kernel.git/drivers/usb/musb, branch linux-4.7.y

usb: musb: sunxi: Remove bogus "Frees glue" comment

2016-06-14T20:36:23Z

The comment is wrong, glue is devm_kzalloc-ed mem attached to the "allwinner,sun4i-a10-musb" compatible platform-dev. Where as glue->musb_pdev is a newly created "musb-hdrc" platform-dev. Signed-off-by: Hans de Goede [b-liu@ti.com: revise subject prefix] Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: sunxi: Fix NULL ptr deref when gadget is registered before musb

2016-06-14T20:36:23Z

Stop using the return value of platform_device_register_full() to get to the struct musb in sunxi_musb_work(). If a gadget has been registered (insmod-ed) before the musb driver, then musb_start will get called from the musb_core probe function and sunxi_musb_work() may run before platform_device_register_full() has returned. Instead store a pointer to struct musb in struct sunxi_glue when sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets called before sunxi_musb_work() can run. Signed-off-by: Hans de Goede [b-liu@ti.com: revise subject prefix] Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: Stop bulk endpoint while queue is rotated

2016-06-01T21:58:59Z

Ensure that the endpoint is stopped by clearing REQPKT before clearing DATAERR_NAKTIMEOUT before rotating the queue on the dedicated bulk endpoint. This addresses an issue where a race could result in the endpoint receiving data before it was reprogrammed resulting in a warning about such data from musb_rx_reinit before it was thrown away. The data thrown away was a valid packet that had been correctly ACKed which meant the host and device got out of sync. Signed-off-by: Andrew Goodbody Cc: stable@vger.kernel.org Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: Ensure rx reinit occurs for shared_fifo endpoints

2016-06-01T21:58:59Z

shared_fifo endpoints would only get a previous tx state cleared out, the rx state was only cleared for non shared_fifo endpoints Change this so that the rx state is cleared for all endpoints. This addresses an issue that resulted in rx packets being dropped silently. Signed-off-by: Andrew Goodbody Cc: stable@vger.kernel.org Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: host: correct cppi dma channel for isoch transfer

2016-06-01T21:58:59Z

Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(), which causes kernel NULL pointer reference oops later when calling cppi41_dma_channel_program(). Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c part1) Cc: # v4.2+ Reported-by: Matwey V. Kornilov Acked-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: only restore devctl when session was set in backup

2016-06-01T21:58:59Z

If the session bit was not set in the backup of devctl register, restoring devctl would clear the session bit. Therefor, only restore devctl register when the session bit was set in the backup. This solves the device enumeration failure in otg mode exposed by commit 56f487c (PM / Runtime: Update last_busy in rpm_resume). Cc: # v4.2+ Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: Use normal module_init for 2430 glue

2016-06-01T21:58:59Z

There's no longer any need for custom initcall level for musb. Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: Remove pm_runtime_set_irq_safe

2016-06-01T21:58:59Z

With the pull up being handled with delayed work, we can now finally remove pm_runtime_set_irq_safe that blocks the MUSB glue from idling. Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: Remove extra PM runtime calls from 2430 glue layer

2016-06-01T21:58:59Z

With PM runtime behaving, these are all now unnecessary. Doing pm_runtime_get(musb->controller) will keep the parent glue layer also active. Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman

usb: musb: Return error value from musb_mailbox

2016-06-01T21:58:59Z

At least on n900 we have phy-twl4030-usb only generating cable interrupts, and then have a separate USB PHY. In order for musb to know the real cable status, we need to clear any cached state until musb is ready. Otherwise the cable status interrupts will get just ignored if the status does not change from the initial state. To do this, let's add a return value to musb_mailbox(), and reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause a bit of churn here, I should have added that already last time patching musb_mailbox(). Signed-off-by: Tony Lindgren Signed-off-by: Bin Liu Signed-off-by: Greg Kroah-Hartman