kernel.git/net/rxrpc/call_object.c, branch linux-5.8.y

rxrpc: Fix loss of RTT samples due to interposed ACK

2020-09-09T17:14:13Z

[ Upstream commit 4700c4d80b7bb171f6996016ef121e1508860b42 ] The Rx protocol has a mechanism to help generate RTT samples that works by a client transmitting a REQUESTED-type ACK when it receives a DATA packet that has the REQUEST_ACK flag set. The peer, however, may interpose other ACKs before transmitting the REQUESTED-ACK, as can be seen in the following trace excerpt: rxrpc_tx_data: c=00000044 DATA d0b5ece8:00000001 00000001 q=00000001 fl=07 rxrpc_rx_ack: c=00000044 00000001 PNG r=00000000 f=00000002 p=00000000 n=0 rxrpc_rx_ack: c=00000044 00000002 REQ r=00000001 f=00000002 p=00000001 n=0 ... DATA packet 1 (q=xx) has REQUEST_ACK set (bit 1 of fl=xx). The incoming ping (labelled PNG) hard-acks the request DATA packet (f=xx exceeds the sequence number of the DATA packet), causing it to be discarded from the Tx ring. The ACK that was requested (labelled REQ, r=xx references the serial of the DATA packet) comes after the ping, but the sk_buff holding the timestamp has gone and the RTT sample is lost. This is particularly noticeable on RPC calls used to probe the service offered by the peer. A lot of peers end up with an unknown RTT because we only ever sent a single RPC. This confuses the server rotation algorithm. Fix this by caching the information about the outgoing packet in RTT calculations in the rxrpc_call struct rather than looking in the Tx ring. A four-deep buffer is maintained and both REQUEST_ACK-flagged DATA and PING-ACK transmissions are recorded in there. When the appropriate response ACK is received, the buffer is checked for a match and, if found, an RTT sample is recorded. If a received ACK refers to a packet with a later serial number than an entry in the cache, that entry is presumed lost and the entry is made available to record a new transmission. ACKs types other than REQUESTED-type and PING-type cause any matching sample to be cancelled as they don't necessarily represent a useful measurement. If there's no space in the buffer on ping/data transmission, the sample base is discarded. Fixes: 50235c4b5a2f ("rxrpc: Obtain RTT data by requesting ACKs on DATA packets") Signed-off-by: David Howells Signed-off-by: Sasha Levin

rxrpc: Fix race between recvmsg and sendmsg on immediate call failure

2020-07-30T23:50:20Z

There's a race between rxrpc_sendmsg setting up a call, but then failing to send anything on it due to an error, and recvmsg() seeing the call completion occur and trying to return the state to the user. An assertion fails in rxrpc_recvmsg() because the call has already been released from the socket and is about to be released again as recvmsg deals with it. (The recvmsg_q queue on the socket holds a ref, so there's no problem with use-after-free.) We also have to be careful not to end up reporting an error twice, in such a way that both returns indicate to userspace that the user ID supplied with the call is no longer in use - which could cause the client to malfunction if it recycles the user ID fast enough. Fix this by the following means: (1) When sendmsg() creates a call after the point that the call has been successfully added to the socket, don't return any errors through sendmsg(), but rather complete the call and let recvmsg() retrieve them. Make sendmsg() return 0 at this point. Further calls to sendmsg() for that call will fail with ESHUTDOWN. Note that at this point, we haven't send any packets yet, so the server doesn't yet know about the call. (2) If sendmsg() returns an error when it was expected to create a new call, it means that the user ID wasn't used. (3) Mark the call disconnected before marking it completed to prevent an oops in rxrpc_release_call(). (4) recvmsg() will then retrieve the error and set MSG_EOR to indicate that the user ID is no longer known by the kernel. An oops like the following is produced: kernel BUG at net/rxrpc/recvmsg.c:605! ... RIP: 0010:rxrpc_recvmsg+0x256/0x5ae ... Call Trace: ? __init_waitqueue_head+0x2f/0x2f ____sys_recvmsg+0x8a/0x148 ? import_iovec+0x69/0x9c ? copy_msghdr_from_user+0x5c/0x86 ___sys_recvmsg+0x72/0xaa ? __fget_files+0x22/0x57 ? __fget_light+0x46/0x51 ? fdget+0x9/0x1b do_recvmmsg+0x15e/0x232 ? _raw_spin_unlock+0xa/0xb ? vtime_delta+0xf/0x25 __x64_sys_recvmmsg+0x2c/0x2f do_syscall_64+0x4c/0x78 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 357f5ef64628 ("rxrpc: Call rxrpc_release_call() on error in rxrpc_new_client_call()") Reported-by: syzbot+b54969381df354936d96@syzkaller.appspotmail.com Signed-off-by: David Howells Reviewed-by: Marc Dionne Signed-off-by: David S. Miller

