| Age | Commit message (Collapse) | Author |
|---|
|
When an ifdef is used in the below manner, second one could be considered
as duplicate.
ifdef DEFINE_A
...code block...
ifdef DEFINE_A <-- This is a duplicate.
...code block...
endif
else
ifndef DEFINE_A <-- This is also duplicate.
...code block...
endif
endif
More details about the script and methods used to find these code
patterns are in cover letter of [1].
Few places in arch/powerpc where this pattern was seen:
paca.h:
Hunk1: Code is under check of CONFIG_PPC64 from line 13, hence the
second CONFIG_PPC64 at line 166 is a duplicate.
Hunk2: CONFIG_PPC_BOOK3S_64 was defined back to back. Merged the two
ifdefs.
asm-offsets.c:
Code is under check of CONFIG_PPC64 from line 176 hence second
CONFIG_PPC64 at line 249 is a duplicate.
powermac/feature.c:
#ifndef CONFIG_PPC64 is used at line 2066. And then in #else again
#ifdef CONFIG_PPC64 is used. Which is a duplicate since in #else means
CONFIG_PPC64 is defined.
xmon.c:
Code is under the check of CONFIG_SMP from line 521 hence the same
check of CONFIG_SMP at line 646 is a duplicate.
No functional change is intended here. It only aims to improve code
readability.
[1] https://lore.kernel.org/all/20240118080326.13137-1-sshegde@linux.ibm.com/
Signed-off-by: Shrikanth Hegde <sshegde@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240216053016.528906-1-sshegde@linux.ibm.com
|
|
The PCI node interrupt-map properties have the wrong size as #address-cells
in the interrupt parent are not accounted for.
The dtc interrupt_map check catches this, but the warning is off because
its dependency, interrupt_provider, is off by default.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-5-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The dtc interrupt_map warning is off because its dependency,
interrupt_provider, is off by default. Fix all the warnings so it can be
enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-4-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Chanho Min <chanho.min@lge.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-3-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-2-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Several Freescale Layerscape platforms extirq binding use a malformed
interrupt-map property missing parent address cells. These are
documented in of_irq_imap_abusers list in drivers/of/irq.c. In order to
enable dtc interrupt_map check tree wide, we need to disable it for
these platforms which will not be fixed (as that would break
compatibility).
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-1-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/defconfig
Renesas ARM defconfig updates for v6.9
- Disable obsolete board staging support in the Renesas ARM and ARM V7
multi-platform defconfigs,
- Enable support for the Renesas R-Car V4M (R8A779H0) SoC in the ARM64
defconfig.
* tag 'renesas-arm-defconfig-for-v6.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: defconfig: Enable R8A779H0 SoC
ARM: multi_v7_defconfig: Disable board staging
ARM: shmobile: defconfig: Disable staging
Link: https://lore.kernel.org/r/cover.1707487828.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
A couple of new platforms got added since last year when Mark
added virt.config, so turn these off as well.
Link: https://lore.kernel.org/r/20240219093819.644324-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Some fixes to make devicetrees conform to bindings better (pwm irqs), dt
styling fixes (unneeded jaguar status, whitespaces, Cool Pi regulator
naming) and functionality fixes (px30 spi chipselect number, allowing
rk3588-evb1 to turn off, pcie lane numbers on CoolPi, wrong gpio-names
on Indidroid Nova and some CoolPi sdmmc aliases to match what uboot uses).
* tag 'v6.8-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Correct Indiedroid Nova GPIO Names
arm64: dts: rockchip: Drop interrupts property from rk3328 pwm-rockchip node
arm64: dts: rockchip: set num-cs property for spi on px30
arm64: dts: rockchip: minor rk3588 whitespace cleanup
arm64: dts: rockchip: drop unneeded status from rk3588-jaguar gpio-leds
ARM: dts: rockchip: Drop interrupts property from pwm-rockchip nodes
arm64: dts: rockchip: Fix the num-lanes of pcie3x4 on Cool Pi CM5 EVB
arm64: dts: rockchip: rename vcc5v0_usb30_host regulator for Cool Pi CM5 EVB
arm64: dts: rockchip: aliase sdmmc as mmc1 for Cool Pi CM5 EVB
arm64: dts: rockchip: aliase sdmmc as mmc1 for Cool Pi 4B
arm64: dts: rockchip: mark system power controller on rk3588-evb1
Link: https://lore.kernel.org/r/2450634.jE0xQCEvom@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There is already a generic union definition for vdso_data_store in the vdso
datapage header.
Use this definition to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20240219153939.75719-11-anna-maria@linutronix.de
|
|
There is already a generic union definition for vdso_data_store in the vdso
datapage header.
Use this definition to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240219153939.75719-10-anna-maria@linutronix.de
|
|
There is already a generic union definition for vdso_data_store in vdso
datapage header.
Use this definition to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240219153939.75719-9-anna-maria@linutronix.de
|
|
There is already a generic union definition for vdso_data_store in the vdso
datapage header.
Use this definition to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219153939.75719-8-anna-maria@linutronix.de
|
|
There is already a generic union definition for vdso_data_store in the vdso
datapage header.
Use this definition to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240220085212.6547-1-anna-maria@linutronix.de
|
|
There is already a generic union definition for vdso_data_store in vdso
datapage header.
Use this definition to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240219153939.75719-6-anna-maria@linutronix.de
|
|
The vDSO data page "union vdso_data_store" is defined in an ARM specific
header file and also defined in several other places.
Move the definition from the ARM header file into the generic vdso datapage
header to make it also usable for others and to prevent code duplication.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240219153939.75719-5-anna-maria@linutronix.de
|
|
CSKY selects GENERIC_TIME_VSYSCALL. GENERIC_TIME_VSYSCALL dependent
ifdeffery is superfluous. Clean it up.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20240219153939.75719-4-anna-maria@linutronix.de
|
|
vdso/datapage.h includes the architecture specific vdso/data.h header
file. So there is no need to do it also the other way round and including
the generic vdso/datapage.h header file inside the architecture specific
data.h header file.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219153939.75719-3-anna-maria@linutronix.de
|
|
On arm64, kprobes always take an exception and so create a struct
pt_regs through the usual exception entry logic. Similarly kretprobes
taskes and exception for function entry, but for function returns it
uses a trampoline which attempts to create a struct pt_regs without
taking an exception.
This is problematic for a few reasons, including:
1) The kretprobes trampoline neither saves nor restores all of the
portions of PSTATE. Before invoking the handler it saves a number of
portions of PSTATE, and after returning from the handler it restores
NZCV before returning to the original return address provided by the
handler.
2) The kretprobe trampoline constructs the PSTATE value piecemeal from
special purpose registers as it cannot read all of PSTATE atomically
without taking an exception. This is somewhat fragile, and it's not
possible to reliably recover PSTATE information which only exists on
some physical CPUs (e.g. when SSBS support is mismatched).
Today the kretprobes trampoline does not record:
- BTYPE
- SSBS
- ALLINT
- SS
- PAN
- UAO
- DIT
- TCO
... and this will only get worse with future architecture extensions
which add more PSTATE bits.
3) The kretprobes trampoline doesn't store portions of struct pt_regs
(e.g. the PMR value when using pseudo-NMIs). Due to this, helpers
which operate on a struct pt_regs, such as interrupts_enabled(), may
not work correctly.
4) The function entry and function exit handlers run in different
contexts. The entry handler will always be run in a debug exception
context (which is currently treated as an NMI), but the return will
be treated as whatever context the instrumented function was executed
in. The differences between these contexts are liable to cause
problems (e.g. as the two can be differently interruptible or
preemptible, adversely affecting synchronization between the
handlers).
5) As the kretprobes trampoline runs in the same context as the code
being probed, it is subject to the same single-stepping context,
which may not be desirable if this is being driven by the kprobes
handlers.
Overall, this is fragile, painful to maintain, and gets in the way of
supporting other things (e.g. RELIABLE_STACKTRACE, FEAT_NMI).
This patch addresses these issues by replacing the kretprobes trampoline
with a `BRK` instruction, and using an exception boundary to acquire and
restore the regs, in the same way as the regular kprobes trampoline.
Ive tested this atop v6.8-rc3:
| KTAP version 1
| 1..1
| KTAP version 1
| # Subtest: kprobes_test
| # module: test_kprobes
| 1..7
| ok 1 test_kprobe
| ok 2 test_kprobes
| ok 3 test_kprobe_missed
| ok 4 test_kretprobe
| ok 5 test_kretprobes
| ok 6 test_stacktrace_on_kretprobe
| ok 7 test_stacktrace_on_nested_kretprobe
| # kprobes_test: pass:7 fail:0 skip:0 total:7
| # Totals: pass:7 fail:0 skip:0 total:7
| ok 1 kprobes_test
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Florent Revest <revest@chromium.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20240208145916.2004154-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When returning to a user context, the arm64 entry code masks all DAIF
exceptions before handling pending work in exit_to_user_mode_prepare()
and do_notify_resume(), where it will transiently unmask all DAIF
exceptions. This is a holdover from the old entry assembly, which
conservatively masked all DAIF exceptions, and it's only necessary to
mask interrupts at this point during the exception return path, so long
as we subsequently mask all DAIF exceptions before the actual exception
return.
While most DAIF manipulation follows a save...restore sequence, the
manipulation in do_notify_resume() is the other way around, unmasking
all DAIF exceptions before masking them again. This is unfortunate as we
unnecessarily mask Debug and SError exceptions, and it would be nice to
remove this special case to make DAIF manipulation simpler and most
consistent.
This patch changes exit_to_user_mode_prepare() and do_notify_resume() to
only mask interrupts while handling pending work, masking other DAIF
exceptions after this has completed. This removes the unusual DAIF
manipulation and allows Debug and SError exceptions to be taken for a
slightly longer window during the exception return path.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
|
|
Currently do_notify_resume() lives in arch/arm64/kernel/signal.c, but it would
make more sense for it to live in entry-common.c as it handles more than
signals, and is coupled with the rest of the return-to-userspace sequence (e.g.
with unusual DAIF masking that matches the exception return requirements).
Move do_notify_resume() to entry-common.c.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-3-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
|
|
In do_notify_resume, we handle _TIF_NEED_RESCHED differently from all
other flags, leaving IRQ+FIQ masked when calling into schedule(). This
masking is a historical artifact, and it is not currently necessary
to mask IRQ+FIQ when calling into schedule (as evidenced by the generic
exit_to_user_mode_loop(), which unmasks IRQs before checking
_TIF_NEED_RESCHED and calling schedule()).
This patch removes the special case for _TIF_NEED_RESCHED, moving this
check into the main loop such that schedule() will be called from a
regular process context with IRQ+FIQ unmasked. This is a minor
simplification to do_notify_resume() and brings it into line with the
generic exit_to_user_mode_loop() logic. This will also aid subsequent
rework of DAIF management.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
|
|
Currently our IO accessors all use register addressing without offsets,
but we could safely use offset addressing (without writeback) to
simplify and optimize the generated code.
To function correctly under a hypervisor which emulates IO accesses, we
must ensure that any faulting/trapped IO access results in an ESR_ELx
value with ESR_ELX.ISS.ISV=1 and with the tranfer register described in
ESR_ELx.ISS.SRT. This means that we can only use loads/stores of a
single general purpose register (or the zero register), and must avoid
writeback addressing modes. However, we can use immediate offset
addressing modes, as these still provide ESR_ELX.ISS.ISV=1 and a valid
ESR_ELx.ISS.SRT when those accesses fault at Stage-2.
Currently we only use register addressing without offsets. We use the
"r" constraint to place the address into a register, and manually
generate the register addressing by surrounding the resulting register
operand with square braces, e.g.
