kernel.git/drivers/w1/masters/Kconfig, branch linux-3.2.y

w1: W1_MASTER_DS1WM should depend on GENERIC_HARDIRQS

2011-06-16T03:04:00Z

On m68k (which doesn't support generic hardirqs yet): drivers/w1/masters/ds1wm.c: In function `ds1wm_probe': drivers/w1/masters/ds1wm.c: error: implicit declaration of function `irq_set_irq_type' Signed-off-by: Geert Uytterhoeven Cc: Evgeniy Polyakov Cc: Jean-Franois Dagenais Cc: Matt Reimer Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

w1: complete the 1-wire (w1) ds1wm driver search algorithm

2011-05-27T00:12:38Z

This adds multi-slave support of the w1 bus for the ds1wm Synthesizable 1-Wire Bus Master. Also many fixes and tweaks based on the rev3 of the datasheet http://datasheets.maxim-ic.com/en/ds/DS1WM.pdf Signed-off-by: Jean-François Dagenais Cc: Evgeniy Polyakov Cc: Szabolcs Gyurko Cc: Matt Reimer Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

omap: Start using CONFIG_SOC_OMAP

2011-01-28T00:39:40Z

We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest are nowadays just subcategories of these. Search and replace the following: ARCH_OMAP2420 SOC_OMAP2420 ARCH_OMAP2430 SOC_OMAP2430 ARCH_OMAP3430 SOC_OMAP3430 No functional changes. Signed-off-by: Tony Lindgren Signed-off-by: Thomas Weber Acked-by: Sourav Poddar

omap3: Replace ARCH_OMAP34XX with ARCH_OMAP3

2010-02-15T17:27:02Z

Replace ARCH_OMAP34XX with ARCH_OMAP3 Signed-off-by: Tony Lindgren

trivial: Kconfig: .ko is normally not included in module names

2009-06-12T16:01:50Z

.ko is normally not included in Kconfig help, make it consistent. Signed-off-by: Pavel Machek Signed-off-by: Jiri Kosina

w1: add 1-wire master driver for i.MX27 / i.MX31

2009-01-08T16:31:13Z

This patch adds support for the 1-wire master interface for i.MX27 and i.MX31. Signed-off-by: Luotao Fu Signed-off-by: Sascha Hauer Signed-off-by: Evgeniy Polyakov Cc: Russell King Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

W1_MASTER_DS1WM should depend on HAVE_CLK

2008-11-30T18:03:36Z

Uses clk_...() a lot Acked-by: rmk+kernel@arm.linux.org.uk Signed-off-by: Al Viro Signed-off-by: Linus Torvalds

hdq driver for OMAP2430/3430

2008-11-13T01:17:18Z

The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware protocol of the master functions of the Benchmark HDQ and the Dallas Semiconductor 1-Wire protocols. These protocols use a single wire for communication between the master (HDQ/1-Wire controller) and the slave (HDQ/1-Wire external compliant device). This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms. Signed-off-by: Madhusudhan Chikkature Acked-by: Felipe Balbi Acked-by: Evgeniy Polyakov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

w1-gpio: add GPIO w1 bus master driver

2008-02-06T18:41:15Z

Add a GPIO 1-wire bus master driver. The driver used the GPIO API to control the wire and the GPIO pin can be specified using platform data similar to i2c-gpio. The driver was tested with AT91SAM9260 + DS2401. Signed-off-by: Ville Syrjala Cc: Evgeniy Polyakov Cc: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

Use menuconfig objects: W1

2007-07-16T16:05:40Z

Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by: Jan Engelhardt Cc: Evgeniy Polyakov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds