kernel.git/sound/soc/bcm, branch linux-4.15.y

Merge remote-tracking branches 'asoc/topic/cygnus', 'asoc/topic/da7213', 'asoc/topic/davinci' and 'asoc/topic/doc' into asoc-next

2017-11-10T21:31:10Z

ASoC: bcm2835: Support left/right justified and DSP modes

2017-11-10T21:26:07Z

DSP modes and left/right justified modes can be supported on bcm2835 by configuring the frame sync polarity and frame sync length registers and by adjusting the channel data position registers. Clock and frame sync polarity handling in hw_params has been refactored to make the interaction between logical rising/falling edge frame start and physical configuration (changed by normal/inverted polarity modes) clearer. Modes where the first active data bit is transmitted immediately after frame start (eg DSP mode B with slot 0 active) only work reliable if bcm2835 is configured as frame master. In frame slave mode channel swap (or shift, this isn't quite clear yet) can occur. Currently the driver only warns if an unstable configuration is detected but doensn't prevent using them. Signed-off-by: Matthias Reichl Signed-off-by: Mark Brown

ASoC: bcm2835: Enforce full symmetry

2017-11-10T21:26:03Z

bcm2835's configuration registers can't be changed when a stream is running, which means asymmetric configurations aren't supported. Channel and rate symmetry are already enforced by constraints but samplebits had been missed. As hw_params doesn't check for symmetry constraints by itself and just returns success if a stream is running this led to situations where asymmetric configurations were seeming to succeed but of course didn't work because the hardware wasn't configured at all. Fix this by adding the missing samplerate symmetry constraint. Signed-off-by: Matthias Reichl Signed-off-by: Mark Brown

ASoC: bcm2835: Support additional samplerates up to 384kHz

2017-11-10T21:24:34Z

Sample rates are only restricted by the capabilities of the clock driver, so use SNDRV_PCM_RATE_CONTINUOUS instead of SNDRV_PCM_RATE_8000_192000. Tests (eg with pcm5122) have shown that bcm2835 works fine in 384kHz/32bit stereo mode, so change the maximum allowed rate from 192kHz to 384kHz. Signed-off-by: Matthias Reichl Reviewed-by: Eric Anholt Signed-off-by: Mark Brown

ASoC: bcm2835: Add support for TDM modes

2017-11-10T21:24:30Z

bcm2835 supports arbitrary positioning of channel data within a frame and thus is capable of supporting TDM modes. Since the driver is limited to 2-channel operations only TDM setups with exactly 2 active slots are supported. Logical TDM slot numbering follows the usual convention: For I2S-like modes, with a 50% duty-cycle frame clock, slots 0, 2, ... are transmitted in the first half of a frame, slots 1, 3, ... are transmitted in the second half. For DSP modes slot numbering is ascending: 0, 1, 2, 3, ... Channel position calculation has been refactored to use TDM info and moved out of hw_params. set_tdm_slot, set_bclk_ratio and hw_params now check more strictly if the configuration is valid. Illegal configurations like odd number of slots in I2S mode, data lengths exceeding slot width or frame sizes larger than the hardware limit of 1024 are rejected. Also hw_params now properly checks for errors from clk_set_rate. Allowed PCM formats are already guarded by stream constraints, thus the formats check in hw_params has been removed and data_length is now retrieved via params_width(). Also standard functions like snd_soc_params_to_bclk are now being used instead of manual calculations to make the code more readable. Special care has been taken to ensure that set_bclk_ratio works as before. The bclk ratio is mapped to a 2-channel TDM config with a slot width of half the ratio. In order to support odd ratios, which can't be expressed via a TDM config, the ratio (frame length) is stored and used by hw_params. Signed-off-by: Matthias Reichl Signed-off-by: Mark Brown

ASoC: cygnus: Remove unnecessary active_slots check

2017-10-09T08:41:05Z

Variable active_slots is unsigned so checking whether it is less than zero is not necessary. Signed-off-by: Christos Gkekas Signed-off-by: Mark Brown

ASoC: cygnus: Remove support for 8 bit audio and for mono

2017-10-04T10:59:37Z

These modes of operation were not working properly and it is unclear if the hardware could fully support these modes properly. There is little to be gained by enabling these modes, therefore, we will just remove support. Signed-off-by: Lori Hikichi Signed-off-by: Mark Brown

ASoC: cygnus: Remove set_fmt from SPDIF dai ops

2017-10-04T10:59:24Z

The SPDIF port cannot modify its format so a set_fmt function is not needed. Previously, we used a generic set_fmt for all ports and returned an error code for the SPDIF port. It is cleaner to not populate the set_fmt field. Signed-off-by: Lori Hikichi Signed-off-by: Mark Brown

ASoC: cygnus: Add EXPORT_SYMBOL for helper function

2017-10-04T10:59:16Z

The helper function cygnus_ssp_set_custom_fsync_width() is intended to be called from an ASoC machine driver, need to export symbol if using modules. Signed-off-by: Lori Hikichi Signed-off-by: Mark Brown

Merge remote-tracking branches 'asoc/topic/cs43130', 'asoc/topic/cs53l30', 'asoc/topic/cygnus' and 'asoc/topic/davinci' into asoc-next

2017-09-01T11:12:32Z