kernel.git/drivers/usb/core/message.c, branch linux-2.6.34.y

USB: disable endpoints after unbinding interfaces, not before

2011-01-06T23:08:25Z

commit 80f0cf3947889014d3a3dc0ad60fb87cfda4b12a upstream. This patch (as1430) fixes a bug in usbcore. When a device configuration change occurs or a device is removed, the endpoints for the old config should be completely disabled. However it turns out they aren't; this is because usb_unbind_interface() calls usb_enable_interface() or usb_set_interface() to put interfaces back in altsetting 0, which re-enables the interfaces' endpoints. As a result, when a device goes through a config change or is unconfigured, the ep_in[] and ep_out[] arrays may be left holding old pointers to usb_host_endpoint structures. If the device is deauthorized these structures get freed, and the stale pointers cause errors when the the device is eventually unplugged. The solution is to disable the endpoints after unbinding the interfaces instead of before. This isn't as large a change as it sounds, since usb_unbind_interface() disables all the interface's endpoints anyway before calling the driver's disconnect routine, unless the driver claims to support "soft" unbind. This fixes Bugzilla #19192. Thanks to "Tom" Lei Ming for diagnosing the underlying cause of the problem. Signed-off-by: Alan Stern Tested-by: Carsten Sommer Signed-off-by: Greg Kroah-Hartman Signed-off-by: Paul Gortmaker

USB: fix bug in initialization of interface minor numbers

2011-01-06T23:08:07Z

commit 0026e00523a85b90a92a93ddf6660939ecef3e54 upstream. Recent changes in the usbhid layer exposed a bug in usbcore. If CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned a minor number of 0. However interfaces that aren't registered as USB class devices also have their minor number set to 0, during initialization. As a result usb_find_interface() may return the wrong interface, leading to a crash. This patch (as1418) fixes the problem by initializing every interface's minor number to -1. It also cleans up the usb_register_dev() function, which besides being somewhat awkwardly written, does not unwind completely on all its error paths. Signed-off-by: Alan Stern Tested-by: Philip J. Turmel Tested-by: Gabriel Craciunescu Tested-by: Alex Riesen Tested-by: Matthias Bayer CC: Jiri Kosina Signed-off-by: Greg Kroah-Hartman Signed-off-by: Paul Gortmaker

USB: fix usbmon and DMA mapping for scatter-gather URBs

2010-07-05T18:22:07Z

commit ff9c895f07d36193c75533bda8193bde8ca99d02 upstream. This patch (as1368) fixes a rather obscure bug in usbmon: When tracing URBs sent by the scatter-gather library, it accesses the data buffers while they are still mapped for DMA. The solution is to move the mapping and unmapping out of the s-g library and into the usual place in hcd.c. This requires the addition of new URB flag bits to describe the kind of mapping needed, since we have to call dma_map_sg() if the HCD supports native scatter-gather operation and dma_map_page() if it doesn't. The nice thing about having the new flags is that they simplify the testing for unmapping. The patch removes the only caller of usb_buffer_[un]map_sg(), so those functions are #if'ed out. A later patch will remove them entirely. As a result of this change, urb->sg will be set in situations where it wasn't set previously. Hence the xhci and whci drivers are adjusted to test urb->num_sgs instead, which retains its original meaning and is nonzero only when the HCD has to handle a scatterlist. Finally, even when a submission error occurs we don't want to hand URBs to usbmon before they are unmapped. The submission path is rearranged so that map_urb_for_dma() is called only for non-root-hub URBs and unmap_urb_for_dma() is called immediately after a submission error. This simplifies the error handling. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()

2010-03-02T22:55:10Z

While looping over the interfaces, if usb_hcd_alloc_bandwidth() fails it calls hcd->driver->reset_bandwidth(), so there was no need to reinstate the interface again. If no break occurred, the index equals config->desc.bNumInterfaces. A subsequent usb_control_msg() failure resulted in a read from config->interface[config->desc.bNumInterfaces] at label reset_old_alts. In either case the last interface should be skipped. Signed-off-by: Roel Kluin Acked-by: Alan Stern Acked-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman

USB: trivial: missing newline in usb core warning message

2010-03-02T22:54:36Z

Signed-off-by: Thadeu Lima de Souza Cascardo Signed-off-by: Greg Kroah-Hartman

USB: convert to the runtime PM framework

2010-03-02T22:54:12Z

This patch (as1329) converts the USB stack over to the PM core's runtime PM framework. This involves numerous changes throughout usbcore, especially to hub.c and driver.c. Perhaps the most notable change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME instead of CONFIG_PM. Several fields in the usb_device and usb_interface structures are no longer needed. Some code which used to depend on CONFIG_USB_PM now depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header files). The only visible change in behavior should be that following a system sleep (resume from RAM or resume from hibernation), autosuspended USB devices will be resumed just like everything else. They won't remain suspended. But if they aren't in use then they will naturally autosuspend again in a few seconds. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

PM: Allow USB devices to suspend/resume asynchronously

2010-02-26T19:39:12Z

Set power.async_suspend for USB devices, endpoints and interfaces, allowing them to be suspended and resumed asynchronously during system sleep transitions. The power.async_suspend flag is also set for devices that don't have suspend or resume callbacks, because otherwise they would make the main suspend/resume thread wait for their "asynchronous" children (during suspend) or parents (during resume), effectively negating the possible gains from executing these devices' suspend and resume callbacks asynchronously. Signed-off-by: Rafael J. Wysocki

USB: Don't use GFP_KERNEL while we cannot reset a storage device

2010-01-20T23:24:34Z

Memory allocations with GFP_KERNEL can cause IO to a storage device which can fail resulting in a need to reset the device. Therefore GFP_KERNEL cannot be safely used between usb_lock_device() and usb_unlock_device(). Replace by GFP_NOIO. Signed-off-by: Oliver Neukum Cc: stable Cc: Alan Stern Signed-off-by: Greg Kroah-Hartman

USB: core: message: fix sparse warning

2009-12-11T19:55:28Z

Fix the following sparse warning: drivers/usb/core/message.c:1583:6: warning: symbol '__usb_queue_reset_device' was not declared. Should it be static? Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

USB: Check bandwidth when switching alt settings.

2009-12-11T19:55:27Z

Make the USB core check the bandwidth when switching from one interface alternate setting to another. Also check the bandwidth when resetting a configuration (so that alt setting 0 is used). If this check fails, the device's state is unchanged. If the device refuses the new alt setting, re-instate the old alt setting in the host controller hardware. If a USB device doesn't have an alternate interface setting 0, install the first alt setting in its descriptors when a new configuration is requested, or the device is reset. Add a mutex per root hub to protect bandwidth operations: adding/reseting/changing configurations, and changing alternate interface settings. We want to ensure that the xHCI host controller and the USB device are set up for the same configurations and alternate settings. There are two (possibly three) steps to do this: 1. The host controller needs to check that bandwidth is available for a different setting, by issuing and waiting for a configure endpoint command. 2. Once that returns successfully, a control message is sent to the device. 3. If that fails, the host controller must be notified through another configure endpoint command. The mutex is used to make these three operations seem atomic, to prevent another driver from using more bandwidth for a different device while we're in the middle of these operations. While we're touching the bandwidth code, rename usb_hcd_check_bandwidth() to usb_hcd_alloc_bandwidth(). This function does more than just check that the bandwidth change won't exceed the bus bandwidth; it actually changes the bandwidth configuration in the xHCI host controller. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman