summaryrefslogtreecommitdiff
path: root/arch/arm/boot
AgeCommit message (Collapse)Author
2021-03-30ARM: dts: imx6: pbab01: Set vmmc supply for both SD interfacesStefan Riedmueller
Setting the vmmc supplies is crucial since otherwise the supplying regulators get disabled and the SD interfaces are no longer powered which leads to system failures if the system is booted from that SD interface. Fixes: 1e44d3f880d5 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module") Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-03-30ARM: dts: imx6: pbab01: Set USB OTG port to peripheralStefan Riedmueller
Due to a hardware bug preventing the correct detection if the ID pin the USB OTG port cannot be used in otg mode. It can either be set to host or peripheral. Set it to peripheral so vbus is disabled by default. Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-03-30ARM: dts: imx6: pfla02: Fix USB vbus enable pinmuxingStefan Riedmueller
The pinmuxing for the enable pin of the usbh1 node is wrong. It needs to be muxed as GPIO. While at it, move the pinctrl to the vbus regulator since it is actually the regulator enable pin. Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-03-29ARM: dts: BCM5301X: Set Linksys EA9500 power LEDRafał Miłecki
Set Linux default trigger to default on, just like it's normally done for power LEDs. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-03-29ARM: dts: BCM5301X: Fix Linksys EA9500 partitionsRafał Miłecki
Partitions are basically fixed indeed but firmware ones don't have hardcoded function ("firmware" vs "failsafe"). Actual function depends on bootloader configuration. Use a proper binding for that. While at it fix numbers formatting to avoid: arch/arm/boot/dts/bcm47094-linksys-panamera.dt.yaml: partitions: 'partition@1F00000' does not match any of the regexes: '^partition@[0-9a-f]+$', 'pinctrl-[0-9]+' From schema: Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-03-29arm: dts: mt2701: harmonize node names and compatiblesChunfeng Yun
This is used to fix dtbs_check warning Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20210316092232.9806-13-chunfeng.yun@mediatek.com Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2021-03-29arm: dts: mt7623: harmonize node names and compatiblesChunfeng Yun
This is used to fix dtbs_check warning Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20210316092232.9806-12-chunfeng.yun@mediatek.com Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2021-03-29arm: dts: mt7629: harmonize node names and compatiblesChunfeng Yun
This is used to fix dtbs_check warning Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20210316092232.9806-11-chunfeng.yun@mediatek.com Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2021-03-29ARM: dts: stm32: enable the analog filter for all I2C nodes in stm32mp151Alain Volmat
Enable the analog filter for all I2C nodes of the stm32mp151. Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-03-29ARM: imx7d-remarkable2: Initial device tree for reMarkable2Alistair Francis
The reMarkable2 (https://remarkable.com) is an e-ink tablet based on the imx7d SoC. This commit is based on the DTS provide by reMarkable but ported to the latest kernel (instead of 4.14). I have removed references to non-upstream devices and have changed the UART so that the console can be accessed without having to open up the device via the OTG pogo pins. Currently the kernel boots, but there is no support for the display. WiFi is untested (no display or UART RX makes it hard to test), but should work with the current upstream driver. As it's untested it's not included in this commit. Signed-off-by: Alistair Francis <alistair@alistair23.me> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-03-28ARM: dts: exynos: Add front camera support to I9100Timon Baetz
Add node for Samsung S5K5BAF CMOS image sensor and enable the associated MIPI CSI-2 receiver node. Signed-off-by: Timon Baetz <timon.baetz@protonmail.com> Link: https://lore.kernel.org/r/20210327200851.777327-1-timon.baetz@protonmail.com [krzk: put csis_1 node in alphabetical order] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-03-27ARM: dts: ux500: Clarify UIB version per boardLinus Walleij
Make it clear which UIB is used with each board in comments and model text. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-27ARM: dts: ux500: Totally separate TVK R2 and R3Linus Walleij
There is no point in sharing any definitions between the R2 and R3 versions of the TVK1281618 UIB. The proximity sensor collides with the touchscreen etc, it is less confusing to get rid of the overarching TVK1281618 UIB file and just use one for each. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-27ARM: dts: ux500: Push TC35893 defines to each UIBLinus Walleij
The TC35893 is connected to different GPIOs in different UIBs so just bite the bullet and push this info down into respective UIB so we can avoid confusion when reading the DTS files. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-26ARM: tegra: acer-a500: Add atmel,wakeup-method propertyDmitry Osipenko
Acer A500 uses Atmel Maxtouch 1386 touchscreen controller. This controller has WAKE line which could be connected to I2C clock lane, dedicated GPIO or fixed to HIGH level. Controller wakes up from a deep sleep when WAKE line is asserted low. Acer A500 has WAKE line connected to I2C clock and Linux device driver doesn't work property without knowing what wakeup method is used by h/w. Add atmel,wakeup-method property to the touchscreen node. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> [treding@nvidia.com: use literal to avoid dependency on header file] Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-26ARM: dts: ux500: Fix up TVK R3 sensorsLinus Walleij
The TVK1281618 R3 sensors are different from the R2 board, some incorrectness is fixed and some new sensors added, we also rename the nodes appropriately with accelerometer@ etc. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-26ARM: dts: ux500: Push sensors to TVK R2 boardLinus Walleij
These sensors are particular to the TVK UIB R2 board and will conflict with the R3 board, so push them down to the actual UIB include DTSI. Rename the nodes appropriately to accelerometer@ etc in the process. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-26ARM: dts: ux500: Move Synaptics to right includeLinus Walleij
The Synaptics RMI4 touchscreen is a property of the TVK1281618 R2 UIB, so move it into that file instead of the main TVK1281618 main include so we can define another touchscreen for the R3 UIB. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-26ARM: dts: ux500: Fix touchscreen on TVK R2Linus Walleij
The touchscreen is mounted with flipped x/y on the R2 version of TVK1281618. Push this setting to that DTS file only. The function nodes were named wrong so the OF properties didn not "take". Fix the node names from "rmi-fnn" to "rmi4-nn" so this also work. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-03-26ARM: dts: ux500: Fix BT+WLAN on JaniceLinus Walleij
GPIO215 has a rail named WLAN_RST_N but it is actually connected to the pin WLAN_REG_ON on the BCM4330 chip, so this should be the WLAN regulator GPIO rather than GPIO222. The misunderstanding comes from the erroneous naming of the rail on the schematic. GPIO222 is indeed connected to the rail BT_VREG_EN and the pin BT_REG_ON, and can be handled by the driver as usual. This corrects misunderstandings and makes Janice's WLAN and BT setup look like that of Golden and Skomer. Add explicit BCM4330 compatible to the WLAN chip. Cc: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
2021-03-25ARM: dts: BCM5301X: Describe NVMEM NVRAM on Linksys & Luxul routersRafał Miłecki
Provide access to NVRAM which contains device environment variables. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-03-25ARM: dts: BCM5301X: fix "reg" formatting in /memory nodeRafał Miłecki
This fixes warnings/errors like: arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dt.yaml: /: memory@0:reg:0: [0, 134217728, 2281701376, 402653184] is too long From schema: /lib/python3.6/site-packages/dtschema/schemas/reg.yaml Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-03-25ARM: dts: rockchip: remove clock-names property from watchdog node in ↵Johan Jonker
rv1108.dtsi A test with the command below gives this error: /arch/arm/boot/dts/rv1108-evb.dt.yaml: watchdog@10360000: clock-names:0: 'tclk' was expected Comment from the dw_wdt.c file: Try to request the watchdog dedicated timer clock source. It must be supplied if asynchronous mode is enabled. Otherwise fallback to the common timer/bus clocks configuration, in which the very first found clock supply both timer and APB signals. Like in the other Rockchip watchdog nodes the property "clock-names" is not needed, so remove it. make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20201218120534.13788-8-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2021-03-25ARM: dts: rockchip: add new watchdog compatible to rk322x.dtsiJohan Jonker