| static __always_inline void __raw_writeq(u64 val, volatile void __iomem *addr)
| {
| asm volatile("str %x0, [%1]" : : "rZ" (val), "r" (addr));
| }
Due to this, sequences of adjacent accesses need to generate addresses
using separate instructions. For example, the following code:
| void writeq_zero_8_times(void *ptr)
| {
| writeq_relaxed(0, ptr + 8 * 0);
| writeq_relaxed(0, ptr + 8 * 1);
| writeq_relaxed(0, ptr + 8 * 2);
| writeq_relaxed(0, ptr + 8 * 3);
| writeq_relaxed(0, ptr + 8 * 4);
| writeq_relaxed(0, ptr + 8 * 5);
| writeq_relaxed(0, ptr + 8 * 6);
| writeq_relaxed(0, ptr + 8 * 7);
| }
... is compiled to:
| <writeq_zero_8_times>:
| str xzr, [x0]
| add x1, x0, #0x8
| str xzr, [x1]
| add x1, x0, #0x10
| str xzr, [x1]
| add x1, x0, #0x18
| str xzr, [x1]
| add x1, x0, #0x20
| str xzr, [x1]
| add x1, x0, #0x28
| str xzr, [x1]
| add x1, x0, #0x30
| str xzr, [x1]
| add x0, x0, #0x38
| str xzr, [x0]
| ret
As described above, we could safely use immediate offset addressing,
which would allow the ADDs to be folded into the address generation for
the STRs, resulting in simpler and smaller generated assembly. We can do
this by using the "o" constraint to allow the compiler to generate
offset addressing (without writeback) for a memory operand, e.g.
| static __always_inline void __raw_writeq(u64 val, volatile void __iomem *addr)
| {
| volatile u64 __iomem *ptr = addr;
| asm volatile("str %x0, %1" : : "rZ" (val), "o" (*ptr));
| }
... which results in the earlier code sequence being compiled to:
| <writeq_zero_8_times>:
| str xzr, [x0]
| str xzr, [x0, #8]
| str xzr, [x0, #16]
| str xzr, [x0, #24]
| str xzr, [x0, #32]
| str xzr, [x0, #40]
| str xzr, [x0, #48]
| str xzr, [x0, #56]
| ret
As Will notes at:
https://lore.kernel.org/linux-arm-kernel/20240117160528.GA3398@willie-the-truck/
... some compilers struggle with a plain "o" constraint, so it's
preferable to use "Qo", where the additional "Q" constraint permits
using non-offset register addressing.
This patch modifies our IO write accessors to use "Qo" constraints,
resulting in the better code generation described above. The IO read
accessors are left as-is because ARM64_WORKAROUND_DEVICE_LOAD_ACQUIRE
requires that non-offset register addressing is used, as the LDAR
instruction does not support offset addressing.
When compiling v6.8-rc1 defconfig with GCC 13.2.0, this saves ~4KiB of
text:
| [mark@lakrids:~/src/linux]% ls -al vmlinux-*
| -rwxr-xr-x 1 mark mark 153960576 Jan 23 12:01 vmlinux-after
| -rwxr-xr-x 1 mark mark 153862192 Jan 23 11:57 vmlinux-before
|
| [mark@lakrids:~/src/linux]% size vmlinux-before vmlinux-after
| text data bss dec hex filename
| 26708921 16690350 622736 44022007 29fb8f7 vmlinux-before
| 26704761 16690414 622736 44017911 29fa8f7 vmlinux-after
... though due to internal alignment of sections, this has no impact on
the size of the resulting Image:
| [mark@lakrids:~/src/linux]% ls -al Image-*
| -rw-r--r-- 1 mark mark 43590144 Jan 23 12:01 Image-after
| -rw-r--r-- 1 mark mark 43590144 Jan 23 11:57 Image-before
Aside from the better code generation, there should be no functional
change as a result of this patch. I have lightly tested this patch,
including booting under KVM (where some devices such as PL011 are
emulated).
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20240124111259.874975-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Arm classifies some of its CPU errata as "rare", indicating that the
hardware error is unlikely to occur in practice. Given that the cost of
errata workarounds can often be significant in terms of power and
performance, don't enable workarounds for "rare" errata by default and
update our documentation to reflect that.
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240209183916.25860-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The patch adding Type-C support for sm6115 was misapplied. All the
orientation switch configuration ended up at the UFS PHY node instead of
the USB PHY node. Move the data bits to the correct place.
Fixes: a06a2f12f9e2 ("arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240220173104.3052778-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.8:
- A tqma8mpql device tree fix to correct audio codec iov-supply.
- A couple of USB-C connector DT description revert to fix regression
on imx8mp-dhcom-pdk3 and imx8mn-var-som-symphony board.
- Fix valid range check for imx-weim bus driver.
