kernel.git/drivers/thunderbolt/icm.c, branch linux-5.5.y

thunderbolt: Do not start firmware unless asked by the user

2019-11-02T09:13:31Z

Since now we can do pretty much the same thing in the software connection manager than the firmware would do, there is no point starting it by default. Instead we can just continue using the software connection manager. Make it possible for user to switch between the two by adding a module pararameter (start_icm) which is by default false. Having this ability to enable the firmware may be useful at least when debugging possible issues with the software connection manager implementation. Signed-off-by: Mika Westerberg

thunderbolt: Add support for lane bonding

2019-11-02T09:13:31Z

Lane bonding allows aggregating two 10/20 Gb/s (depending on the generation) lanes into a single 20/40 Gb/s bonded link. This allows sharing the full bandwidth more efficiently. In order to establish lane bonding we need to check that lane bonding is possible through link controller and that both ends of the link actually supports 2x widths. This also means that all the paths should be established through the primary port so update tb_path_alloc() to handle this as well. Lane bonding is supported starting from Falcon Ridge (2nd generation) controllers. We also expose the current speed and number of lanes under each device except the host router following similar attribute naming than USB bus. Expose speed and number of lanes for both directions to allow possibility of asymmetric link in the future. Signed-off-by: Mika Westerberg

thunderbolt: Refactor add_switch() into two functions

2019-11-01T11:32:00Z

Currently add_switch() takes a huge amount of parameters that makes it hard to maintain. Instead of passing all those parameters we can split the function into two parts (alloc and add) and fill the additional switch fields directly in the functions calling those. While there remove redundant error logging in case kmemdup() fails. No functional changes. Signed-off-by: Mika Westerberg

thunderbolt: Add helper macro to iterate over switch ports

2019-11-01T11:32:00Z

There are quite many places in the driver where we iterate over each port in the switch. To make it bit more convenient, add a macro that can be used to iterate over each port and convert existing call sites to use it. This is based on code by Lukas Wunner. No functional changes. Signed-off-by: Mika Westerberg

thunderbolt: Add support for Intel Ice Lake

2019-08-26T09:15:06Z

The Thunderbolt controller is integrated into the Ice Lake CPU itself and requires special flows to power it on and off using force power bit in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from the discrete solutions. Now the firmware notifies the driver whether RTD3 entry or exit are possible. The driver is responsible of sending Go2Sx command through link controller mailbox when system enters Sx states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow Titan Ridge. Signed-off-by: Raanan Avargil Signed-off-by: Mika Westerberg Reviewed-by: Yehezkel Bernat Tested-by: Mario Limonciello

thunderbolt: Move NVM upgrade support flag to struct icm

2019-08-26T09:14:32Z

This is depends on the controller and on the platform/CPU we are running. Move it to struct icm so we can set it per controller. Signed-off-by: Mika Westerberg Reviewed-by: Yehezkel Bernat Tested-by: Mario Limonciello

thunderbolt: Implement CIO reset correctly for Titan Ridge

2019-06-14T11:25:43Z

When starting ICM firmware on Apple systems we need to perform CIO reset as part of the flow. However, it turns out that the reset register has changed to another location in Titan Ridge. Fix this by introducing ->cio_reset() callback with corresponding implementations for Alpine and Titan Ridge. Fixes: c4630d6ae6e3 ("thunderbolt: Start firmware on Titan Ridge Apple systems") Reported-by: Peter Bowen Signed-off-by: Mika Westerberg

thunderbolt: Make sure device runtime resume completes before taking domain lock

2019-06-12T10:30:46Z

When a device is authorized from userspace by writing to authorized attribute we first take the domain lock and then runtime resume the device in question. There are two issues with this. First is that the device connected notifications are blocked during this time which means we get them only after the authorization operation is complete. Because of this the authorization needed flag from the firmware notification is not reflecting the real authorization status anymore. So what happens is that the "authorized" keeps returning 0 even if the device was already authorized properly. Second issue is that each time the controller is runtime resumed the connection_id field of device connected notification may be different than in the previous resume. We need to use the latest connection_id otherwise the firmware rejects the authorization command. Fix these by moving runtime resume operations to happen before the domain lock is taken, and waiting for the updated device connected notification from the firmware before we allow runtime resume of a device to complete. While there add missing locking to tb_switch_nvm_read(). Fixes: 09f11b6c99fe ("thunderbolt: Take domain lock in switch sysfs attribute callbacks") Reported-by: Pengfei Xu Signed-off-by: Mika Westerberg

thunderbolt: Start firmware on Titan Ridge Apple systems

2019-04-18T08:18:54Z

Titan Ridge flow to start the firmware is the same as Alpine Ridge so we can do the same on Titan Ridge based Apple systems. Signed-off-by: Mika Westerberg

thunderbolt: Make rest of the logging to happen at debug level

2019-04-18T08:18:53Z

Now that the driver can handle every possible tunnel types there is no point to log everything as info level so turn these to happen at debug level instead. While at it remove duplicated tunnel activation log message (tb_tunnel_activate() calls tb_tunnel_restart() which print the same message) and add one missing '\n' termination. Signed-off-by: Mika Westerberg