| Age | Commit message (Collapse) | Author |
|---|
|
We have observed an NFSv4 client receiving a LOCK reply with a status of
NFS4ERR_OLD_STATEID and subsequently retrying the LOCK request with an
earlier seqid value in the stateid. As this was for a new lockowner,
that would imply that nfs_set_open_stateid_locked() had updated the open
stateid seqid with an earlier value.
Looking at nfs_set_open_stateid_locked(), if the incoming seqid is out
of sequence, the task will sleep on the state->waitq for up to 5
seconds. If the task waits for the full 5 seconds, then after finishing
the wait it'll update the open stateid seqid with whatever value the
incoming seqid has. If there are multiple waiters in this scenario,
then the last one to perform said update may not be the one with the
highest seqid.
Add a check to ensure that the seqid can only be incremented, and add a
tracepoint to indicate when old seqids are skipped.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@hammerspace.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Fixes for the Allwinner A523 clk driver:
- Lower the minimum rate for the A523 audio PLL to support
frequencies required by audio devices
- Mark a couple clks critical on A523 so that Linux doesn't turn them
off when they're used by other code like TF-A"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: sun55i-a523-ccu: Lower audio0 pll minimum rate
clk: sunxi-ng: sun55i-a523-r-ccu: Mark bus-r-dma as critical
clk: sunxi-ng: Mark A523 bus-r-cpucfg clock as critical
|
|
This adds the two PWM-controlled fans of the HiFive Unmatched board to
the device tree.
Signed-off-by: René Rebe <rene@exactco.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
- Fix a race in timer->function clearing in timer_shutdown_sync()
- Fix a timekeeper sysfs-setup resource leak in error paths
- Fix the NOHZ report_idle_softirq() syslog rate-limiting
logic to have no side effects on the return value
* tag 'timers-urgent-2025-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix NULL function pointer race in timer_shutdown_sync()
timekeeping: Fix resource leak in tk_aux_sysfs_init() error paths
tick/sched: Fix bogus condition in report_idle_softirq()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Fix perf CPU-clock counters, and address a static checker warning"
* tag 'perf-urgent-2025-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix 0 count issue of cpu-clock
perf/x86/intel/uncore: Remove superfluous check
|
|
Use min() to improve the readability of actmon_cpu_to_emc_rate() and
remove any unnecessary curly braces.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20251112172121.3741-2-thorsten.blum@linux.dev/
|
|
Ensure all required data is acquired before calling dev_pm_opp_put(opp)
to maintain correct resource acquisition and release order.
Fixes: 7da2fdaaa1e6 ("PM / devfreq: Add HiSilicon uncore frequency scaling driver")
Signed-off-by: Pengjie Zhang <zhangpengjie2@huawei.com>
Reviewed-by: Jie Zhan <zhanjie9@hisilicon.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20250915062135.748653-1-zhangpengjie2@huawei.com/
|
|
Some device drivers (and out-of-tree modules) might want to define
device-specific device governors. Rather than restricting all of them to
be a part of drivers/devfreq/ (which is not possible for out-of-tree
drivers anyway) move governor.h to include/linux/devfreq-governor.h and
update all drivers to use it.
The devfreq_cpu_data is only used internally, by the passive governor,
so it is moved to the driver source rather than being a part of the
public interface.
Reported-by: Robie Basak <robibasa@qti.qualcomm.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://patchwork.kernel.org/project/linux-pm/patch/20251030-governor-public-v2-1-432a11a9975a@oss.qualcomm.com/
|
|
The documentation of that function promises to never sleep. However on
PREEMPT_RT a spinlock_t might in fact sleep.
Reword the documentation so users can predict its behavior better.
mempool could also replace spinlock_t with raw_spinlock_t which doesn't
sleep even on PREEMPT_RT but that would take away the improved
preemptibility of sleeping locks.
Link: https://lkml.kernel.org/r/20251014-mempool-doc-v1-1-bc9ebf169700@linutronix.de
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@gentwo.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Vishal Moola (Oracle)" <vishal.moola@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Mentioning the name of the file is redundant, so drop it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113084022.1255121-12-hch@lst.de
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Switch all uses of the deprecated mempool_t typedef in the core mempool
code to use struct mempool instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113084022.1255121-11-hch@lst.de
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
This was added for bcachefs and is unused now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113084022.1255121-10-hch@lst.de
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
The timeout here is and old workaround with a Fixme comment. But
thinking about it, it makes sense to keep it, so reword the comment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113084022.1255121-9-hch@lst.de
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Add a version of the mempool allocator that works for batch allocations
of multiple objects. Calling mempool_alloc in a loop is not safe because
it could deadlock if multiple threads are performing such an allocation
at the same time.
As an extra benefit the interface is build so that the same array can be
used for alloc_pages_bulk / release_pages so that at least for page
backed mempools the fast path can use a nice batch optimization.
Note that mempool_alloc_bulk does not take a gfp_mask argument as it
must always be able to sleep and doesn't support any non-trivial
modifiers. NOFO or NOIO constrainst must be set through the scoped API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113084022.1255121-8-hch@lst.de
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Add a helper for the mempool_alloc slowpath to better separate it from the
fast path, and also use it to implement mempool_alloc_preallocated which
shares the same logic.
[hughd@google.com: fix lack of retrying with __GFP_DIRECT_RECLAIM]
[vbabka@suse.cz: really use limited flags for first mempool attempt]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113084022.1255121-7-hch@lst.de
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
There is a race condition between timer_shutdown_sync() and timer
expiration that can lead to hitting a WARN_ON in expire_timers().
The issue occurs when timer_shutdown_sync() clears the timer function
to NULL while the timer is still running on another CPU. The race
scenario looks like this:
CPU0 CPU1
<SOFTIRQ>
lock_timer_base()
expire_timers()
base->running_timer = timer;
unlock_timer_base()
[call_timer_fn enter]
mod_timer()
...
timer_shutdown_sync()
lock_timer_base()
// For now, will not detach the timer but only clear its function to NULL
if (base->running_timer != timer)
ret = detach_if_pending(timer, base, true);
if (shutdown)
timer->function = NULL;
unlock_timer_base()
[call_timer_fn exit]
lock_timer_base()
base->running_timer = NULL;
unlock_timer_base()
...
// Now timer is pending while its function set to NULL.
// next timer trigger
<SOFTIRQ>
expire_timers()
WARN_ON_ONCE(!fn) // hit
...
lock_timer_base()
// Now timer will detach
if (base->running_timer != timer)
ret = detach_if_pending(timer, base, true);
if (shutdown)
timer->function = NULL;
unlock_timer_base()
The problem is that timer_shutdown_sync() clears the timer function
regardless of whether the timer is currently running. This can leave a
pending timer with a NULL function pointer, which triggers the
WARN_ON_ONCE(!fn) check in expire_timers().
Fix this by only clearing the timer function when actually detaching the
timer. If the timer is running, leave the function pointer intact, which is
safe because the timer will be properly detached when it finishes running.
Fixes: 0cc04e80458a ("timers: Add shutdown mechanism to the internal functions")
Signed-off-by: Yipeng Zou <zouyipeng@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251122093942.301559-1-zouyipeng@huawei.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- Fix CPU type in DT for econet
- Fix for Malta PCI MMIO breakage for SOC-it
- Fix TLB shutdown caused by iniital uniquification
- Fix random seg faults due to missed vdso storage requirement
* tag 'mips-fixes_6.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kernel: Fix random segmentation faults
MIPS: mm: Prevent a TLB shutdown on initial uniquification
mips: dts: econet: fix EN751221 core type
MIPS: Malta: Fix !EVA SOC-it PCI MMIO
|
|
Commits
28be1b454c2b ("x86/boot: Remove unused copy_*_gs() functions")
34d2819f2078 ("x86, mtrr: Remove unused mtrr/state.c")
removed the functions but left the prototypes. Remove them.
[ bp: Merge into a single patch. ]
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://patch.msgid.link/20251120121037.1479334-1-yuehaibing@huawei.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fix from Eric Biggers:
"Fix another KMSAN warning that made it in while KMSAN wasn't working
reliably"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: tests: Fix KMSAN warning in test_sha256_finup_2x()
|
|
Pull xfs fix from Carlos Maiolino:
"A single out-of-bounds fix, nothing special"
* tag 'xfs-fixes-6.18-rc7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix out of bounds memory read error in symlink repair
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One target driver fix and one scsi-generic one. The latter is 10 lines
because the problem lock has to be dropped and re-taken around the
call causing the sleep in atomic"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: Do not sleep in atomic context
scsi: target: tcm_loop: Fix segfault in tcm_loop_tpg_address_show()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- INPUT_PROP_HAPTIC_TOUCHPAD definition added early in 6.18 cycle has
been renamed to INPUT_PROP_PRESSUREPAD to better reflect the kind of
devices it is supposed to be set for
- a new ID for a touchscreen found in Ayaneo Flip DS in Goodix driver
- Goodix driver no longer tries to set reset pin as "input" as it
causes issues when there is no pull up resistor installed on the
board
- fixes for cros_ec_keyb, imx_sc_key, and pegasus-notetaker drivers to
deal with potential out-of-bounds access and memory corruption issues
* tag 'input-for-v6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: rename INPUT_PROP_HAPTIC_TOUCHPAD to INPUT_PROP_PRESSUREPAD
Input: cros_ec_keyb - fix an invalid memory access
Input: imx_sc_key - fix memory corruption on unload
Input: pegasus-notetaker - fix potential out-of-bounds access
Input: goodix - remove setting of RST pin to input
Input: goodix - add support for ACPI ID GDIX1003
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
- Correct the MIPS RISC-V/JEDEC vendor ID
- Fix the system shutdown behavior in the legacy case where
CONFIG_RISCV_SBI_V01 is set, but the firmware implementation
doesn't support the older v0.1 system shutdown method
- Align some tools/ macro definitions with the corresponding
kernel headers
* tag 'riscv-for-linus-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
tools: riscv: Fixed misalignment of CSR related definitions
riscv: sbi: Prefer SRST shutdown over legacy
riscv: Update MIPS vendor id to 0x127
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fixes from Paul Moore:
"Three SELinux patches for v6.18 to fix issues around accessing the
per-task decision cache that we introduced in v6.16 to help reduce
SELinux overhead on path walks. The problem was that despite the cache
being located in the SELinux "task_security_struct", the parent struct
wasn't actually tied to the task, it was tied to a cred.
Historically SELinux did locate the task_security_struct in the
task_struct's security blob, but it was later relocated to the cred
struct when the cred work happened, as it made the most sense at the
time.
Unfortunately we never did the task_security_struct to
cred_security_struct rename work (avoid code churn maybe? who knows)
because it didn't really matter at the time. However, it suddenly
became a problem when we added a per-task cache to a per-cred object
and didn't notice because of the old, no-longer-correct struct naming.
Thanks to KCSAN for flagging this, as the silly humans running things
forgot that the task_security_struct was a big lie.
This contains three patches, only one of which actually fixes the
problem described above and moves the SELinux decision cache from the
per-cred struct to a newly (re)created per-task struct.
The other two patches, which form the bulk of the diffstat, take care
of the associated renaming tasks so we can hopefully avoid making the
same stupid mistake in the future.
For the record, I did contemplate sending just a fix for the cache,
leaving the renaming patches for the upcoming merge window, but the
type/variable naming ended up being pretty awful and would have made
v6.18 an outlier stuck between the "old" names and the "new" names in
v6.19. The renaming patches are also fairly mechanical/trivial and
shouldn't pose much risk despite their size.