- Disable UART4 on Data Modul i.MX8M Plus eDM SBC to avoid boot hang
in case that RDC protection is in place.
* tag 'imx-fixes-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
bus: imx-weim: fix valid range check
Revert "arm64: dts: imx8mn-var-som-symphony: Describe the USB-C connector"
Revert "arm64: dts: imx8mp-dhcom-pdk3: Describe the USB-C connector"
arm64: dts: tqma8mpql: fix audio codec iov-supply
arm64: dts: imx8mp: Disable UART4 by default on Data Modul i.MX8M Plus eDM SBC
Link: https://lore.kernel.org/r/20240206151744.2459-1-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Without the terminator, if a con_id is passed to gpio_find() that
does not exist in the lookup table the function will not stop looping
correctly, and eventually cause an oops.
Cc: stable@vger.kernel.org
Fixes: b2e63555592f ("i2c: gpio: Convert to use descriptors")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20240205102337.439002-1-alexander.sverdlin@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
If the shared_info PFN cache has already been initialized then the content
of the shared_info page needs to be re-initialized whenever the guest
mode is (re)set.
Setting the guest mode is either done explicitly by the VMM via the
KVM_XEN_ATTR_TYPE_LONG_MODE attribute, or implicitly when the guest writes
the MSR to set up the hypercall page.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-12-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
A subsequent patch will allow shared_info to be initialized using either a
GPA or a user-space (i.e. VMM) HVA. To make that patch cleaner, separate
the initialization of the shared_info content from the activation of the
pfncache.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-11-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Rename kvm_is_error_gpa() to kvm_is_gpa_in_memslot() and invert the
polarity accordingly in order to (a) free up kvm_is_error_gpa() to match
with kvm_is_error_{hva,page}(), and (b) to make it more obvious that the
helper is doing a memslot lookup, i.e. not simply checking for INVALID_GPA.
No functional change intended.
Link: https://lore.kernel.org/r/20240215152916.1158-9-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
As noted in [1] the KVM_GUEST_USES_PFN usage flag is never set by any
callers of kvm_gpc_init(), and for good reason: the implementation is
incomplete/broken. And it's not clear that there will ever be a user of
KVM_GUEST_USES_PFN, as coordinating vCPUs with mmu_notifier events is
non-trivial.
Remove KVM_GUEST_USES_PFN and all related code, e.g. dropping
KVM_GUEST_USES_PFN also makes the 'vcpu' argument redundant, to avoid
having to reason about broken code as __kvm_gpc_refresh() evolves.
Moreover, all existing callers specify KVM_HOST_USES_PFN so the usage
check in hva_to_pfn_retry() and hence the 'usage' argument to
kvm_gpc_init() are also redundant.
[1] https://lore.kernel.org/all/ZQiR8IpqOZrOpzHC@google.com
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-6-paul@xen.org
[sean: explicitly call out that guest usage is incomplete]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
At the moment pages are marked dirty by open-coded calls to
mark_page_dirty_in_slot(), directly deferefencing the gpa and memslot
from the cache. After a subsequent patch these may not always be set
so add a helper now so that caller will protected from the need to know
about this detail.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-5-paul@xen.org
[sean: decrease indentation, use gpa_to_gfn()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Sampling gpa and memslot from an unlocked pfncache may yield inconsistent
values so, since there is no problem with calling mark_page_dirty_in_slot()
with the pfncache lock held, relocate the calls in
kvm_xen_update_runstate_guest() and kvm_xen_inject_pending_events()
accordingly.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-4-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The programming protocol for the PAT MSR follows the MTRR programming
protocol. However, this protocol is cumbersome and requires disabling
caching (CR0.CD=1), which is not possible on some platforms.
Specifically, a TDX guest is not allowed to set CR0.CD. It triggers
a #VE exception.
It turns out that the requirement to follow the MTRR programming
protocol for PAT programming is unnecessarily strict. The new Intel
Software Developer Manual (http://www.intel.com/sdm) (December 2023)
relaxes this requirement, please refer to the section titled
"Programming the PAT" for more information.
In short, this section provides an alternative PAT update sequence which
doesn't need to disable caches around the PAT update but only to flush
those caches and TLBs.
The AMD documentation does not link PAT programming to MTRR and is there
fore, fine too.
