kernel.git/drivers/usb/dwc2/core.c, branch linux-4.5.y

usb: dwc2: Add extra delay when forcing dr_mode

2016-02-17T08:31:42Z

Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For some reason, the existing msleep(25) is not enough after the force mode. The following patch was reported to fix the issue. This does increase the probe delay again slightly, but not up to the level it was before the original series of patches that this fixes. It does not cause any other issues when tested on Synopsys HAPS and Altera socfpga platforms. Need to revisit this series next release to see if we can address these issues without having an unconditional delay. Fixes: 09c96980dc72 ("usb: dwc2: Add functions to set and clear force mode") Reported-by: Caesar Wang Reported-by: Michael Niewoehner Tested-by: Heiko Stuebner Tested-by: Caesar Wang Signed-off-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: Fix probe problem on bcm2835

2016-02-03T18:15:49Z

Fixes an issue found on Raspberry PI platform that prevents probe. Don't skip setting the force mode if it's already set. Fixes: 09c96980dc72 ("usb: dwc2: Add functions to set and clear force mode") Tested-by: Heiko Stuebner Tested-by: Douglas Anderson Signed-off-by: John Youn Reported-by: Stefan Wahren Reported-by: Remi Pommarel Tested-by: Stefan Wahren Tested-by: Remi Pommarel Signed-off-by: Felipe Balbi

Revert "usb: dwc2: Move reset into dwc2_get_hwparams()"

2016-02-03T18:15:19Z

This reverts commit 263b7fb557f7 ("usb: dwc2: Move reset into dwc2_get_hwparams()") due to regression found on bcm2835 platform. USB ethernet fails, due to being unable to pick up proper parameters when performing a plain reset before reading hw params. Below shows the results of the gnptxfsiz and hptxfsiz with and before and after reverting this (from Stefan Wahren): So here is the probe result before Patch 1 is applied: [ 1.283148] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host [ 1.313894] dwc2 20980000.usb: gnptxfsiz=00201000 [ 1.314104] dwc2 20980000.usb: hptxfsiz=00000000 [ 1.353908] dwc2 20980000.usb: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration. [ 1.354262] dwc2 20980000.usb: 512 invalid for host_perio_tx_fifo_size. Check HW configuration. [ 1.394249] dwc2 20980000.usb: DWC OTG Controller [ 1.394561] dwc2 20980000.usb: new USB bus registered, assigned bus number 1 [ 1.394917] dwc2 20980000.usb: irq 33, io mem 0x00000000 And here is the probe result after Patch 1 is applied: [ 1.280107] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host [ 1.353949] dwc2 20980000.usb: gnptxfsiz=01001000 [ 1.354166] dwc2 20980000.usb: hptxfsiz=02002000 [ 1.434301] dwc2 20980000.usb: DWC OTG Controller [ 1.434616] dwc2 20980000.usb: new USB bus registered, assigned bus number 1 [ 1.434973] dwc2 20980000.usb: irq 33, io mem 0x00000000 Tested-by: Heiko Stuebner Tested-by: Douglas Anderson Signed-off-by: John Youn Reported-by: Stefan Wahren Reported-by: Remi Pommarel Tested-by: Stefan Wahren Tested-by: Remi Pommarel Signed-off-by: Felipe Balbi

usb: dwc2: Reduce delay when forcing mode in reset

2015-12-22T18:01:32Z

The delay for force mode is only 25ms according to the databook. Signed-off-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: Improve handling of host and device hwparams

2015-12-22T18:00:51Z

Adds separate functions to get the host and device specific hardware parameters. The functions check whether the parameters need to be read at all, depending on dr_mode, and forces the mode only if necessary. This saves some delays during probe. This also adds two device mode parameters that will be used by the gadget. Signed-off-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: Add functions to set and clear force mode

2015-12-22T18:00:34Z

Added functions to set force mode for host and device. These functions will check the current mode and only force if needed thus avoiding unnecessary force mode delays. However clearing the mode is currently done unconditionally and with the delay in place. This is needed during the connector ID status change interrupt in order to ensure that the mode has changed properly. This preserves the old behavior only for this case. The warning comment about this is moved into the clear mode condition. Signed-off-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: Move reset into dwc2_get_hwparams()

2015-12-22T17:58:34Z

The reset is required to get reset values of the hardware parameters but the force mode is not. Move the base reset into dwc2_get_hwparams() and do the reset and force mode afterwards. Signed-off-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: Add functions to check the HW OTG config

2015-12-22T17:55:46Z

Added functions to query the GHWCFG2.OTG_MODE. This tells us whether the controller hardware is configured for OTG, device-only, or host-only. Signed-off-by: John Youn Tested-by: Douglas Anderson Reviewed-by: Douglas Anderson Signed-off-by: Felipe Balbi

usb: dwc2: Add dwc2_core_reset()

2015-12-22T17:55:32Z

dwc2_core_reset() was previously renamed to dwc2_core_reset_and_dr_force_mode(). Now add back dwc2_core_reset() which performs only a basic core reset without forcing the mode. Signed-off-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: Rename dwc2_core_reset()

2015-12-22T17:55:21Z

Renamed dwc2_core_reset() to dwc2_core_reset_and_force_dr_mode(). This describes what it is doing more accurately. This is in preparation of introducing a plain dwc2_core_reset() function that only performs the reset and doesn't force the mode. Signed-off-by: John Youn Signed-off-by: Felipe Balbi