TLDR; naming things may be hard, but if you mess it up bad things
happen"
* tag 'selinux-pr-20251121' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: rename the cred_security_struct variables to "crsec"
selinux: move avdcache to per-task security struct
selinux: rename task_security_struct to cred_security_struct
|
|
Current code retrieving platform devices MSI devID in the GIC ITS MSI
parent helpers suffers from some minor issues:
- It leaks a struct device_node reference
- It is duplicated between GICv3 and GICv5 for no good reason
- It does not use the OF phandle iterator code that simplifies
the msi-parent property parsing
Consolidate GIC v3 and v5 deviceID retrieval in a function that addresses
the full set of issues in one go by merging GIC v3 and v5 code and
converting the msi-parent parsing loop to the more modern OF phandle
iterator API, fixing the struct device_node reference leak in the process.
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://patch.msgid.link/20251021124103.198419-6-lpieralisi@kernel.org
|
|
The functionality implemented in the iproc driver in order to detect an
OF MSI controller node is now fully implemented in of_msi_xlate().
Replace the current msi-map/msi-parent parsing code with of_msi_xlate().
Since of_msi_xlate() is also a deviceID mapping API, pass in a fictitious
0 as deviceID - the driver only requires detecting the OF MSI controller
node not the deviceID mapping per-se (of_msi_xlate() return value is
ignored for the same reason).
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251021124103.198419-5-lpieralisi@kernel.org
|
|
Pick up OF changes to resolve dependencies
|
|
The "shareable_bits" and "bit_usage" resctrl files associated with cache
resources give insight into how instances of a cache is used.
Update the annotated capacity bitmasks displayed by "bit_usage" to include the
cache portions allocated for I/O via the "io_alloc" feature. "shareable_bits"
is a global bitmask of shareable cache with I/O and can thus not present the
per-domain I/O allocations possible with the "io_alloc" feature. Revise the
"shareable_bits" documentation to direct users to "bit_usage" for accurate
cache usage information.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://patch.msgid.link/e02a0d424129fd7f3e45822a559b1c614ae4652a.1762995456.git.babu.moger@amd.com
|
|
The io_alloc feature in resctrl enables system software to configure the
portion of the cache allocated for I/O traffic. When supported, the
io_alloc_cbm file in resctrl provides access to capacity bitmasks (CBMs)
allocated for I/O devices.
Enable users to modify io_alloc CBMs by writing to the io_alloc_cbm resctrl
file when the io_alloc feature is enabled.
Mirror the CBMs between CDP_CODE and CDP_DATA when CDP is enabled to present
consistent I/O allocation information to user space.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://patch.msgid.link/67609641b03ccfba18a8ee0bf9dbd1f3dcbecda3.1762995456.git.babu.moger@amd.com
|
|
A report from Oleg Smirnov indicates that the unusual_devs quirks
entry for the Novatek camera does not need to override the subclass
and protocol parameters:
[3266355.209532] usb 1-3: new high-speed USB device number 10 using xhci_hcd
[3266355.333031] usb 1-3: New USB device found, idVendor=0603, idProduct=8611, bcdDevice= 1.00
[3266355.333040] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3266355.333043] usb 1-3: Product: YICARCAM
[3266355.333045] usb 1-3: Manufacturer: XIAO-YI
[3266355.333047] usb 1-3: SerialNumber: 966110000000100
[3266355.338621] usb-storage 1-3:1.0: USB Mass Storage device detected
[3266355.338817] usb-storage 1-3:1.0: Quirks match for vid 0603 pid 8611: 4000
[3266355.338821] usb-storage 1-3:1.0: This device (0603,8611,0100 S 06 P 50) has unneeded SubClass and Protocol entries in unusual_devs.h (kernel 6.16.10-arch1-1)
Please send a copy of this message to
<linux-usb@vger.kernel.org> and <usb-storage@lists.one-eyed-alien.net>
The overrides are harmless but they do provoke the driver into logging
this annoying message. Update the entry to remove the unneeded entries.