The kernel only needs to flush the TLB after updating the PAT MSR. The
set_memory code already takes care of flushing the TLB and cache when
changing the memory type of a page.
[ bp: Expand commit message. ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240124130650.496056-1-kirill.shutemov@linux.intel.com
|
|
On s390, currently kernel uses the '-fPIE' compiler flag for compiling
vmlinux. This has a few problems:
- It uses dynamic symbols (.dynsym), for which the linker refuses to
allow more than 64k sections. This can break features which use
'-ffunction-sections' and '-fdata-sections', including kpatch-build
[1] and Function Granular KASLR.
- It unnecessarily uses GOT relocations, adding an extra layer of
indirection for many memory accesses.
Instead of using '-fPIE', resolve all the relocations at link time and
then manually adjust any absolute relocations (R_390_64) during boot.
This is done by first telling the linker to preserve all relocations
during the vmlinux link. (Note this is harmless: they are later
stripped in the vmlinux.bin link.)
Then use the 'relocs' tool to find all absolute relocations (R_390_64)
which apply to allocatable sections. The offsets of those relocations
are saved in a special section which is then used to adjust the
relocations during boot.
(Note: For some reason, Clang occasionally creates a GOT reference, even
without '-fPIE'. So Clang-compiled kernels have a GOT, which needs to
be adjusted.)
On my mostly-defconfig kernel, this reduces kernel text size by ~1.3%.
[1] https://github.com/dynup/kpatch/issues/1284
[2] https://gcc.gnu.org/pipermail/gcc-patches/2023-June/622872.html
[3] https://gcc.gnu.org/pipermail/gcc-patches/2023-August/625986.html
Compiler consideration:
Gcc recently implemented an optimization [2] for loading symbols without
explicit alignment, aligning with the IBM Z ELF ABI. This ABI mandates
symbols to reside on a 2-byte boundary, enabling the use of the larl
instruction. However, kernel linker scripts may still generate unaligned
symbols. To address this, a new -munaligned-symbols option has been
introduced [3] in recent gcc versions. This option has to be used with
future gcc versions.
Older Clang lacks support for handling unaligned symbols generated
by kernel linker scripts when the kernel is built without -fPIE. However,
future versions of Clang will include support for the -munaligned-symbols
option. When the support is unavailable, compile the kernel with -fPIE
to maintain the existing behavior.
In addition to it:
move vmlinux.relocs to safe relocation
When the kernel is built with CONFIG_KERNEL_UNCOMPRESSED, the entire
uncompressed vmlinux.bin is positioned in the bzImage decompressor
image at the default kernel LMA of 0x100000, enabling it to be executed
in-place. However, the size of .vmlinux.relocs could be large enough to
cause an overlap with the uncompressed kernel at the address 0x100000.
To address this issue, .vmlinux.relocs is positioned after the
.rodata.compressed in the bzImage. Nevertheless, in this configuration,
vmlinux.relocs will overlap with the .bss section of vmlinux.bin. To
overcome that, move vmlinux.relocs to a safe location before clearing
.bss and handling relocs.
Compile warning fix from Sumanth Korikkar:
When kernel is built with CONFIG_LD_ORPHAN_WARN and -fno-PIE, there are
several warnings:
ld: warning: orphan section `.rela.iplt' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
ld: warning: orphan section `.rela.head.text' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
ld: warning: orphan section `.rela.init.text' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
ld: warning: orphan section `.rela.rodata.cst8' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
Orphan sections are sections that exist in an object file but don't have
a corresponding output section in the final executable. ld raises a
warning when it identifies such sections.
Eliminate the warning by placing all .rela orphan sections in .rela.dyn
and raise an error when size of .rela.dyn is greater than zero. i.e.
Dont just neglect orphan sections.
This is similar to adjustment performed in x86, where kernel is built
with -fno-PIE.
commit 5354e84598f2 ("x86/build: Add asserts for unwanted sections")
[sumanthk@linux.ibm.com: rebased Josh Poimboeuf patches and move
vmlinux.relocs to safe location]
[hca@linux.ibm.com: merged compile warning fix from Sumanth]
Tested-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219132734.22881-4-sumanthk@linux.ibm.com
Link: https://lore.kernel.org/r/20240219132734.22881-5-sumanthk@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This 'relocs' tool is copied from the x86 version, ported for s390, and
greatly simplified to remove unnecessary features.
