| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit a263e5f309f32301e1f3ad113293f4e68a82a646 ]
When the CM block migrated from CM2.5 to CM3.0, the address offset for
the Global CSR Access Privilege register was modified. We saw this in
the "MIPS64 I6500 Multiprocessing System Programmer's Guide," it is
stated that "the Global CSR Access Privilege register is located at
offset 0x0120" in section 5.4. It is at least the same for I6400.
This fix allows to use the VP cores in SMP mode if the reset values
were modified by the bootloader.
Based on the work of Vladimir Kondratiev
<vladimir.kondratiev@mobileye.com> and the feedback from Jiaxun Yang
<jiaxun.yang@flygoat.com>.
Fixes: 197e89e0984a ("MIPS: mips-cm: Implement mips_cm_revision")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 59be5c35850171e307ca5d3d703ee9ff4096b948 upstream.
If we still own the FPU after initializing fcr31, when we are preempted
the dirty value in the FPU will be read out and stored into fcr31,
clobbering our setting. This can cause an improper floating-point
environment after execve(). For example:
zsh% cat measure.c
#include <fenv.h>
int main() { return fetestexcept(FE_INEXACT); }
zsh% cc measure.c -o measure -lm
zsh% echo $((1.0/3)) # raising FE_INEXACT
0.33333333333333331
zsh% while ./measure; do ; done
(stopped in seconds)
Call lose_fpu(0) before setting fcr31 to prevent this.
Closes: https://lore.kernel.org/linux-mips/7a6aa1bbdbbe2e63ae96ff163fab0349f58f1b9e.camel@xry111.site/
Fixes: 9b26616c8d9d ("MIPS: Respect the ISA level in FCSR handling")
Cc: stable@vger.kernel.org
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f066a22fe353a827a402ee2835e81f045b1574d upstream
check_bugs() is about to be phased out. Switch over to the new
arch_cpu_finalize_init() implementation.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224545.312438573@linutronix.de
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4897a898a216058dec55e5e5902534e6e224fcdf ]
PAGE_OFFSET is technically a virtual address so when checking the value of
initrd_start against it we should make sure that it has been sanitised from
the values passed by the bootloader. Without this change, even with a bootloader
that passes correct addresses for an initrd, we are failing to load it on MT7621
boards, for example.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91dc288f4edf0d768e46c2c6d33e0ab703403459 ]
When neither LANTIQ nor MIPS_MALTA is set, 'physical_memsize' is not
declared. This causes the build to fail with:
mips-linux-ld: arch/mips/kernel/vpe-mt.o: in function `vpe_run':
arch/mips/kernel/vpe-mt.c:(.text.vpe_run+0x280): undefined reference to `physical_memsize'
LANTIQ is not using 'physical_memsize' and MIPS_MALTA's use of it is
self-contained in mti-malta/malta-dtshim.c.
Use of physical_memsize in vpe-mt.c appears to be unused, so eliminate
this loader mode completely and require VPE programs to be compiled with
DFLT_STACK_SIZE and DFLT_HEAP_SIZE defined.
Fixes: 9050d50e2244 ("MIPS: lantiq: Set physical_memsize")
Fixes: 1a2a6d7e8816 ("MIPS: APRP: Split VPE loader into separate files.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202302030625.2g3E98sY-lkp@intel.com/
Cc: Dengcheng Zhu <dzhu@wavecomp.com>
Cc: John Crispin <john@phrozen.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: "Steven J. Hill" <Steven.Hill@imgtec.com>
Cc: Qais Yousef <Qais.Yousef@imgtec.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0e25498f8cd43c1b5aa327f373dd094e9a006da7 upstream.
There are two big uses of do_exit. The first is it's design use to be
the guts of the exit(2) system call. The second use is to terminate
a task after something catastrophic has happened like a NULL pointer
in kernel code.
Add a function make_task_dead that is initialy exactly the same as
do_exit to cover the cases where do_exit is called to handle
catastrophic failure. In time this can probably be reduced to just a
light wrapper around do_task_dead. For now keep it exactly the same so
that there will be no behavioral differences introducing this new
concept.
Replace all of the uses of do_exit that use it for catastraphic
task cleanup with make_task_dead to make it clear what the code
is doing.
As part of this rename rewind_stack_do_exit
rewind_stack_and_make_dead.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c5ed1fe0801f0c66b0fbce2785239a5664629057 ]
dev_set_name() allocates memory for name, it need be freed
when module exiting, call put_device() to give up reference,
so that it can be freed in kobject_cleanup() when the refcount
hit to 0. The vpe_device is static, so remove kfree() from
vpe_device_release().
Fixes: 17a1d523aa58 ("MIPS: APRP: Add VPE loader support for CMP platforms.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5822e8cc84ee37338ab0bdc3124f6eec04dc232d ]
Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
it need be freed when module exiting, call put_device() to give up
reference, so that it can be freed in kobject_cleanup() when the
refcount hit to 0. The vpe_device is static, so remove kfree() from
vpe_device_release().
Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e1a534f5d074db45ae5cbac41d8912b98e96a006 upstream.
When CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS is selected,
cpu_max_bits_warn() generates a runtime warning similar as below while
we show /proc/cpuinfo. Fix this by using nr_cpu_ids (the runtime limit)
instead of NR_CPUS to iterate CPUs.
[ 3.052463] ------------[ cut here ]------------
[ 3.059679] WARNING: CPU: 3 PID: 1 at include/linux/cpumask.h:108 show_cpuinfo+0x5e8/0x5f0
[ 3.070072] Modules linked in: efivarfs autofs4
[ 3.076257] CPU: 0 PID: 1 Comm: systemd Not tainted 5.19-rc5+ #1052
[ 3.084034] Hardware name: Loongson Loongson-3A4000-7A1000-1w-V0.1-CRB/Loongson-LS3A4000-7A1000-1w-EVB-V1.21, BIOS Loongson-UDK2018-V2.0.04082-beta7 04/27
[ 3.099465] Stack : 9000000100157b08 9000000000f18530 9000000000cf846c 9000000100154000
[ 3.109127] 9000000100157a50 0000000000000000 9000000100157a58 9000000000ef7430
[ 3.118774] 90000001001578e8 0000000000000040 0000000000000020 ffffffffffffffff
[ 3.128412] 0000000000aaaaaa 1ab25f00eec96a37 900000010021de80 900000000101c890
[ 3.138056] 0000000000000000 0000000000000000 0000000000000000 0000000000aaaaaa
[ 3.147711] ffff8000339dc220 0000000000000001 0000000006ab4000 0000000000000000
[ 3.157364] 900000000101c998 0000000000000004 9000000000ef7430 0000000000000000
[ 3.167012] 0000000000000009 000000000000006c 0000000000000000 0000000000000000
[ 3.176641] 9000000000d3de08 9000000001639390 90000000002086d8 00007ffff0080286
[ 3.186260] 00000000000000b0 0000000000000004 0000000000000000 0000000000071c1c
[ 3.195868] ...
[ 3.199917] Call Trace:
[ 3.203941] [<98000000002086d8>] show_stack+0x38/0x14c
[ 3.210666] [<9800000000cf846c>] dump_stack_lvl+0x60/0x88
[ 3.217625] [<980000000023d268>] __warn+0xd0/0x100
[ 3.223958] [<9800000000cf3c90>] warn_slowpath_fmt+0x7c/0xcc
[ 3.231150] [<9800000000210220>] show_cpuinfo+0x5e8/0x5f0
[ 3.238080] [<98000000004f578c>] seq_read_iter+0x354/0x4b4
[ 3.245098] [<98000000004c2e90>] new_sync_read+0x17c/0x1c4
[ 3.252114] [<98000000004c5174>] vfs_read+0x138/0x1d0
[ 3.258694] [<98000000004c55f8>] ksys_read+0x70/0x100
[ 3.265265] [<9800000000cfde9c>] do_syscall+0x7c/0x94
[ 3.271820] [<9800000000202fe4>] handle_syscall+0xc4/0x160
[ 3.281824] ---[ end trace 8b484262b4b8c24c ]---
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4107fa700f314592850e2c64608f6ede4c077476 ]
Add the missing of_node_put() to release the refcount incremented
by of_find_compatible_node().
Signed-off-by: Gong Yuanjun <ruc_gongyuanjun@163.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f0a6c68f69981214cb7858738dd2bc81475111f7 upstream.
Fix the discrepancy between the two places we check for the CP0 counter
erratum in along with the incorrect comparison of the R4400 revision
number against 0x30 which matches none and consistently consider all
R4000 and R4400 processors affected, as documented in processor errata
publications[1][2][3], following the mapping between CP0 PRId register
values and processor models:
PRId | Processor Model
---------+--------------------
00000422 | R4000 Revision 2.2
00000430 | R4000 Revision 3.0
00000440 | R4400 Revision 1.0
00000450 | R4400 Revision 2.0
00000460 | R4400 Revision 3.0
No other revision of either processor has ever been spotted.
Contrary to what has been stated in commit ce202cbb9e0b ("[MIPS] Assume
R4000/R4400 newer than 3.0 don't have the mfc0 count bug") marking the
CP0 counter as buggy does not preclude it from being used as either a
clock event or a clock source device. It just cannot be used as both at
a time, because in that case clock event interrupts will be occasionally
lost, and the use as a clock event device takes precedence.
Compare against 0x4ff in `can_use_mips_counter' so that a single machine
instruction is produced.
References:
[1] "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0", MIPS
Technologies Inc., May 10, 1994, Erratum 53, p.13
[2] "MIPS R4400PC/SC Errata, Processor Revision 1.0", MIPS Technologies
Inc., February 9, 1994, Erratum 21, p.4
[3] "MIPS R4400PC/SC Errata, Processor Revision 2.0 & 3.0", MIPS
Technologies Inc., January 24, 1995, Erratum 14, p.3
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: ce202cbb9e0b ("[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug")
Cc: stable@vger.kernel.org # v2.6.24+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d17b66417308996e7e64b270a3c7f3c1fbd4cfc8 ]
With KCFLAGS="-O3", I was able to trigger a fortify-source
memcpy() overflow panic on set_vi_srs_handler().
Although O3 level is not supported in the mainline, under some
conditions that may've happened with any optimization settings,
it's just a matter of inlining luck. The panic itself is correct,
more precisely, 50/50 false-positive and not at the same time.
From the one side, no real overflow happens. Exception handler
defined in asm just gets copied to some reserved places in the
memory.
But the reason behind is that C code refers to that exception
handler declares it as `char`, i.e. something of 1 byte length.
It's obvious that the asm function itself is way more than 1 byte,
so fortify logics thought we are going to past the symbol declared.
The standard way to refer to asm symbols from C code which is not
supposed to be called from C is to declare them as
`extern const u8[]`. This is fully correct from any point of view,
as any code itself is just a bunch of bytes (including 0 as it is
for syms like _stext/_etext/etc.), and the exact size is not known
at the moment of compilation.
Adjust the type of the except_vec_vi_*() and related variables.
Make set_handler() take `const` as a second argument to avoid
cast-away warnings and give a little more room for optimization.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f2703def339c793674010cc9f01bfe4980231808 ]
After enabling CONFIG_SCHED_CORE (landed during 5.14 cycle),
2-core 2-thread-per-core interAptiv (CPS-driven) started emitting
the following:
[ 0.025698] CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.048183] ------------[ cut here ]------------
[ 0.048187] WARNING: CPU: 1 PID: 0 at kernel/sched/core.c:6025 sched_core_cpu_starting+0x198/0x240
[ 0.048220] Modules linked in:
[ 0.048233] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.17.0-rc3+ #35 b7b319f24073fd9a3c2aa7ad15fb7993eec0b26f
[ 0.048247] Stack : 817f0000 00000004 327804c8 810eb050 00000000 00000004 00000000 c314fdd1
[ 0.048278] 830cbd64 819c0000 81800000 817f0000 83070bf4 00000001 830cbd08 00000000
[ 0.048307] 00000000 00000000 815fcbc4 00000000 00000000 00000000 00000000 00000000
[ 0.048334] 00000000 00000000 00000000 00000000 817f0000 00000000 00000000 817f6f34
[ 0.048361] 817f0000 818a3c00 817f0000 00000004 00000000 00000000 4dc33260 0018c933
[ 0.048389] ...
[ 0.048396] Call Trace:
[ 0.048399] [<8105a7bc>] show_stack+0x3c/0x140
[ 0.048424] [<8131c2a0>] dump_stack_lvl+0x60/0x80
[ 0.048440] [<8108b5c0>] __warn+0xc0/0xf4
[ 0.048454] [<8108b658>] warn_slowpath_fmt+0x64/0x10c
[ 0.048467] [<810bd418>] sched_core_cpu_starting+0x198/0x240
[ 0.048483] [<810c6514>] sched_cpu_starting+0x14/0x80
[ 0.048497] [<8108c0f8>] cpuhp_invoke_callback_range+0x78/0x140
[ 0.048510] [<8108d914>] notify_cpu_starting+0x94/0x140
[ 0.048523] [<8106593c>] start_secondary+0xbc/0x280
[ 0.048539]
[ 0.048543] ---[ end trace 0000000000000000 ]---
[ 0.048636] Synchronize counters for CPU 1: done.
...for each but CPU 0/boot.
Basic debug printks right before the mentioned line say:
[ 0.048170] CPU: 1, smt_mask:
So smt_mask, which is sibling mask obviously, is empty when entering
the function.
This is critical, as sched_core_cpu_starting() calculates
core-scheduling parameters only once per CPU start, and it's crucial
to have all the parameters filled in at that moment (at least it
uses cpu_smt_mask() which in fact is `&cpu_sibling_map[cpu]` on
MIPS).
A bit of debugging led me to that set_cpu_sibling_map() performing
the actual map calculation, was being invocated after
notify_cpu_start(), and exactly the latter function starts CPU HP
callback round (sched_core_cpu_starting() is basically a CPU HP
callback).
While the flow is same on ARM64 (maps after the notifier, although
before calling set_cpu_online()), x86 started calculating sibling
maps earlier than starting the CPU HP callbacks in Linux 4.14 (see
[0] for the reference). Neither me nor my brief tests couldn't find
any potential caveats in calculating the maps right after performing
delay calibration, but the WARN splat is now gone.
The very same debug prints now yield exactly what I expected from
them:
[ 0.048433] CPU: 1, smt_mask: 0-1
[0] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=76ce7cfe35ef
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 18b8f5b6fc53d097cadb94a93d8d6566ba88e389 ]
mips_cm_error_report() extracts the cause and other cause from the error
register using shifts. This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits. Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.
Fix this by using FIELD_GET() instead. Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.
Fixes: 3885c2b463f6a236 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 95bf9d646c3c3f95cb0be7e703b371db8da5be68 upstream.
When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT. This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2]. This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.
Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.
As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Maciej Rozycki <macro@orcam.me.uk>
Cc: linux-mips@vger.kernel.org
[1] 35938a00ba86 ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout")
Cc: stable@vger.kernel.org
Fixes: f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout")
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4b92d4add5f6dcf21275185c997d6ecb800054cd ]
DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.
The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.
This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.
Fixes: 8571890e1513 ("arm64: Add support for ACPI based firmware tables")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8ac7c87acdcac156670f9920c8acbd84308ff4b1 upstream.
MIPS uses its own declaration of rwdata, and thus it should be kept
in sync with the asm-generic one. Currently PAGE_ALIGNED_DATA() is
missing from the linker script, which emits the following ld
warnings:
mips-alpine-linux-musl-ld: warning: orphan section
`.data..page_aligned' from `arch/mips/kernel/vdso.o' being placed
in section `.data..page_aligned'
mips-alpine-linux-musl-ld: warning: orphan section
`.data..page_aligned' from `arch/mips/vdso/vdso-image.o' being placed
in section `.data..page_aligned'
Add the necessary declaration, so the mentioned structures will be
placed in vmlinux as intended:
ffffffff80630580 D __end_once
ffffffff80630580 D __start___dyndbg
ffffffff80630580 D __start_once
ffffffff80630580 D __stop___dyndbg
ffffffff80634000 d mips_vdso_data
ffffffff80638000 d vdso_data
ffffffff80638580 D _gp
ffffffff8063c000 T __init_begin
ffffffff8063c000 D _edata
ffffffff8063c000 T _sinittext
->
ffffffff805a4000 D __end_init_task
ffffffff805a4000 D __nosave_begin
ffffffff805a4000 D __nosave_end
ffffffff805a4000 d mips_vdso_data
ffffffff805a8000 d vdso_data
ffffffff805ac000 D mmlist_lock
ffffffff805ac080 D tasklist_lock
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69e976831cd53f9ba304fd20305b2025ecc78eab upstream.
LLVM-built Linux triggered a boot hangup with KASLR enabled.
arch/mips/kernel/relocate.c:get_random_boot() uses linux_banner,
which is a string constant, as a random seed, but accesses it
as an array of unsigned long (in rotate_xor()).
When the address of linux_banner is not aligned to sizeof(long),
such access emits unaligned access exception and hangs the kernel.
Use PTR_ALIGN() to align input address to sizeof(long) and also
align down the input length to prevent possible access-beyond-end.
Fixes: 405bc8fd12f5 ("MIPS: Kernel: Implement KASLR using CONFIG_RELOCATABLE")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e14f633b66902615cf7faa5d032b45ab8b6fb158 ]
The initialization done by bmips_cpu_setup() typically affects both
threads of a given core, on 7435 which supports 2 cores and 2 threads,
logical CPU number 2 and 3 would not run this initialization.
Fixes: 738a3f79027b ("MIPS: BMIPS: Add early CPU initialization code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9cce844abf07b683cff5f0273977d5f8d0af94c7 upstream.
Now CPU#0 is not hotpluggable on MIPS, so prevent to create /sys/devices
/system/cpu/cpu0/online which confuses some user-space tools.
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ed26aacfb5f71eecb20a ("mips: Add udelay lpj numbers adjustment")
has backported to 4.4~5.4, but the "struct cpufreq_freqs" (and also the
cpufreq notifier machanism) of 4.4~4.19 are different from the upstream
kernel. These differences cause build errors, and this patch can fix the
build.
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Stable <stable@vger.kernel.org> # 4.4/4.9/4.14/4.19
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fcec538ef8cca0ad0b84432235dccd9059c8e6f8 upstream.
