kernel.git/drivers/thunderbolt/tb.c, branch linux-5.12.y

thunderbolt: Increase runtime PM reference count on DP tunnel discovery

2021-03-08T11:22:42Z

If the driver is unbound and then bound back it goes over the topology and figure out the existing tunnels. However, if it finds DP tunnel it should make sure the domain does not runtime suspend as otherwise it will tear down the DP tunnel unexpectedly. Fixes: 6ac6faee5d7d ("thunderbolt: Add runtime PM for Software CM") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg

thunderbolt: Add support for native USB4 _OSC

2021-02-04T07:45:25Z

ACPI 6.4 introduced a new _OSC capability used to negotiate whether the OS is supposed to use Software (native) or Firmware based Connection Manager. If the native support is granted then there are set of bits that enable/disable different tunnel types that the Software Connection Manager is allowed to tunnel. This adds support for this new USB4 _OSC accordingly. When PCIe tunneling is disabled then the driver switches security level to be "nopcie" following the security level 5 used in Firmware based Connection Manager. Signed-off-by: Mika Westerberg Acked-by: Yehezkel Bernat

thunderbolt: Allow disabling XDomain protocol

2021-02-04T07:45:25Z

This allows disabling XDomain protocol completely if the user does not plan to use the USB4/Thunderbolt peer-to-peer functionality, or for security reasons. XDomain protocol is enabled by default but with this commit it is possible to disable it by passing "xdomain=0" as module parameter (or through the kernel command line). Signed-off-by: Mika Westerberg Acked-by: Yehezkel Bernat

thunderbolt: tb: Kernel-doc function headers should document their parameters

2021-01-28T10:44:24Z

Fixes the following W=1 kernel build warning(s): drivers/thunderbolt/tb.c:535: warning: Function parameter or member 'sw' not described in 'tb_scan_switch' drivers/thunderbolt/tb.c:551: warning: Function parameter or member 'port' not described in 'tb_scan_port' drivers/thunderbolt/tb.c:711: warning: Function parameter or member 'tb' not described in 'tb_free_invalid_tunnels' drivers/thunderbolt/tb.c:726: warning: Function parameter or member 'sw' not described in 'tb_free_unplugged_children' drivers/thunderbolt/tb.c:1129: warning: Function parameter or member 'work' not described in 'tb_handle_hotplug' drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'tb' not described in 'tb_handle_event' drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'type' not described in 'tb_handle_event' drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'buf' not described in 'tb_handle_event' drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'size' not described in 'tb_handle_event' drivers/thunderbolt/tb.c:1239: warning: expecting prototype for tb_schedule_hotplug_handler(). Prototype was for tb_handle_event() instead Cc: Andreas Noever Cc: Michael Jamet Cc: Yehezkel Bernat Cc: linux-usb@vger.kernel.org Signed-off-by: Lee Jones Signed-off-by: Mika Westerberg

thunderbolt: Add support for de-authorizing devices

2021-01-15T07:53:06Z

In some cases it is useful to be able de-authorize devices. For example if user logs out the userspace can have a policy that disconnects PCIe devices until logged in again. This is only possible for software based connection manager as it directly controls the tunnels. For this reason make the authorized attribute accept writing 0 which makes the software connection manager to tear down the corresponding PCIe tunnel. Userspace can check if this is supported by reading a new domain attribute deauthorization, that holds 1 in that case. While there correct tb_domain_approve_switch() kernel-doc and description of authorized attribute to mention that it is only about PCIe tunnels. Cc: Christian Kellner Signed-off-by: Mika Westerberg Acked-by: Yehezkel Bernat

thunderbolt: Log which connection manager implementation is used

2020-11-30T11:39:23Z

This makes it easier to figure out whether the driver is using firmware or software based connection manager implementation. Signed-off-by: Mika Westerberg

thunderbolt: Only stop control channel when entering freeze

2020-09-16T11:57:46Z

According to the kernel power management documentation freeze phase should only quiesce the device, no need to configure wakes or put it to low power state. For this reason we simply stop the control channel and in case of Software Connection Manager also mark the hotplug disabled. This should align the driver better with the PM framework expectations. Signed-off-by: Mika Westerberg

thunderbolt: Add runtime PM for Software CM

2020-09-03T09:06:42Z

This adds runtime PM support for the Software Connection Manager parts of the driver. This allows to save power when either there is no device attached at all or there is a device attached and all following conditions are true: - Tunneled PCIe root/downstream ports are runtime suspended - Tunneled USB3 ports are runtime suspended - No active DisplayPort stream - No active XDomain connection For the first two we take advantage of device links that were added in previous patch. Difference for the system sleep case is that we also enable wakes when something is geting plugged in/out of the Thunderbolt ports. Signed-off-by: Mika Westerberg

thunderbolt: Disable lane 1 for XDomain connection

2020-09-03T09:06:41Z

USB4 spec mandates that the lane 1 should be disabled if lanes are not bonded. For host-to-host connections (XDomain) we don't support lane bonding so in order to be compatible with the spec, disable lane 1 when another host is connected. Signed-off-by: Mika Westerberg

thunderbolt: Configure port for XDomain

2020-09-03T09:06:41Z

When the port is connected to another host it should be marked as such in the USB4 port capability. This information is used by the router during sleep and wakeup. Also do the same for legacy switches via link controller vendor specific registers. Signed-off-by: Mika Westerberg