Reported-by: stealth <oleg.smirnov.1988@gmail.com>
Closes: https://lore.kernel.org/CAKxjRRxhC0s19iEWoN=pEMqXJ_z8w_moC0GCXSqSKCcOddnWjQ@mail.gmail.com/
Fixes: 6ca8af3c8fb5 ("USB: storage: Add unusual-devs entry for Novatek NTK96550-based camera")
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/b440f177-f0b8-4d5a-8f7b-10855d4424ee@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit a52ddb98a674 ("memory: tegra186-emc: Simplify and handle deferred
probe with dev_err_probe()") accidently dropped a call to 'put_bpmp' to
release a handle to the BPMP when getting the EMC clock fails. Fix this
by restoring the 'goto put_bpmp' if devm_clk_get() fails.
Fixes: a52ddb98a674 ("memory: tegra186-emc: Simplify and handle deferred probe with dev_err_probe()")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20251106190550.1776974-1-jonathanh@nvidia.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
parse_cbm() requires resource group mode and CLOSID to validate the capacity
bitmask (CBM). It is passed via struct rdtgroup in struct rdt_parse_data.
The io_alloc feature also uses CBMs to indicate which portions of cache are
allocated for I/O traffic. The CBMs are provided by user space and need to be
validated the same as CBMs provided for general (CPU) cache allocation.
parse_cbm() cannot be used as-is since io_alloc does not have rdtgroup context.
Pass the resource group mode and CLOSID directly to parse_cbm() via struct
rdt_parse_data, instead of through the rdtgroup struct, to facilitate calling
parse_cbm() to verify the CBM of the io_alloc feature.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://patch.msgid.link/f8ec6ab5cf594d906a3fe75f56793d5fbd63f38f.1762995456.git.babu.moger@amd.com
|
|
If the linker emits warnings these should abort the build.
Otherwise they will be swallowed by run-tests.sh and not shown.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
|
|
LLVM 21 switched to -mcmodel=medium for LoongArch64 compilations.
This code model uses R_LARCH_ECALL36 relocations which might not be
supported by GNU ld which to nolibc testsuite uses by default.
ld will not resolve the relocation and all function calls will end up
as busy loops.
Use lld instead.
We can not switch to lld for all LLVM builds, as it does not support all
necessary architectures.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
|
|
Introduce the "io_alloc_cbm" resctrl file to display the capacity bitmasks
(CBMs) that represent the portions of each cache instance allocated
for I/O traffic on a cache resource that supports the "io_alloc" feature.
io_alloc_cbm resides in the info directory of a cache resource, for example,
/sys/fs/resctrl/info/L3/. Since the resource name is part of the path, it
is not necessary to display the resource name as done in the schemata file.
When CDP is enabled, io_alloc routes traffic using the highest CLOSID
associated with the CDP_CODE resource and that CLOSID becomes unusable for
the CDP_DATA resource. The highest CLOSID of CDP_CODE and CDP_DATA resources
will be kept in sync to ensure consistent user interface. In preparation for
this, access the CBMs for I/O traffic through highest CLOSID of either
CDP_CODE or CDP_DATA resource.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://patch.msgid.link/55a3ff66a70e7ce8239f022e62b334e9d64af604.1762995456.git.babu.moger@amd.com
|
|
Failing to allocate the affinity mask of an interrupt descriptor fails the
whole descriptor initialization. It is then guaranteed that the cpumask is
always available whenever the related interrupt objects are alive, such as
the kthread handler.
Therefore remove the superfluous check since it is merely a historical
leftover. Get rid also of the comments above it that are obsolete and
useless.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://patch.msgid.link/20251121143500.42111-4-frederic@kernel.org
|
|
When a cpuset isolated partition is created / updated or destroyed, the
interrupt threads are affined blindly to all the non-isolated CPUs. This
happens without taking into account the interrupt threads initial affinity
that becomes ignored.
For example in a system with 8 CPUs, if an interrupt and its kthread are
initially affine to CPU 5, creating an isolated partition with only CPU 2
inside will eventually end up affining the interrupt kthread to all CPUs
but CPU 2 (that is CPUs 0,1,3-7), losing the kthread preference for CPU 5.
