000 for the
three UARTs. It also has a designated AHB peripheral area
at 0xff810000 where the DMA resides, the peripheral range
window fits these two peripheral groups.
This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-12-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. ARM64 SoCs have additional
peripherals at 0xff858000. Extend the peripheral window range
to 0x400000 and add the DMA controller at offset 0x59000.
Add the watchdog, GPIO blocks, RNG, LED, second UART and DMA
blocks for the BCM6858 based on the vendor files 6858_map_part.h
and 6858_intr.h from the "bcmopen-consumer" code drop.
This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-11-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. ARM64 SoCs have additional
peripherals at 0xff858000. Extend the BCM6856 the PERF window
to 0x400000 and add the DMA block at offset 0x59000.
Add the watchdog, GPIO blocks, RNG, LED, second UART and DMA
blocks for the BCM6856 based on the vendor files 6856_map_part.h
and 6856_intr.h from the "bcmopen-consumer" code drop.
This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-10-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. ARM64 SoCs have additional
peripherals at 0xff858000, we extend the peripheral bus
range to 0x400000 to cover this area.
Add the watchdog, remaining GPIO blocks, RNG, and DMA blocks
for the BCM4908 based on the vendor files 4908_map_part.h
and 4908_intr.h from the "bcmopen-consumer" code drop.
This SoC has up to 320 possible GPIOs due to having 10
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20250512-bcmbca-peripherals-arm-v3-9-86f97ab4326f@linaro.org
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
The RP1 driver uses the infrastructure enabled by OF_OVERLAY config
option. Enable that option in defconfig in order to produce a kernel
usable on RaspberryPi5 avoiding to enable it separately.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250529135052.28398-12-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
Select the RP1 drivers needed to operate the PCI endpoint containing
several peripherals such as Ethernet and USB Controller. This chip is
present on RaspberryPi 5.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250529135052.28398-11-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
Enable eMMC support for SpacemiT K1 SoC, successfully tested on
Bananapi-F3 board which shipped with a 16GB eMMC chip - KLMAG1JETD-B041.
Link: https://lore.kernel.org/r/20250523-22-k1-sdhci-v1-1-6e0adddf7494@gentoo.org
Signed-off-by: Yixun Lan <dlan@gentoo.org>
|
|
While the GCC and Clang compilers already define __ASSEMBLER__
automatically when compiling assembly code, __ASSEMBLY__ is a
macro that only gets defined by the Makefiles in the kernel.
This can be very confusing when switching between userspace
and kernelspace coding, or when dealing with uapi headers that
rather should use __ASSEMBLER__ instead. So let's standardize on
the __ASSEMBLER__ macro that is provided by the compilers now.
This is a completely mechanical patch (done with a simple "sed -i"
statement).
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
|
|
__ASSEMBLY__ is only defined by the Makefile of the kernel, so
this is not really useful for uapi headers (unless the userspace
Makefile defines it, too). Let's switch to __ASSEMBLER__ which
gets set automatically by the compiler when compiling assembly
code.
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
|
|
The custom swap function used in sort() was identical to the default
built-in sort swap. Remove the custom swap function and passes NULL to
sort(), allowing it to use the default swap function.
This change reduces code size and improves performance, particularly when
CONFIG_MITIGATION_RETPOLINE is enabled. With RETPOLINE mitigation, indirect
function calls incur significant overhead, and using the default swap
function avoids this cost.
$ ./scripts/bloat-o-meter ./unwind.o.old ./unwind.o.new
add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-22 (-22)
Function old new delta
init_unwind_hdr.constprop 544 540 -4
swap_eh_frame_hdr_table_entries 18 - -18
Total: Before=4410, After=4388, chg -0.50%
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
|
|
The core atomic code has a number of macros where it elaborates
architecture primitives into more functions. ARC uses
arch_atomic64_cmpxchg() as it's architecture primitive which disable alot
of the additional functions.
Instead provide arch_cmpxchg64_relaxed() as the primitive and rely on the
core macros to create arch_cmpxchg64().
The macros will also provide other functions, for instance,
try_cmpxchg64_release(), giving a more complete implementation.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/Z0747n5bSep4_1VX@J2N7QTR9R3
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
|
|
SIGTRAP handler
Clear the software event flag in the augmented SS to prevent immediate
repeat of single step trap on return from SIGTRAP handler if the trap
flag (TF) is set without an external debugger attached.
Following is a typical single-stepping flow for a user process:
1) The user process is prepared for single-stepping by setting
RFLAGS.TF = 1.
2) When any instruction in user space completes, a #DB is triggered.
3) The kernel handles the #DB and returns to user space, invoking the
SIGTRAP handler with RFLAGS.TF = 0.
4) After the SIGTRAP handler finishes, the user process performs a
sigreturn syscall, restoring the original state, including
RFLAGS.TF = 1.
5) Goto step 2.
According to the FRED specification:
A) Bit 17 in the augmented SS is designated as the software event
flag, which is set to 1 for FRED event delivery of SYSCALL,
SYSENTER, or INT n.
B) If bit 17 of the augmented SS is 1 and ERETU would result in
RFLAGS.TF = 1, a single-step trap will be pending upon completion
of ERETU.
In step 4) above, the software event flag is set upon the sigreturn
syscall, and its corresponding ERETU would restore RFLAGS.TF = 1.
This combination causes a pending single-step trap upon completion of
ERETU. Therefore, another #DB is triggered before any user space
instruction is executed, which leads to an infinite loop in which the
SIGTRAP handler keeps being invoked on the same user space IP.
Fixes: 14619d912b65 ("x86/fred: FRED entry/exit and dispatch code")
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250609084054.2083189-2-xin%40zytor.com
|
|
The touch panel display is an optional add on for the RockPro64
so this should be an DT overlay, drop the panel options in
preparation to add this as an overlay.
This effectively reverts commit b65155c786c4 so as to add an
overlay for it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20250518215944.178582-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
