kernel.git/sound/soc/davinci, branch linux-4.3.y

ASoC: davinci-mcasp: Fix XDATA check in mcasp_start_tx

2016-01-31T19:25:48Z

commit e2a0c9fa80227be5ee017b5476638829dd41cb39 upstream. The condition for checking for XDAT being cleared was not correct. Fixes: 36bcecd0a73eb ("ASoC: davinci-mcasp: Correct TX start sequence") Signed-off-by: Peter Ujfalusi Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman

ASoC: davinci-mcasp: Fix devm_kasprintf format string

2015-09-18T15:22:07Z

The '\n' at the end of the format string is not needed. It adds an extra line break when doing cat /proc/interrupts Signed-off-by: Peter Ujfalusi Signed-off-by: Mark Brown

ASoC: davinci-mcasp: Set .symmetric_rates = 1 in snd_soc_dai_driver

2015-09-14T18:40:08Z

The TX and RX direction share the same bit clock and frame sync, so the samplerate must be the same to both directions. Signed-off-by: Jyri Sarha Acked-by: Peter Ujfalusi Signed-off-by: Mark Brown

ASoC: davinci-mcasp: Revise the FIFO threshold calculation

2015-09-14T16:29:41Z

The FIFO threshold for McASP should be <=[tx/rx]numevt so the initial value for the refining should meet this requirement as well. Signed-off-by: Peter Ujfalusi Signed-off-by: Mark Brown

Merge remote-tracking branches 'asoc/topic/davinci', 'asoc/topic/davinci-vcif', 'asoc/topic/doc' and 'asoc/topic/dpcm' into asoc-next

2015-08-30T14:53:39Z

ASoC: davinci: Convert to use devm_ioremap_resource

2015-08-25T09:27:04Z

Use devm_ioremap_resource() instead of open code. Signed-off-by: Axel Lin Acked-by: Peter Ujfalusi Signed-off-by: Mark Brown

ASoC: davinci-vcif: Use devm_snd_soc_register_component

2015-08-17T20:48:28Z

Use resource managed function devm_snd_soc_register_component for component registration instead of snd_soc_register_component. Also, remove davinci_vcif_remove as it is now redundant. Signed-off-by: Vaishali Thakkar Acked-by: Peter Ujfalusi Signed-off-by: Mark Brown

Merge remote-tracking branch 'asoc/topic/davinci' into asoc-next

2015-06-22T09:24:30Z

ASoC: davinci-mcasp: Choose PCM driver based on configured DMA controller

2015-06-09T18:00:52Z

Find the configured DMA controller by asking for a DMA channel in the probe phase and releasing it right after. The controller device can be found via the dma_chan struct and the controller is recognized from the compatible property of its device node. The patch assumes EDMA if there is no device node. Signed-off-by: Jyri Sarha Acked-by: Peter Ujfalusi Signed-off-by: Mark Brown

ASoC: davinci-mcasp: Logic low for inactive output slots

2015-06-08T17:51:26Z

The default state when serializers are in inactive slots is Hi-Z. In some cases, there are no additional components driving the data lines to a safe state so they might have noise. While in inactive slots, the McASP AXR pins configured as outputs can be driven low through the serializer pin drive mode setting (DISMOD) to prevent such noise. Signed-off-by: Misael Lopez Cruz Signed-off-by: Peter Ujfalusi Signed-off-by: Mark Brown