rxrpc: Fix call interruptibility handling

2020-03-13T23:04:30Z

Fix the interruptibility of kernel-initiated client calls so that they're either only interruptible when they're waiting for a call slot to come available or they're not interruptible at all. Either way, they're not interruptible during transmission. This should help prevent StoreData calls from being interrupted when writeback is in progress. It doesn't, however, handle interruption during the receive phase. Userspace-initiated calls are still interruptable. After the signal has been handled, sendmsg() will return the amount of data copied out of the buffer and userspace can perform another sendmsg() call to continue transmission. Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Signed-off-by: David Howells

rxrpc: Fix call RCU cleanup using non-bh-safe locks

2020-02-07T10:20:57Z

rxrpc_rcu_destroy_call(), which is called as an RCU callback to clean up a put call, calls rxrpc_put_connection() which, deep in its bowels, takes a number of spinlocks in a non-BH-safe way, including rxrpc_conn_id_lock and local->client_conns_lock. RCU callbacks, however, are normally called from softirq context, which can cause lockdep to notice the locking inconsistency. To get lockdep to detect this, it's necessary to have the connection cleaned up on the put at the end of the last of its calls, though normally the clean up is deferred. This can be induced, however, by starting a call on an AF_RXRPC socket and then closing the socket without reading the reply. Fix this by having rxrpc_rcu_destroy_call() punt the destruction to a workqueue if in softirq-mode and defer the destruction to process context. Note that another way to fix this could be to add a bunch of bh-disable annotations to the spinlocks concerned - and there might be more than just those two - but that means spending more time with BHs disabled. Note also that some of these places were covered by bh-disable spinlocks belonging to the rxrpc_transport object, but these got removed without the _bh annotation being retained on the next lock in. Fixes: 999b69f89241 ("rxrpc: Kill the client connection bundle concept") Reported-by: syzbot+d82f3ac8d87e7ccbb2c9@syzkaller.appspotmail.com Reported-by: syzbot+3f1fd6b8cbf8702d134e@syzkaller.appspotmail.com Signed-off-by: David Howells cc: Hillf Danton Signed-off-by: David S. Miller

rxrpc: Fix NULL pointer deref due to call->conn being cleared on disconnect

2020-02-03T10:25:30Z

When a call is disconnected, the connection pointer from the call is cleared to make sure it isn't used again and to prevent further attempted transmission for the call. Unfortunately, there might be a daemon trying to use it at the same time to transmit a packet. Fix this by keeping call->conn set, but setting a flag on the call to indicate disconnection instead. Remove also the bits in the transmission functions where the conn pointer is checked and a ref taken under spinlock as this is now redundant. Fixes: 8d94aa381dab ("rxrpc: Calls shouldn't hold socket refs") Signed-off-by: David Howells

rxrpc: Fix call crypto state cleanup

2019-10-07T10:05:05Z

Fix the cleanup of the crypto state on a call after the call has been disconnected. As the call has been disconnected, its connection ref has been discarded and so we can't go through that to get to the security ops table. Fix this by caching the security ops pointer in the rxrpc_call struct and using that when freeing the call security state. Also use this in other places we're dealing with call-specific security. The symptoms look like: BUG: KASAN: use-after-free in rxrpc_release_call+0xb2d/0xb60 net/rxrpc/call_object.c:481 Read of size 8 at addr ffff888062ffeb50 by task syz-executor.5/4764 Fixes: 1db88c534371 ("rxrpc: Fix -Wframe-larger-than= warnings from on-stack crypto") Reported-by: syzbot+eed305768ece6682bb7f@syzkaller.appspotmail.com Signed-off-by: David Howells

rxrpc: Fix trace-after-put looking at the put call record

2019-10-07T10:05:05Z

rxrpc_put_call() calls trace_rxrpc_call() after it has done the decrement of the refcount - which looks at the debug_id in the call record. But unless the refcount was reduced to zero, we no longer have the right to look in the record and, indeed, it may be deleted by some other thread. Fix this by getting the debug_id out before decrementing the refcount and then passing that into the tracepoint. Fixes: e34d4234b0b7 ("rxrpc: Trace rxrpc_call usage") Signed-off-by: David Howells

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2019-09-02T18:20:17Z

r8152 conflicts are the NAPI fixes in 'net' overlapping with some tasklet stuff in net-next Signed-off-by: David S. Miller

rxrpc: Use the tx-phase skb flag to simplify tracing

2019-08-27T09:04:18Z

Use the previously-added transmit-phase skbuff private flag to simplify the socket buffer tracing a bit. Which phase the skbuff comes from can now be divined from the skb rather than having to be guessed from the call state. We can also reduce the number of rxrpc_skb_trace values by eliminating the difference between Tx and Rx in the symbols. Signed-off-by: David Howells

rxrpc: Abstract out rxtx ring cleanup

2019-08-27T09:03:26Z

Abstract out rxtx ring cleanup into its own function from its two callers. This makes it easier to apply the same changes to both. Signed-off-by: David Howells