It reads vmlinux and outputs assembly to create a .vmlinux.relocs_64
section which contains the offsets of all R_390_64 relocations which
apply to allocatable sections.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219132734.22881-3-sumanthk@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Gcc recently implemented an optimization [1] for loading symbols without
explicit alignment, aligning with the IBM Z ELF ABI. This ABI mandates
symbols to reside on a 2-byte boundary, enabling the use of the larl
instruction. However, kernel linker scripts may still generate unaligned
symbols. To address this, a new -munaligned-symbols option has been
introduced [2] in recent gcc versions.
[1] https://gcc.gnu.org/pipermail/gcc-patches/2023-June/622872.html
[2] https://gcc.gnu.org/pipermail/gcc-patches/2023-August/625986.html
However, when -munaligned-symbols is used in vdso code, it leads to the
following compilation error:
`.data.rel.ro.local' referenced in section `.text' of
arch/s390/kernel/vdso64/vdso64_generic.o: defined in discarded section
`.data.rel.ro.local' of arch/s390/kernel/vdso64/vdso64_generic.o
vdso linker script discards .data section to make it lightweight.
However, -munaligned-symbols in vdso object files references literal
pool and accesses _vdso_data. Hence, compile vdso code without
-munaligned-symbols. This means in the future, vdso code should deal
with alignment of newly introduced unaligned linker symbols.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219132734.22881-2-sumanthk@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
When attempting to boot a kernel compiled with OBJCOPY=llvm-objcopy,
there is a crash right at boot:
Out of memory allocating 6d7800 bytes 8 aligned in range 0:20000000
Reserved memory ranges:
0000000000000000 a394c3c30d90cdaf DECOMPRESSOR
Usable online memory ranges (info source: sclp read info [3]):
0000000000000000 0000000020000000
Usable online memory total: 20000000 Reserved: a394c3c30d90cdaf Free: 0
Call Trace:
(sp:0000000000033e90 [<0000000000012fbc>] physmem_alloc_top_down+0x5c/0x104)
sp:0000000000033f00 [<0000000000011d56>] startup_kernel+0x3a6/0x77c
sp:0000000000033f60 [<00000000000100f4>] startup_normal+0xd4/0xd4
GNU objcopy does not have any issues. Looking at differences between the
object files in each build reveals info.bin does not get properly
populated with llvm-objcopy, which results in an empty .vmlinux.info
section.
$ file {gnu,llvm}-objcopy/arch/s390/boot/info.bin
gnu-objcopy/arch/s390/boot/info.bin: data
llvm-objcopy/arch/s390/boot/info.bin: empty
$ llvm-readelf --section-headers {gnu,llvm}-objcopy/arch/s390/boot/vmlinux | rg 'File:|\.vmlinux\.info|\.decompressor\.syms'
File: gnu-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000078 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034078 035078 000b00 00 WA 0 0 1
File: llvm-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000000 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034000 035000 000b00 00 WA 0 0 1
Ulrich points out that llvm-objcopy only copies sections marked as alloc
with a binary output target, whereas the .vmlinux.info section is only
marked as load. Add 'alloc' in addition to 'load', so that both objcopy
implementations work properly:
$ file {gnu,llvm}-objcopy/arch/s390/boot/info.bin
gnu-objcopy/arch/s390/boot/info.bin: data
llvm-objcopy/arch/s390/boot/info.bin: data
$ llvm-readelf --section-headers {gnu,llvm}-objcopy/arch/s390/boot/vmlinux | rg 'File:|\.vmlinux\.info|\.decompressor\.syms'
File: gnu-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000078 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034078 035078 000b00 00 WA 0 0 1
File: llvm-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000078 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034078 035078 000b00 00 WA 0 0 1
Closes: https://github.com/ClangBuiltLinux/linux/issues/1996
Link: https://github.com/llvm/llvm-project/commit/3c02cb7492fc78fb678264cebf57ff88e478e14f
Suggested-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240216-s390-fix-boot-with-llvm-objcopy-v1-1-0ac623daf42b@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Found and fixed these while working on synchronizing the state
handling of zpci_dev's.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Centralize the removal so all paths are covered and the hotplug slot
will remain active until the device is really destroyed.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
There's a number of tasks that need the state of a zpci device
to be stable. Other tasks need to be synchronized as they change the state.