This resolves the hazard between the mtc0 in the change_c0_status() and
the mfc0 in configure_exception_vector(). Without resolving this hazard
configure_exception_vector() could read an old value and would restore
this old value again. This would revert the changes change_c0_status()
did. I checked this by printing out the read_c0_status() at the end of
per_cpu_trap_init() and the ST0_MX is not set without this patch.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
Producer | Consumer | Hazard
----------|----------|----------------------------
mtc0 | mfc0 | any coprocessor 0 register
I saw this hazard on an Atheros AR9344 rev 2 SoC with a MIPS 74Kc CPU.
There the change_c0_status() function would activate the DSPen by
setting ST0_MX in the c0_status register. This was reverted and then the
system got a DSP exception when the DSP registers were saved in
save_dsp() in the first process switch. The crash looks like this:
[ 0.089999] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097796] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.107070] Kernel panic - not syncing: Unexpected DSP exception
[ 0.113470] Rebooting in 1 seconds..
We saw this problem in OpenWrt only on the MIPS 74Kc based Atheros SoCs,
not on the 24Kc based SoCs. We only saw it with kernel 5.4 not with
kernel 4.19, in addition we had to use GCC 8.4 or 9.X, with GCC 8.3 it
did not happen.
In the kernel I bisected this problem to commit 9012d011660e ("compiler:
allow all arches to enable CONFIG_OPTIMIZE_INLINING"), but when this was
reverted it also happened after commit 172dcd935c34b ("MIPS: Always
allocate exception vector for MIPSr2+").
Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
does similar changes to a different file. I am not sure if there are
more places affected by this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 31e1b3efa802f97a17628dde280006c4cee4ce5e ]
Register "a1" is unsaved in this function,
when CONFIG_TRACE_IRQFLAGS is enabled,
the TRACE_IRQS_OFF macro will call trace_hardirqs_off(),
and this may change register "a1".
The changed register "a1" as argument will be send
to do_fpe() and do_msa_fpe().
Signed-off-by: YuanJunQing <yuanjunqing66@163.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed26aacfb5f71eecb20a51c4467da440cb719d66 ]
Loops-per-jiffies is a special number which represents a number of
noop-loop cycles per CPU-scheduler quantum - jiffies. As you
understand aside from CPU-specific implementation it depends on
the CPU frequency. So when a platform has the CPU frequency fixed,
we have no problem and the current udelay interface will work
just fine. But as soon as CPU-freq driver is enabled and the cores
frequency changes, we'll end up with distorted udelay's. In order
to fix this we have to accordinly adjust the per-CPU udelay_val
(the same as the global loops_per_jiffy) number. This can be done
in the CPU-freq transition event handler. We subscribe to that event
in the MIPS arch time-inititalization method.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a0efb8b101665a843205eab3d67ab09cb2d9a8d ]
Commit 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache
errors") adds cm2_causes[] array with map of error type ID and
pointers to the short description string. There is a mistake in
the table, since according to MIPS32 manual CM2_ERROR_TYPE = {17,18}
correspond to INTVN_WR_ERR and INTVN_RD_ERR, while the table
claims they have {0x17,0x18} codes. This is obviously hex-dec
copy-paste bug. Moreover codes {0x18 - 0x1a} indicate L2 ECC errors.
Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff487d41036035376e47972c7c522490b839ab37 ]
LLD failed to link vmlinux with 64bit load address for 32bit ELF
while bfd will strip 64bit address into 32bit silently.
To fix LLD build, we should truncate load address provided by platform
into 32bit for 32bit kernel.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/786
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=25784
Reviewed-by: Fangrui Song <maskray@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 269b3a9ac538c4ae87f84be640b9fa89914a2489 ]
In the current code, if CONFIG_SWIOTLB is set, when failed to get IO TLB
memory from the low pages by plat_swiotlb_setup(), it may lead to the boot
process failed with kernel panic.
(1) On the Loongson and SiByte platform
arch/mips/loongson64/dma.c
arch/mips/sibyte/common/dma.c
void __init plat_swiotlb_setup(void)
{
swiotlb_init(1);
}
kernel/dma/swiotlb.c
void __init
swiotlb_init(int verbose)
{
...
vstart = memblock_alloc_low(PAGE_ALIGN(bytes), PAGE_SIZE);
if (vstart && !swiotlb_init_with_tbl(vstart, io_tlb_nslabs, verbose))
return;
...
pr_warn("Cannot allocate buffer");
no_iotlb_memory = true;
}
phys_addr_t swiotlb_tbl_map_single()
{
...
if (no_iotlb_memory)
panic("Can not allocate SWIOTLB buffer earlier ...");
...
