kernel.git/net/dsa/Kconfig, branch linux-4.14.y

dsa: add support for Microchip KSZ tail tagging

2017-06-01T00:56:31Z

Adding support for the Microchip KSZ switch family tail tagging. Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: Woojung Huh Signed-off-by: David S. Miller

net: dsa: Sort DSA tagging protocol drivers

2017-05-17T19:19:40Z

With more tag protocols being added, regain some order by sorting the entries in various places. Signed-off-by: Andrew Lunn Reviewed-by: Vivien Didelot Signed-off-by: David S. Miller

net: dsa: add support for the SMSC-LAN9303 tagging format

2017-04-20T17:48:54Z

To define the outgoing port and to discover the incoming port a regular VLAN tag is used by the LAN9303. But its VID meaning is 'special'. This tag handler/filter depends on some hardware features which must be enabled in the device to provide and make use of this special VLAN tag to control the destination and the source of an ethernet packet. Signed-off-by: Juergen Borleis Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net-next: dsa: add Mediatek tag RX/TX handler

2017-04-07T20:50:55Z

Add the support for the 4-bytes tag for DSA port distinguishing inserted allowing receiving and transmitting the packet via the particular port. The tag is being added after the source MAC address in the ethernet header. Signed-off-by: Sean Wang Signed-off-by: Landen Chao Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: dsa: fix build error with devlink build as module

2017-04-02T03:10:20Z

After commit 96567d5dacf4 ("net: dsa: dsa2: Add basic support of devlink") I see the following link error with CONFIG_NET_DSA=y and CONFIG_NET_DEVLINK=m: net/built-in.o: In function 'dsa_register_switch': (.text+0xe226b): undefined reference to `devlink_alloc' net/built-in.o: In function 'dsa_register_switch': (.text+0xe2284): undefined reference to `devlink_register' net/built-in.o: In function 'dsa_register_switch': (.text+0xe243e): undefined reference to `devlink_port_register' net/built-in.o: In function 'dsa_register_switch': (.text+0xe24e1): undefined reference to `devlink_port_register' net/built-in.o: In function 'dsa_register_switch': (.text+0xe24fa): undefined reference to `devlink_port_type_eth_set' net/built-in.o: In function 'dsa_dst_unapply.part.8': dsa2.c:(.text.unlikely+0x345): undefined reference to 'devlink_port_unregister' dsa2.c:(.text.unlikely+0x36c): undefined reference to 'devlink_port_unregister' dsa2.c:(.text.unlikely+0x38e): undefined reference to 'devlink_port_unregister' dsa2.c:(.text.unlikely+0x3f2): undefined reference to 'devlink_unregister' dsa2.c:(.text.unlikely+0x3fb): undefined reference to 'devlink_free' Fix this by adding a dependency on MAY_USE_DEVLINK so that CONFIG_NET_DSA get switched to be build as module when CONFIG_NET_DEVLINK=m. Fixes: 96567d5dacf4 ("net: dsa: dsa2: Add basic support of devlink") Signed-off-by: Tobias Regnery Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: dsa: Remove hwmon support

2017-01-20T19:42:51Z

Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in DSA. The temperature sensor registers are actually in the embedded PHYs, and the PHY driver now supports it. So remove all HWMON support from DSA and drivers. Signed-off-by: Andrew Lunn Signed-off-by: David S. Miller

net: dsa: select NET_SWITCHDEV

2017-01-09T22:17:30Z

The support for DSA Ethernet switch chips depends on TCP/IP networking, thus explicit that HAVE_NET_DSA depends on INET. DSA uses SWITCHDEV, thus select it instead of depending on it. Signed-off-by: Vivien Didelot Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Tested-by: Randy Dunlap Signed-off-by: David S. Miller

net-next: dsa: add Qualcomm tag RX/TX handler

2016-09-16T08:31:51Z

Add support for the 2-bytes Qualcomm tag that gigabit switches such as the QCA8337/N might insert when receiving packets, or that we need to insert while targeting specific switch ports. The tag is inserted directly behind the ethernet header. Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: John Crispin Signed-off-by: David S. Miller

net: dsa: make NET_DSA manually selectable from the config

2015-03-21T01:37:58Z

Change bd76a116707bd2381da36cf7c3183df11293f1d6 made all DSA drivers depend on NET_DSA rather than selecting them. However, as the only way to select this option was to actually select a driver, it made DSA impossible to enable at all. This patch adds an explicit entry which the user will have to enable prior selecting a driver. Signed-off-by: Mathieu Olivari Signed-off-by: David S. Miller

dsa: change "select" to "depends on" for NET_SWITCHDEV and for NET_DSA

2015-03-16T20:29:18Z

This would fix randconfig compile error: net/built-in.o: In function `netdev_switch_fib_ipv4_abort': (.text+0xf7811): undefined reference to `fib_flush_external' Also it fixes following warnings: warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET) warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV) Reported-by: Randy Dunlap Suggested-by: Alexei Starovoitov Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller