Hosts the 0x221E linux distro kernel. https://git.0xinfinity.dev/distro/kernel.git/atom?h=linux-5.10.y 2025-01-09T12:24:51Z 2025-01-09T12:24:51Z Roger Quadros 2024-07-28T16:09:37Z urn:sha1:4ba1ee910938800f0599f714f1abdf06203cccc9 [ Upstream commit 0aca19e4037a4143273e90f1b44666b78b4dde9b ] Some platforms (e.g. ti,j721e-usb, ti,am64-usb) require this bit to be set to workaround a lockup issue with PHY short suspend intervals [1]. Add a platform quirk flag to indicate if Suspend Residency should be enabled. [1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf i2409 - USB: USB2 PHY locks up due to short suspend Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20240516044537.16801-2-r-gunasekaran@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 2022-12-02T16:40:03Z Pawel Laszczak 2020-12-07T10:32:18Z urn:sha1:8382cdf0ab5df84cae9603de927145a7f140b937 [ Upstream commit db8892bb1bb64b6e3d1381ac342a2ee31e1b76b6 ] Patch adds support for Cadence DRD Super Speed Plus controller(CDNSP). CDNSP DRD is a part of Cadence CDNSP controller. The DRD CDNSP controller has a lot of difference on hardware level but on software level is quite compatible with CDNS3 DRD. For this reason CDNS3 DRD part of CDNS3 driver was reused for CDNSP driver. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Tested-by: Aswath Govindraju <a-govindraju@ti.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Stable-dep-of: 9d5333c93134 ("usb: cdns3: host: fix endless superspeed hub port reset") Signed-off-by: Sasha Levin <sashal@kernel.org> 2020-10-02T06:57:40Z Peter Chen 2020-09-01T02:33:51Z urn:sha1:9f650135945fb5dba6bd6340ce834570fe0686f2 Some PHYs may need to enter related mode, and do some settings. Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> 2020-10-02T06:57:39Z Pawel Laszczak 2020-09-15T11:45:43Z urn:sha1:2eae2dfd581420f94d6041dddc7a88d7ae9ce2ff USB2.0 PHY hangs in Rx Compliance test when the incoming packet amplitude is varied below and above the Squelch Level of Receiver during the active packet multiple times. Version 1 of the controller allows PHY to be reset when RX fail condition is detected to work around the above issue. This feature is disabled by default and needs to be enabled using a bit from the newly added PHYRST_CFG register. This patch enables the workaround. There is no way to know controller version before device controller is started and the workaround needs to be applied for both host and device modes, so we rely on a DT property do decide when to apply the workaround. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> 2020-10-02T06:57:38Z Peter Chen 2020-09-02T09:57:32Z urn:sha1:b1234e3b3b265588bab1e7a28508621045b87efa Introduce runtime PM and wakeup interrupt handler for cdns3, the runtime PM is default off since other cdns3 may not implement glue layer support for runtime PM. One typical wakeup event use case is xHCI runtime suspend will clear USBCMD.RS bit, after that the xHCI will not trigger any interrupts, so its parent (cdns core device) needs to resume xHCI device when any (wakeup) events occurs at host port. When the controller is in low power mode, the lpm flag will be set. The interrupt triggered later than lpm flag is set considers as wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup occurs, it first disables interrupt to avoid later interrupt occurrence since the controller is in low power mode at that time, and access registers may be invalid at that time. At wakeup handler, it will call pm_request_resume to wakeup xHCI device, and at runtime resume handler, it will enable interrupt again. The API platform_suspend is introduced for glue layer to implement platform specific PM sequence. Reviewed-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> 2020-07-24T13:45:13Z Pawel Laszczak 2020-07-13T10:05:54Z urn:sha1:b2aeb6da3d6ee562e57ad3a7d73a7de0c36ce8eb Patch split function cdns3_drd_switch_gadget and cdns3_drd_switch_host into: - cdns3_drd_host_on - cdns3_drd_host_off - cdns3_drd_gadget_on - cdns3_drd_gadgett_off These functions don't have any shared code so it's better to have smaller, faster and easier functions. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> 2020-07-24T13:45:13Z Pawel Laszczak 2020-07-13T10:05:51Z urn:sha1:08c35dd3cc2184dcc952fc845329dcae1ee302d3 Patch adds 2 definitions that make it easier to understand the code. Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> 2020-07-24T13:45:13Z Pawel Laszczak 2020-07-13T10:05:50Z urn:sha1:245258495a5157e4428bd944189e4062d852dcdd Patch changes return type from int to bool for cdns3_is_host and cdns3_is_device functions. Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> 2020-07-24T13:45:12Z Pawel Laszczak 2020-07-13T10:05:49Z urn:sha1:03cce68a828dba13b3715033e5133839820218c3 IRQ_NONE can be returned indirect. Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> 2020-07-24T13:45:12Z Pawel Laszczak 2020-07-13T10:05:48Z urn:sha1:ecf4f823fb7050e4f450bb56cd403cbb6d41ca7c Patch deletes unnecessary != from condition statement in cdns3_drd_init function. Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>