Besides the blind re-affining, this doesn't take care of the actual low
level interrupt which isn't migrated. As of today the only way to isolate
non managed interrupts, along with their kthreads, is to overwrite their
affinity separately, for example through /proc/irq/
To avoid doing that manually, future development should focus on updating
the interrupt's affinity whenever cpuset isolated partitions are updated.
In the meantime, cpuset shouldn't fiddle with interrupt threads directly.
To prevent from that, set the PF_NO_SETAFFINITY flag to them.
This is done through kthread_bind_mask() by affining them initially to all
possible CPUs as at that point the interrupt is not started up which means
the affinity of the hard interrupt is not known. The thread will adjust
that once it reaches the handler, which is guaranteed to happen after the
initial affinity of the hard interrupt is established.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://patch.msgid.link/20251121143500.42111-3-frederic@kernel.org
|
|
During initialization, the interrupt thread is created before the interrupt
is enabled. The interrupt enablement happens before the actual kthread wake
up point. Once the interrupt is enabled the hardware can raise an interrupt
and once setup_irq() drops the descriptor lock a interrupt wake-up can
happen.
Even when such an interrupt can be considered premature, this is not a
problem in general because at the point where the descriptor lock is
dropped and the wakeup can happen, the data which is used by the thread is
fully initialized.
Though from the perspective of least surprise, the initial wakeup really
should be performed by the setup code and not randomly by a premature
interrupt.
Prevent this by performing a wake-up only if the target is in state
TASK_INTERRUPTIBLE, which the thread uses in wait_for_interrupt().
If the thread is still in state TASK_UNINTERRUPTIBLE, the wake-up is not
lost because after the setup code completed the initial wake-up the thread
will observe the IRQTF_RUNTHREAD and proceed with the handling.
[ tglx: Simplified the changes and extended the changelog. ]
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://patch.msgid.link/20251121143500.42111-2-frederic@kernel.org
|
|
Puranjay Mohan says:
====================
bpf: Nested rcu critical sections
v1: https://lore.kernel.org/bpf/20250916113622.19540-1-puranjay@kernel.org/
Changes in v1->v2:
- Move the addition of new tests to a separate patch (Alexei)
- Avoid incrementing active_rcu_locks at two places (Eduard)
Support nested rcu critical sections by making the boolean flag
active_rcu_lock a counter and use it to manage rcu critical section
state. bpf_rcu_read_lock() increments this counter and
bpf_rcu_read_unlock() decrements it, MEM_RCU -> PTR_UNTRUSTED transition
happens when active_rcu_locks drops to 0.
====================
Link: https://patch.msgid.link/20251117200411.25563-1-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
As verifier now supports nested rcu critical sections, add new test
cases to make sure unbalanced usage of rcu_read_lock()/unlock() is
rejected.
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251117200411.25563-3-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently, nested rcu critical sections are rejected by the verifier and
rcu_lock state is managed by a boolean variable. Add support for nested
rcu critical sections by make active_rcu_locks a counter similar to
active_preempt_locks. bpf_rcu_read_lock() increments this counter and
bpf_rcu_read_unlock() decrements it, MEM_RCU -> PTR_UNTRUSTED transition
happens when active_rcu_locks drops to 0.
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251117200411.25563-2-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_sock: Prevent race in socket write iter and sock bind
- hci_core: Fix triggering cmd_timer for HCI_OP_NOP
- hci_core: lookup hci_conn on RX path on protocol side
- SMP: Fix not generating mackey and ltk when repairing
- btusb: mediatek: Fix kernel crash when releasing mtk iso interface
- btusb: mediatek: Avoid btusb_mtk_claim_iso_intf() NULL deref
* tag 'for-net-2025-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: SMP: Fix not generating mackey and ltk when repairing
Bluetooth: btusb: mediatek: Avoid btusb_mtk_claim_iso_intf() NULL deref
Bluetooth: hci_core: lookup hci_conn on RX path on protocol side
Bluetooth: hci_sock: Prevent race in socket write iter and sock bind
Bluetooth: hci_core: Fix triggering cmd_timer for HCI_OP_NOP
Bluetooth: btusb: mediatek: Fix kernel crash when releasing mtk iso interface
====================
Link: https://patch.msgid.link/20251121145332.177015-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
net: stmmac: qcon-ethqos: "rgmii" accessor cleanups
This series cleans up the "rgmii" accessors in qcom-ethqos.
readl() and writel() return and take a u32 for the value. Rather than
implicitly casting this to an int, keep it as a u32.
