kernel.git/drivers/spi/Kconfig, branch linux-2.6.33.y

Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6

2009-12-17T23:59:05Z

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: spi: spi_txx9.c: use resource_size() spi: spi_sh_sci.c: use resource_size() spi: spi_mpc8xxx.c: use resource_size() spi: spi_bfin5xx.c: use resource_size() spi: atmel_spi.c: use resource_size() spi: Add s3c64xx SPI Controller driver atmel_spi: fix dma addr calculation for len > BUFFER_SIZE spi_s3c24xx: add FIQ pseudo-DMA support spi: controller driver for Designware SPI core spidev: add proper section markers spidev: use DECLARE_BITMAP instead of declaring the array

spi: Add s3c64xx SPI Controller driver

2009-12-17T15:58:17Z

Each SPI controller has exactly one CS line and as such doesn't provide for multi-cs. We implement a workaround to support multi-cs by _not_ configuring the mux'ed CS pin for each SPI controller. The CS mechanism is assumed to be fully machine specific - the driver doesn't even assume some GPIO pin is used to control the CS. The driver selects between DMA and POLLING mode depending upon the xfer size - DMA mode for xfers bigger than FIFO size, POLLING mode otherwise. The driver has been designed to be capable of running SoCs since s3c64xx and till date, for that reason some of the register fields have been passed via, SoC specific, platform data. Signed-off-by: Jassi Brar Signed-off-by: Grant Likely

spi_s3c24xx: add FIQ pseudo-DMA support

2009-12-17T15:57:01Z

Add pseudo-DMA by FIQ to the S3C24XX SPI driver. This allows the driver to get DMA-like performance where there are either no free DMA channels or when doing transfers that required both TX and RX data paths. Since this patch requires the addition of an assembly file to hold the FIQ code, we rename the module (instead of adding a rename of the .c file to this patch). We expect most users are loading this via udev and thus there should be no change to the userland configuration. Signed-off-by: Ben Dooks Signed-off-by: Simtec Linux Team Cc: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Grant Likely

spi: controller driver for Designware SPI core

2009-12-17T15:39:13Z

Driver for the Designware SPI core, it supports multipul interfaces like PCI/APB etc. User can use "dw_apb_ssi_db.pdf" from Synopsys as HW datasheet. [randy.dunlap@oracle.com: fix build] [akpm@linux-foundation.org: build fix] Signed-off-by: Feng Tang Cc: David Brownell Signed-off-by: Randy Dunlap Signed-off-by: Andrew Morton Signed-off-by: Grant Likely

Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6

2009-12-14T18:22:11Z

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits) spi: fix probe/remove section markings Add OMAP spi100k driver spi-imx: don't access struct device directly but use dev_get_platdata spi-imx: Add mx25 support spi-imx: use positive logic to distinguish cpu variants spi-imx: correct check for platform_get_irq failing ARM: NUC900: Add spi driver support for nuc900 spi: SuperH MSIOF SPI Master driver V2 spi: fix spidev compilation failure when VERBOSE is defined spi/au1550_spi: fix setupxfer not to override cfg with zeros spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove spi/i.MX: fix broken error handling for gpio_request spi/i.mx: drain MXC SPI transfer buffer when probing device MAINTAINERS: add SPI co-maintainer. spi/xilinx_spi: fix incorrect casting spi/mpc52xx-spi: minor cleanups xilinx_spi: add a platform driver using the xilinx_spi common module. xilinx_spi: add support for the DS570 IP. xilinx_spi: Switch to iomem functions and support little endian. xilinx_spi: Split into of driver and generic part. ...

Add OMAP spi100k driver

2009-12-13T08:02:11Z

This change adds the OMAP SPI 100k driver created by Fabrice Crohas . This SPI bus is found on OMAP7xx-series smartphones, and for many, the touchscreen is attached to this bus. The lion's share of the work was done by Fabrice on this driver -- I am merely porting it from the Linwizard project on his behalf. Signed-off-by: Cory Maccarrone Signed-off-by: Grant Likely

ARM: NUC900: Add spi driver support for nuc900

2009-12-13T07:58:00Z

Signed-off-by: Wan ZongShun Signed-off-by: Grant Likely

spi: SuperH MSIOF SPI Master driver V2

2009-12-13T07:48:27Z

This patch is V2 of SPI Master support for the SuperH MSIOF. Full duplex, spi mode 0-3, active high cs, 3-wire and lsb first should all be supported, but the driver has so far only been tested with "mmc_spi". The MSIOF hardware comes with 32-bit FIFOs for receive and transmit, and this driver simply breaks the SPI messages into FIFO-sized chunks. The MSIOF hardware manages the pins for clock, receive and transmit (sck/miso/mosi), but the chip select pin is managed by software and must be configured as a regular GPIO pin by the board code. Performance wise there is still room for improvement, but on a Ecovec board with the built-in sh7724 MSIOF0 this driver gets Mini-sd read speeds of about half a megabyte per second. Future work include better clock setup and merging of 8-bit transfers into 32-bit words to reduce interrupt load and improve throughput. Signed-off-by: Magnus Damm Signed-off-by: Grant Likely

Merge commit 'gcl/next' into next

2009-12-09T06:10:22Z

xilinx_spi: add a platform driver using the xilinx_spi common module.

2009-12-09T01:48:14Z

This patch adds in a platform device driver using the xilinx_spi common module. Tested-by: John Linn Signed-off-by: Richard Röjfors Signed-off-by: Grant Likely