The watchdog compatible strings are suppose to be SoC orientated. In the more recently added Rockchip rk322x.dtsi file only the fallback string "snps,dw-wdt" is used, so add the new compatible string: "rockchip,rk3228-wdt", "snps,dw-wdt" make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20201218120534.13788-3-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2021-03-25ARM: dts: rockchip: add new watchdog compatible to rv1108.dtsiJohan Jonker
The watchdog compatible strings are suppose to be SoC orientated. In the more recently added Rockchip rv1108.dtsi file only the fallback string "snps,dw-wdt" is used, so add the new compatible string: "rockchip,rv1108-wdt", "snps,dw-wdt" make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20201218120534.13788-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2021-03-24ARM: dts: motorola-cpcap-mapphone: Prepare for dtbs_check parsingSebastian Reichel
'<&gpio1 parameters &gpio2 parameters>' and '<&gpio1 parameters>, <&gpio2 parameters>' result in the same DTB, but second format has better source code readability. Also 'dtbs_check' currently uses this format to determine the amount of items specified, so using this syntax is needed to successfully verify the devicetree source against a DT schema format. Cc: linux-omap@vger.kernel.org Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-03-24ARM: dts: am33xx-l4: fix tscadc@0 node indentationDario Binacchi
Fix the broken indentation of tscadc@0 node. Signed-off-by: Dario Binacchi <dariobin@libero.it> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-03-24ARM: dts: omap3-echo: Add ath6kl nodeAndré Hentschel
Add ath6kl node. Signed-off-by: André Hentschel <nerv@dawncrow.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-03-24ARM: dts: omap3-echo: Update LED configurationAndré Hentschel
Update LED configuration. Signed-off-by: André Hentschel <nerv@dawncrow.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-03-24ARM: dts: am335x-pocketbeagle: unique gpio-line-namesDrew Fustini
Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected". [1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/ Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Drew Fustini <drew@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-03-24ARM: tegra: Specify tps65911 as wakeup sourceDmitry Osipenko
Specify TPS65911 as wakeup source on Tegra devices in order to allow its RTC to wake up system from suspend by default instead of requiring wakeup to be enabled manually via sysfs. Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30 Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30 Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: Specify memory suspend OPP in device-treeDmitry Osipenko
Specify memory suspend OPP in a device-tree, just for consistency. Now memory will always suspend on the same frequency. Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30 Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30 Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30 Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: Specify CPU suspend OPP in device-treeDmitry Osipenko
Specify CPU suspend OPP in a device-tree, just for consistency. Now CPU will always suspend on the same frequency. Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30 Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30 Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30 Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: ouya: Specify all CPU cores as cooling devicesDmitry Osipenko
If CPU0 is unplugged the cooling device can not rebind to CPU1. And if CPU0 is plugged in again, the cooling device may fail to initialize. If the CPUs are mapped with the physical CPU0 to Linux numbering CPU1, the cooling device mapping will fail. Hence specify all CPU cores as a cooling devices in the device-tree. Tested-by: Peter Geis <pgwipeout@gmail.com> Tested-by: Matt Merhar <mattmerhar@protonmail.com> Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: nexus7: Specify all CPU cores as cooling devicesDmitry Osipenko
If CPU0 is unplugged the cooling device can not rebind to CPU1. And if CPU0 is plugged in again, the cooling device may fail to initialize. If the CPUs are mapped with the physical CPU0 to Linux numbering CPU1, the cooling device mapping will fail. Hence specify all CPU cores as a cooling devices in the device-tree. Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: acer-a500: Rename avdd to vdda of touchscreen nodeDmitry Osipenko
Rename avdd supply to vdda of the touchscreen node. The old supply name was incorrect. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: acer-a500: Specify all CPU cores as cooling devicesDmitry Osipenko
If CPU0 is unplugged the cooling device can not rebind to CPU1. And if CPU0 is plugged in again, the cooling device may fail to initialize. If the CPUs are mapped with the physical CPU0 to Linux numbering CPU1, the cooling device mapping will fail. Hence specify all CPU cores as a cooling devices in the device-tree. Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: acer-a500: Reduce thermal throttling hysteresis to 0.2CDmitry Osipenko
The 2C hysteresis is a bit too high, although CPU never gets hot on A500. Nevertheless, let's reduce thermal throttling hysteresis to 0.2C, which is a much more reasonable value. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: acer-a500: Enable core voltage scalingDmitry Osipenko
Allow lower core voltages on Acer A500. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: paz00: Enable full voltage scaling ranges for CPU and Core domainsDmitry Osipenko
Enable full voltage scaling ranges for CPU and Core power domains. Tested-by: Nicolas Chauvet <kwizart@gmail.com> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: cardhu: Support CPU thermal throttlingDmitry Osipenko
Enable CPU thermal throttling on Tegra30 Cardhu board. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: cardhu: Support CPU frequency and voltage scaling on all board ↵Dmitry Osipenko
variants Enable CPU frequency and voltage scaling on all Tegra30 Cardhu board variants. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: ventana: Support CPU thermal throttlingDmitry Osipenko
Enable CPU thermal throttling on Tegra20 Ventana board. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: tegra: ventana: Support CPU and Core voltage scalingDmitry Osipenko
Support CPU and Core voltage scaling on Tegra20 Ventana board. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-03-24ARM: dts: Fix swapped mmc order for omap3Tony Lindgren
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped around with commit 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4"). Let's fix the issue with aliases as discussed on the mailing lists. While the mmc aliases should be board specific, let's first fix the issue with minimal changes. Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-03-24ARM: dts: koelsch: Configure pull-up for SOFT_SW GPIO keysGeert Uytterhoeven
The GPIO pins connected to the 4 Software Switches ("SOFT_SW", SW2) do not have external pull-up resistors, but rely on internal pull-ups being enabled. Fortunately this is satisfied by the initial state of these pins. Make this explicit by enabling bias-pull-up, to remove the dependency on initial state and/or boot loader configuration. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/20210303132941.3938516-1-geert+renesas@glider.be
2021-03-24ARM: dts: sun8i: h3: beelink-x2: Add power buttonJernej Skrabec
Beelink X2 has power button. Add node for it. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210323204341.28825-1-jernej.skrabec@siol.net
2021-03-23ARM: socfpga: introduce common ARCH_INTEL_SOCFPGAKrzysztof Kozlowski
Simplify 32-bit and 64-bit Intel SoCFPGA Kconfig options by having only one for both of them. This the common practice for other platforms. Additionally, the ARCH_SOCFPGA is too generic as SoCFPGA designs come from multiple vendors. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2021-03-23ARM: dts: stm32: Add wakeup management on stm32mp15x UART nodesErwan Le Ray
Add EXTI lines to the following UART nodes which are used for wakeup from CStop. - EXTI line 26 to USART1 - EXTI line 27 to USART2 - EXTI line 28 to USART3 - EXTI line 29 to USART6 - EXTI line 30 to UART4 - EXTI line 31 to UART5 - EXTI line 32 to UART7 - EXTI line 33 to UART8 Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Link: https://lore.kernel.org/r/20210319184253.5841-6-erwan.leray@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-19ARM: dts: exynos: white-space cleanupsKrzysztof Kozlowski
Fixups some white-space issues. Checkpatch reported: WARNING: Block comments should align the * on each line WARNING: please, no spaces at the start of a line ERROR: code indent should use tabs where possible Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20210315124313.114842-2-krzysztof.kozlowski@canonical.com
generated by cgit v1.2.3 (git 2.51.0) at 2026-11-08 07:16:31 +0000