Add set/clear functions to reduce the code and make it easier to read.
Finally, convert the open-coded poll loops to use the iopoll helpers.
Note that patch 1 has a checkpatch warning concerning "volatile" -
I'm changing the type here, and the "volatile" is removed in patch 3.
I do not feel it is appropriate to remove it in patch 1.
====================
Link: https://patch.msgid.link/aR76i0HjXitfl7xk@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use read_poll_timeout_atomic() to poll the rgmii registers rather than
open-coding the polling.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vM2n1-0000000FRTu-0js9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver has a lot of bit manipulation of the RGMII registers. Add
a pair of helpers to set bits and clear bits, converting the various
calls to rgmii_updatel() as appropriate.
Most of the change was done via this sed script:
/rgmii_updatel/ {
N
/,$/N
/mask, / ! {
s|rgmii_updatel\(([^,]*,\s+([^,]*),\s+)\2,\s+|rgmii_setmask(\1|
s|rgmii_updatel\(([^,]*,\s+([^,]*),\s+)0,\s+|rgmii_clrmask(\1|
s|^\s+$||
}
}
and then formatting tweaked where necessary.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vM2mw-0000000FRTo-0End@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
readl() returns a u32, and writel() takes a "u32" for the value. These
are used in rgmii_readl()() and rgmii_writel(), but the value and
return are "int". As these are 32-bit register values which are not
signed, use "u32".
These changes do not cause generated code changes.
Update rgmii_updatel() to use u32 for mask and val. Changing "mask"
to "u32" also does not cause generated code changes. However, changing
"val" causes the generated assembly to be re-ordered for aarch64.
Update the temporary variables used with the rgmii functions to use
u32.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vM2mq-0000000FRTi-3y5F@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As the interface mode doesn't need to be updated on PHYs connected with
USXGMII and integrated PHYs, gpy_update_interface() should just return 0
in these cases rather than -EINVAL which has wrongly been introduced by
commit 7a495dde27ebc ("net: phy: mxl-gpy: Change gpy_update_interface()
function return type"), as this breaks support for those PHYs.
Fixes: 7a495dde27ebc ("net: phy: mxl-gpy: Change gpy_update_interface() function return type")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/f744f721a1fcc5e2e936428c62ff2c7d94d2a293.1763648168.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function was used in t7xx_hif_cldma.c only. Make it static
as it should be.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Loic Poulain <loic.poulain@qualcomm.com>
Link: https://patch.msgid.link/20251120115208.345578-1-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 0f8d42bf128d349ad490e87d5574d211245e40f1, with the
memcpy_sglist() part dropped.
Now that memcpy_sglist() no longer uses the skcipher_walk code, the
skcipher_walk code can be moved back to where it belongs.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The original implementation of memcpy_sglist() was broken because it
didn't handle scatterlists that describe exactly the same memory, which
is a case that many callers rely on. The current implementation is
broken too because it calls the skcipher_walk functions which can fail.
It ignores any errors from those functions.
Fix it by replacing it with a new implementation written from scratch.
It always succeeds. It's also a bit faster, since it avoids the
overhead of skcipher_walk. skcipher_walk includes a lot of
functionality (such as alignmask handling) that's irrelevant here.
Reported-by: Colin Ian King <coking@nvidia.com>
Closes: https://lore.kernel.org/r/20251114122620.111623-1-coking@nvidia.com
Fixes: 131bdceca1f0 ("crypto: scatterwalk - Add memcpy_sglist")
Fixes: 0f8d42bf128d ("crypto: scatterwalk - Move skcipher walk and use it for memcpy_sglist")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
