kernel.git/net/dsa/dsa2.c, branch linux-5.12.y

net: dsa: Fix type was not set for devlink port

2021-03-29T20:49:04Z

If PHY is not available on DSA port (described at devicetree but absent or failed to detect) then kernel prints warning after 3700 secs: [ 3707.948771] ------------[ cut here ]------------ [ 3707.948784] Type was not set for devlink port. [ 3707.948894] WARNING: CPU: 1 PID: 17 at net/core/devlink.c:8097 0xc083f9d8 We should unregister the devlink port as a user port and re-register it as an unused port before executing "continue" in case of dsa_port_setup error. Fixes: 86f8b1c01a0a ("net: dsa: Do not make user port errors fatal") Signed-off-by: Maxim Kochetkov Reviewed-by: Vladimir Oltean Signed-off-by: David S. Miller

net: dsa: don't assign an error value to tag_ops

2021-03-23T00:24:42Z

Use a temporary variable to hold the return value from dsa_tag_driver_get() instead of assigning it to dst->tag_ops. Leaving an error value in dst->tag_ops can result in deferencing an invalid pointer when a deferred switch configuration happens later. Fixes: 357f203bb3b5 ("net: dsa: keep a copy of the tagging protocol in the DSA switch tree") Signed-off-by: George McCollister Reviewed-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2021-02-10T21:30:12Z

net: dsa: call teardown method on probe failure

2021-02-05T04:22:00Z

Since teardown is supposed to undo the effects of the setup method, it should be called in the error path for dsa_switch_setup, not just in dsa_switch_teardown. Fixes: 5e3f847a02aa ("net: dsa: Add teardown callback for drivers") Signed-off-by: Vladimir Oltean Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Link: https://lore.kernel.org/r/20210204163351.2929670-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski

net: dsa: allow changing the tag protocol via the "tagging" device attribute

2021-01-30T05:24:39Z

Currently DSA exposes the following sysfs: $ cat /sys/class/net/eno2/dsa/tagging ocelot which is a read-only device attribute, introduced in the kernel as commit 98cdb4807123 ("net: dsa: Expose tagging protocol to user-space"), and used by libpcap since its commit 993db3800d7d ("Add support for DSA link-layer types"). It would be nice if we could extend this device attribute by making it writable: $ echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging This is useful with DSA switches that can make use of more than one tagging protocol. It may be useful in dsa_loop in the future too, to perform offline testing of various taggers, or for changing between dsa and edsa on Marvell switches, if that is desirable. In terms of implementation, drivers can support this feature by implementing .change_tag_protocol, which should always leave the switch in a consistent state: either with the new protocol if things went well, or with the old one if something failed. Teardown of the old protocol, if necessary, must be handled by the driver. Some things remain as before: - The .get_tag_protocol is currently only called at probe time, to load the initial tagging protocol driver. Nonetheless, new drivers should report the tagging protocol in current use now. - The driver should manage by itself the initial setup of tagging protocol, no later than the .setup() method, as well as destroying resources used by the last tagger in use, no earlier than the .teardown() method. For multi-switch DSA trees, error handling is a bit more complicated, since e.g. the 5th out of 7 switches may fail to change the tag protocol. When that happens, a revert to the original tag protocol is attempted, but that may fail too, leaving the tree in an inconsistent state despite each individual switch implementing .change_tag_protocol transactionally. Since the intersection between drivers that implement .change_tag_protocol and drivers that support D in DSA is currently the empty set, the possibility for this error to happen is ignored for now. Testing: $ insmod mscc_felix.ko [ 79.549784] mscc_felix 0000:00:00.5: Adding to iommu group 14 [ 79.565712] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517 $ insmod tag_ocelot.ko $ rmmod mscc_felix.ko $ insmod mscc_felix.ko [ 97.261724] libphy: VSC9959 internal MDIO bus: probed [ 97.267363] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 [ 97.274998] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 [ 97.282561] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 [ 97.289700] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 [ 97.599163] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL) [ 97.862034] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL) [ 97.950731] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode [ 97.964278] 8021q: adding VLAN 0 to HW filter on device swp0 [ 98.146161] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL) [ 98.238649] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode [ 98.251845] 8021q: adding VLAN 0 to HW filter on device swp1 [ 98.433916] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL) [ 98.485542] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode [ 98.503584] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 98.527948] device eno2 entered promiscuous mode [ 98.544755] DSA: tree 0 setup $ ping 10.0.0.1 PING 10.0.0.1 (10.0.0.1): 56 data bytes 64 bytes from 10.0.0.1: seq=0 ttl=64 time=2.337 ms 64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.754 ms ^C - 10.0.0.1 ping statistics - 2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 0.754/1.545/2.337 ms $ cat /sys/class/net/eno2/dsa/tagging ocelot $ cat ./test_ocelot_8021q.sh #!/bin/bash ip link set swp0 down ip link set swp1 down ip link set swp2 down ip link set swp3 down ip link set swp5 down ip link set eno2 down echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging ip link set eno2 up ip link set swp0 up ip link set swp1 up ip link set swp2 up ip link set swp3 up ip link set swp5 up $ ./test_ocelot_8021q.sh ./test_ocelot_8021q.sh: line 9: echo: write error: Protocol not available $ rmmod tag_ocelot.ko rmmod: can't unload module 'tag_ocelot': Resource temporarily unavailable $ insmod tag_ocelot_8021q.ko $ ./test_ocelot_8021q.sh $ cat /sys/class/net/eno2/dsa/tagging ocelot-8021q $ rmmod tag_ocelot.ko $ rmmod tag_ocelot_8021q.ko rmmod: can't unload module 'tag_ocelot_8021q': Resource temporarily unavailable $ ping 10.0.0.1 PING 10.0.0.1 (10.0.0.1): 56 data bytes 64 bytes from 10.0.0.1: seq=0 ttl=64 time=0.953 ms 64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.787 ms 64 bytes from 10.0.0.1: seq=2 ttl=64 time=0.771 ms $ rmmod mscc_felix.ko [ 645.544426] mscc_felix 0000:00:00.5: Link is Down [ 645.838608] DSA: tree 0 torn down $ rmmod tag_ocelot_8021q.ko Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: dsa: keep a copy of the tagging protocol in the DSA switch tree

2021-01-30T05:24:31Z

Cascading DSA switches can be done multiple ways. There is the brute force approach / tag stacking, where one upstream switch, located between leaf switches and the host Ethernet controller, will just happily transport the DSA header of those leaf switches as payload. For this kind of setups, DSA works without any special kind of treatment compared to a single switch - they just aren't aware of each other. Then there's the approach where the upstream switch understands the tags it transports from its leaves below, as it doesn't push a tag of its own, but it routes based on the source port & switch id information present in that tag (as opposed to DMAC & VID) and it strips the tag when egressing a front-facing port. Currently only Marvell implements the latter, and Marvell DSA trees contain only Marvell switches. So it is safe to say that DSA trees already have a single tag protocol shared by all switches, and in fact this is what makes the switches able to understand each other. This fact is also implied by the fact that currently, the tagging protocol is reported as part of a sysfs installed on the DSA master and not per port, so it must be the same for all the ports connected to that DSA master regardless of the switch that they belong to. It's time to make this official and enforce it (yes, this also means we won't have any "switch understands tag to some extent but is not able to speak it" hardware oddities that we'll support in the future). This is needed due to the imminent introduction of the dsa_switch_ops:: change_tag_protocol driver API. When that is introduced, we'll have to notify switches of the tagging protocol that they're configured to use. Currently the tag_ops structure pointer is held only for CPU ports. But there are switches which don't have CPU ports and nonetheless still need to be configured. These would be Marvell leaf switches whose upstream port is just a DSA link. How do we inform these of their tagging protocol setup/deletion? One answer to the above would be: iterate through the DSA switch tree's ports once, list the CPU ports, get their tag_ops, then iterate again now that we have it, and notify everybody of that tag_ops. But what to do if conflicts appear between one cpu_dp->tag_ops and another? There's no escaping the fact that conflict resolution needs to be done, so we can be upfront about it. Ease our work and just keep the master copy of the tag_ops inside the struct dsa_switch_tree. Reference counting is now moved to be per-tree too, instead of per-CPU port. There are many places in the data path that access master->dsa_ptr->tag_ops and we would introduce unnecessary performance penalty going through yet another indirection, so keep those right where they are. Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: dsa: document the existing switch tree notifiers and add a new one

2021-01-30T05:24:30Z

The existence of dsa_broadcast has generated some confusion in the past: https://www.mail-archive.com/netdev@vger.kernel.org/msg365042.html So let's document the existing dsa_port_notify and dsa_broadcast functions and explain when each of them should be used. Also, in fact, the in-between function has always been there but was lacking a name, and is the main reason for this patch: dsa_tree_notify. Refactor dsa_broadcast to use it. This patch also moves dsa_broadcast (a top-level function) to dsa2.c, where it really belonged in the first place, but had no companion so it stood with dsa_port_notify. Signed-off-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: Jakub Kicinski

net: dsa: add ops for devlink-sb

2021-01-16T04:02:34Z

Switches that care about QoS might have hardware support for reserving buffer pools for individual ports or traffic classes, and configuring their sizes and thresholds. Through devlink-sb (shared buffers), this is all configurable, as well as their occupancy being viewable. Add the plumbing in DSA for these operations. Individual drivers still need to call devlink_sb_register() with the shared buffers they want to expose. A helper was not created in DSA for this purpose (unlike, say, dsa_devlink_params_register), since in my opinion it does not bring any benefit over plainly calling devlink_sb_register() directly. Signed-off-by: Vladimir Oltean Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: Jakub Kicinski

net: dsa: set configure_vlan_while_not_filtering to true by default

2021-01-16T01:29:40Z

As explained in commit 54a0ed0df496 ("net: dsa: provide an option for drivers to always receive bridge VLANs"), DSA has historically been skipping VLAN switchdev operations when the bridge wasn't in vlan_filtering mode, but the reason why it was doing that has never been clear. So the configure_vlan_while_not_filtering option is there merely to preserve functionality for existing drivers. It isn't some behavior that drivers should opt into. Ideally, when all drivers leave this flag set, we can delete the dsa_port_skip_vlan_configuration() function. New drivers always seem to omit setting this flag, for some reason. So let's reverse the logic: the DSA core sets it by default to true before the .setup() callback, and legacy drivers can turn it off. This way, new drivers get the new behavior by default, unless they explicitly set the flag to false, which is more obvious during review. Remove the assignment from drivers which were setting it to true, and add the assignment to false for the drivers that didn't previously have it. This way, it should be easier to see how many we have left. The following drivers: lan9303, mv88e6060 were skipped from setting this flag to false, because they didn't have any VLAN offload ops in the first place. The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and therefore also inherits the configure_vlan_while_not_filtering=true behavior. Also, print a message through netlink extack every time a VLAN has been skipped. This is mildly annoying on purpose, so that (a) it is at least clear that VLANs are being skipped - the legacy behavior in itself is confusing, and the extack should be much more difficult to miss, unlike kernel logs - and (b) people have one more incentive to convert to the new behavior. No behavior change except for the added prints is intended at this time. $ ip link add br0 type bridge vlan_filtering 0 $ ip link set sw0p2 master br0 [ 60.315148] br0: port 1(sw0p2) entered blocking state [ 60.320350] br0: port 1(sw0p2) entered disabled state [ 60.327839] device sw0p2 entered promiscuous mode [ 60.334905] br0: port 1(sw0p2) entered blocking state [ 60.340142] br0: port 1(sw0p2) entered forwarding state Warning: dsa_core: skipping configuration of VLAN. # This was the pvid $ bridge vlan add dev sw0p2 vid 100 Warning: dsa_core: skipping configuration of VLAN. Signed-off-by: Vladimir Oltean Reviewed-by: Kurt Kanzenbach Reviewed-by: Florian Fainelli Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2021-01-15T02:34:50Z

Signed-off-by: Jakub Kicinski