}
(2) On the Cavium OCTEON platform
arch/mips/cavium-octeon/dma-octeon.c
void __init plat_swiotlb_setup(void)
{
...
octeon_swiotlb = memblock_alloc_low(swiotlbsize, PAGE_SIZE);
if (!octeon_swiotlb)
panic("%s: Failed to allocate %zu bytes align=%lx\n",
__func__, swiotlbsize, PAGE_SIZE);
...
}
Because IO_TLB_DEFAULT_SIZE is 64M, if the rest size of low memory is less
than 64M when call plat_swiotlb_setup(), we can easily reproduce the panic
case.
In order to reduce the possibility of kernel panic when failed to get IO
TLB memory under CONFIG_SWIOTLB, it is better to allocate low memory as
small as possible before plat_swiotlb_setup(), so make sparse_init() using
top-down allocation.
Reported-by: Juxin Gao <gaojuxin@loongson.cn>
Co-developed-by: Juxin Gao <gaojuxin@loongson.cn>
Signed-off-by: Juxin Gao <gaojuxin@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bef8e2dfceed6daeb6ca3e8d33f9c9d43b926580 upstream.
Pointer on the memory allocated by 'alloc_progmem()' is stored in
'v->load_addr'. So this is this memory that should be freed by
'release_progmem()'.
'release_progmem()' is only a call to 'kfree()'.
With the current code, there is both a double free and a memory leak.
Fix it by passing the correct pointer to 'release_progmem()'.
Fixes: e01402b115ccc ("More AP / SP bits for the 34K, the Malta bits and things. Still wants")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: ralf@linux-mips.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 12051b318bc3ce5b42d6d786191008284b067d83 ]
The code in question is modifying a variable declared const through
pointer manipulation. Such code is explicitly undefined behavior, and
is the lone issue preventing malta_defconfig from booting when built
with Clang:
If an attempt is made to modify an object defined with a const-qualified
type through use of an lvalue with non-const-qualified type, the
behavior is undefined.
LLVM is removing such assignments. A simple fix is to not declare
variables const that you plan on modifying. Limiting the scope would be
a better method of preventing unwanted writes to such a variable.
Further, the code in question mentions "compiler bugs" without any links
to bug reports, so it is difficult to know if the issue is resolved in
GCC. The patch was authored in 2006, which would have been GCC 4.0.3 or
4.1.1. The minimal supported version of GCC in the Linux kernel is
currently 4.6.
For what its worth, there was UB before the commit in question, it just
added a barrier and got lucky IRT codegen. I don't think there's any
actual compiler bugs related, just runtime bugs due to UB.
Link: https://github.com/ClangBuiltLinux/linux/issues/610
Fixes: 966f4406d903 ("[MIPS] Work around bad code generation for <asm/io.h>.")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Debugged-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Eli Friedman <efriedma@quicinc.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Hassan Naveed <hnaveed@wavecomp.com>
Cc: Stephen Kitt <steve@sk2.org>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: clang-built-linux@googlegroups.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b1313eb32c499d46dc4c3e896d19d9564c879c4 ]
Report L1 caches as shared per core; L2 - per cluster.
This fixes "perf" that went crazy if shared_cpu_map attribute not
reported on sysfs, in form of
/sys/devices/system/cpu/cpu*/cache/index*/shared_cpu_list
/sys/devices/system/cpu/cpu*/cache/index*/shared_cpu_map
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4f5cb1a9b27c0f94ef4f5a0178a3fde2d3d0e9e ]
The vectors span more than one byte, so mark them as arrays.
Fixes the following build error when building when using GCC 8.3:
In file included from ./include/linux/string.h:19,
from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./arch/mips/include/asm/processor.h:15,
from ./arch/mips/include/asm/thread_info.h:16,
from ./include/linux/thread_info.h:38,
from ./include/asm-generic/preempt.h:5,
from ./arch/mips/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:81,
from ./include/linux/spinlock.h:51,
from ./include/linux/mmzone.h:8,
from ./include/linux/bootmem.h:8,
from arch/mips/bcm63xx/prom.c:10:
arch/mips/bcm63xx/prom.c: In function 'prom_init':
./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds]
__ret = __builtin_memcpy((dst), (src), __len); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy'
memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
^~~~~~
In file included from arch/mips/bcm63xx/prom.c:14:
./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here
extern char bmips_smp_movevec;
Fixes: 18a1eef92dcd ("MIPS: BMIPS: Introduce bmips.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 38dffe1e4dde1d3174fdce09d67370412843ebb5 upstream.
A Golang developer reported MIPS hwcap isn't reflecting instructions
that the processor actually supported so programs can't apply optimized
code at runtime.
Thus we export the ASEs that can be used in userspace programs.
Reported-by: Meng Zhuo <mengzhuo1203@gmail.com>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org
Cc: Paul Burton <paul.burton@mips.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2f965549006acb865c4638f1f030ebcefdc71f6 upstream.