State changes could be generated by the system as availability or error
events, or be requested by the user through manipulations in sysfs.
Some other actions accessible through sysfs - like device resets - need the
state to be stable.
Unsynchronized state handling could lead to unusable devices. This has
been observed in cases of concurrent state changes through systemd udev
rules and DPM boot control. Some breakage can be provoked by artificial
tests, e.g. through repetitively injecting "recover" on a PCI function
through sysfs while running a "hotplug remove/add" in a loop through a
PCI slot's "power" attribute in sysfs. After a few iterations this could
result in a kernel oops.
So introduce a new mutex "state_lock" to guard the state property of the
struct zpci_dev. Acquire this lock in all task that modify the state:
- hotplug add and remove, through the PCI hotplug slot entry,
- avaiability events, as reported by the platform,
- error events, as reported by the platform,
- during device resets, explicit through sysfs requests or
implict through the common PCI layer.
Break out an inner _do_recover() routine out of recover_store() to
separte the necessary synchronizations from the actual manipulations of
the zpci_dev required for the reset.
With the following changes I was able to run the inject loops for hours
without hitting an error.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Since this guards only the Function Measurement Block, rename from
generic lock to fmb_lock in preparation to introduce another lock
that guards the state member
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Adjust whitespace indentation. No functional change.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
When an event is started, read the current value of the
PAI counter. This value is saved in event::hw.prev_count.
When an event is stopped, this value is subtracted from the current
value read out at event stop time. The difference is the delta
of this counter.
Simplify the logic and read the event value every time the event is
started. This scheme is identical to other device drivers.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
When the PAI events ALL_CRYPTO or ALL_NNPA are created
for system wide sampling, all PAI counters are monitored.
On each process schedule out, the values of all PAI counters
are investigated. Non-zero values are saved in the event's ring
buffer as raw data. This scheme expects the start value of each counter
to be reset to zero after each read operation performed by the PAI
PMU device driver. This allows for only one active event at any one
time as it relies on the start value of counters to be reset to zero.
Create a save area for each installed PAI XXXX_ALL event and save all
PAI counter values in this save area. Instead of clearing the
PAI counter lowcore area to zero after each read operation,
copy them from the lowcore area to the event's save area at process
schedule out time.
The delta of each PAI counter is calculated by subtracting the
old counter's value stored in the event's save area from the current
value stored in the lowcore area.
With this scheme, mulitple events of the PAI counters XXXX_ALL
can be handled at the same time. This will be addressed in a
follow-on patch.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Instead of literal, PCI error value should be set with
PCI_SET_ERROR_RESPONSE(). Use it in tx4927_pci_config_read().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
pci_ops .read/.write must return PCIBIOS_* codes but
tx4927_pci_config_read/write() return -1 when mkaddr() cannot find
devfn from the root bus. Return PCIBIOS_DEVICE_NOT_FOUND instead and
pass that onward in the call chain instead of overwriting the return
value.
Also converts 0 -> PCIBIOS_SUCCESSFUL which has only cosmetic impact.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
pcibios_plat_dev_init() is called from pcibios_enable_device() that
should return normal errnos, not PCIBIOS return codes. In this case the
impact is only cosmetic because PCIBIOS_SUCCESSFUL equals 0 that is
success code with errnos as well. Nonetheless, remove the inconsistency
by replacing the PCIBIOS_SUCCESSFUL with 0.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Ever since introduction in the commit e47d488935ed ("MIPS: Lantiq: Add
PCI controller support.") ltqpci_plat_dev_init has been unused. In
57c8cb8f2429 ("MIPS: pci: convert lantiq driver to OF") also
ltq_pci_plat_arch_init was introduced.
With those commit being more than 10 years ago, it seem neither is
going to get used anytime soon. Thus, remove both unused function
pointer variables.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Now that the driver core can properly handle constant struct bus_type,
move the mips_cdmm_bustype variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