Recently, binutils had split Loongson-3 Extensions into four ASEs:
MMI, CAM, EXT, EXT2. This patch do the samething in kernel and expose
them in cpuinfo so applications can probe supported ASEs at runtime.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Yunqiang Su <ysu@wavecomp.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 053951dda71ecb4b554a2cdbe26f5f6f9bee9dd2 ]
In order to further reduce power consumption, the XBurst core
by default attempts to avoid branch target buffer lookups by
detecting & special casing loops. This feature will cause
BogoMIPS and lpj calculate in error. Set cp0 config7 bit 4 to
disable this feature.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: ralf@linux-mips.org
Cc: paul@crapouillou.net
Cc: jhogan@kernel.org
Cc: malat@debian.org
Cc: gregkh@linuxfoundation.org
Cc: tglx@linutronix.de
Cc: allison@lohutok.net
Cc: syq@debian.org
Cc: chenhc@lemote.com
Cc: jiaxun.yang@flygoat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8bea8a5e5d942e62203416ab41edecaed4fda02 ]
Because CONFIG_OF defined for MIPS, cacheinfo attempts to fill information
from DT, ignoring data filled by architecture routine. This leads to error
reported
cacheinfo: Unable to detect cache hierarchy for CPU 0
Way to fix this provided in
commit fac51482577d ("drivers: base: cacheinfo: fix x86 with
CONFIG_OF enabled")
Utilize same mechanism to report that cacheinfo set by architecture
specific function
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a07e3324538a989b7cdbf2c679be6a7f9df2544f ]
i8253 clocksource needs a free running timer. This could only
be used, if i8253 clockevent is set up as periodic.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f532beeeff0c0a3586cc15538bc52d249eb19e7c ]
Fixes gcc '-Wunused-but-set-variable' warning:
arch/mips/kernel/uprobes.c: In function 'arch_uprobe_pre_xol':
arch/mips/kernel/uprobes.c:115:17: warning: variable 'epc' set but not used [-Wunused-but-set-variable]
It's never used since introduction in
commit 40e084a506eb ("MIPS: Add uprobes support.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <linux-mips@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93fa5b280761a4dbb14c5330f260380385ab2b49 ]
There are situations when memory regions coming from dts may be
too big for the platform physical address space. This especially
concerns XPA-capable systems. Bootloader may determine more than 4GB
memory available and pass it to the kernel over dts memory node, while
kernel is built without XPA/64BIT support. In this case the region
may either simply be truncated by add_memory_region() method
or by u64->phys_addr_t type casting. But in worst case the method
can even drop the memory region if it exceeds PHYS_ADDR_MAX size.
So lets make sure the retrieved from dts memory regions are valid,
and if some of them aren't, just manually truncate them with a warning
printed out.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Serge Semin <Sergey.Semin@t-platforms.ru>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e9666d10a5677a494260d60d1fa0b73cc7646eb3 upstream.
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
[nc: Fix trivial conflicts in 4.19
arch/xtensa/kernel/jump_label.c doesn't exist yet
Ensured CC_HAVE_ASM_GOTO and HAVE_JUMP_LABEL were sufficiently
eliminated]
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b1f01b653b408ebe58fec78c566d1075d285c64 upstream.
arch/mips/kernel/perf_event_mipsxx.c: In function 'mipsxx_pmu_enable_event':
arch/mips/kernel/perf_event_mipsxx.c:326:21: error: unused variable 'event' [-Werror=unused-variable]
struct perf_event *event = container_of(evt, struct perf_event, hw);
^~~~~
Fix this by making use of IS_ENABLED() to simplify the code and avoid
unnecessary ifdefery.
Fixes: 84002c88599d ("MIPS: perf: Fix perf with MT counting other threads")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ab8a6d821179ab9bea1a9179f535ccba6330c1ed ]
KGDB_call_nmi_hook is called by other cpu through smp call.
MIPS smp call is processed in ipi irq handler and regs is saved in
handle_int.
So kgdb_call_nmi_hook get regs by get_irq_regs and regs will be passed
to kgdb_cpu_enter.
Signed-off-by: Chong Qiao <qiaochong@loongson.cn>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: QiaoChong <qiaochong@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 79b4a9cf0e2ea8203ce777c8d5cfa86c71eae86e upstream.
Commit 4c21b8fd8f14 (MIPS: seccomp: Handle indirect system calls (o32))
added indirect syscall detection for O32 processes running on MIPS64,
but it did not work correctly for big endian kernel/processes. The
reason is that the syscall number is loaded from ARG1 using the lw
instruction while this is a 64-bit value, so zero is loaded instead of
the syscall number.
Fix the code by using the ld instruction instead. When running a 32-bit
processes on a 64 bit CPU, the values are properly sign-extended, so it
ensures the value passed to syscall_trace_enter is correct.
Recent systemd versions with seccomp enabled whitelist the getpid
syscall for their internal processes (e.g. systemd-journald), but call
it through syscall(SYS_getpid). This fix therefore allows O32 big endian
systems with a 64-bit kernel to run recent systemd versions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: <stable@vger.kernel.org> # v3.15+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f0a53bc6482fb09770982a8447981260ea258dc upstream.
This fixes booting with the combination of CONFIG_RELOCATABLE=y
and CONFIG_MIPS_ELF_APPENDED_DTB=y.
Sections that appear after the relocation table are not relocated
on system boot (except .bss, which has special handling).
With CONFIG_MIPS_ELF_APPENDED_DTB, the dtb is part of the
vmlinux ELF, so it must be relocated together with everything else.
Fixes: 069fd766271d ("MIPS: Reserve space for relocation table")
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2b424cfc69728224fcb5fad138ea7260728e0901 ]
Patch (b6c7a324df37b "MIPS: Fix get_frame_info() handling of
microMIPS function size.") introduces additional function size
check for microMIPS by only checking insn between ip and ip + func_size.
However, func_size in get_frame_info() is always 0 if KALLSYMS is not
enabled. This causes get_frame_info() to return immediately without
calculating correct frame_size, which in turn causes "Can't analyze
schedule() prologue" warning messages at boot time.
This patch removes func_size check, and let the frame_size check run
up to 128 insns for both MIPS and microMIPS.
Signed-off-by: Jun-Ru Chang <jrjang@realtek.com>
Signed-off-by: Tony Wu <tonywu@realtek.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6c7a324df37b ("MIPS: Fix get_frame_info() handling of microMIPS function size.")
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <macro@mips.com>
Cc: <yamada.masahiro@socionext.com>
Cc: <peterz@infradead.org>
Cc: <mingo@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 72faa7a773ca59336f3c889e878de81445c5a85c upstream.
The irq_pages is the number of pages for irq stack, but not the
order which is needed by __get_free_pages().
We can use get_order() to calculate the accurate order.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: fe8bd18ffea5 ("MIPS: Introduce irq_stack")
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94ee12b507db8b5876e31c9d6c9d84f556a4b49f upstream.
__cmpxchg_small erroneously uses u8 for load comparison which can
be either char or short. This patch changes the local variable to
u32 which is sufficiently sized, as the loaded value is already
masked and shifted appropriately. Using an integer size avoids
any unnecessary canonicalization from use of non native widths.
This patch is part of a series that adapts the MIPS small word
atomics code for xchg and cmpxchg on short and char to RISC-V.
Cc: RISC-V Patches <patches@groups.riscv.org>
Cc: Linux RISC-V <linux-riscv@lists.infradead.org>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Signed-off-by: Michael Clark <michaeljclark@mac.com>
[paul.burton@mips.com:
- Fix varialble typo per Jonas Gorski.
- Consolidate load variable with other declarations.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3ba7f44d2b19 ("MIPS: cmpxchg: Implement 1 byte & 2 byte cmpxchg()")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 05dc6001af0630e200ad5ea08707187fe5537e6d upstream.
Accordingly to the documentation
---cut---
The GCR_ERROR_CAUSE.ERR_TYPE field and the GCR_ERROR_MULT.ERR_TYPE
fields can be cleared by either a reset or by writing the current
value of GCR_ERROR_CAUSE.ERR_TYPE to the
GCR_ERROR_CAUSE.ERR_TYPE register.
---cut---
Do exactly this. Original value of cm_error may be safely written back;
it clears error cause and keeps other bits untouched.
Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit adcc81f148d733b7e8e641300c5590a2cdc13bf3 upstream.
Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")
Cc: stable@vger.kernel.org # v4.8+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rich Felker <dalias@libc.org>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8712b27c5723c26400a2b350faf1d6d9fd7ffaad upstream.
The function_graph_enter() function does the work of calling the function
graph hook function and the management of the shadow stack, simplifying the
work done in the architecture dependent prepare_ftrace_return().
Have MIPS use the new code, and remove the shadow stack management as well as
having to set up the trace structure.
This is needed to prepare for a fix of a design bug on how the curr_ret_stack
is used.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: stable@kernel.org
Fixes: 03274a3ffb449 ("tracing/fgraph: Adjust fgraph depth before calling trace return callback")
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dc57aaf95a516f70e2d527d8287a0332c481a226 ]
After changing CPU online status, it will not be sent any IPIs such as in
__flush_cache_all() on software coherency systems. Do this before disabling
local IRQ.
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20571/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: rachel.mozes@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
