kernel.git/drivers/regulator/Makefile, branch linux-2.6.32.y

Regulator: Adding TPS65023 and TPS6507x in Kconfig and Makefile

2009-09-22T12:32:42Z

Adding TPS65023 and TPS6507x regulator driver support in drivers/regulator/Makefile and drivers/regulator/Kconfig Signed-off-by: Anuj Aggarwal Acked-by: Mark Brown Signed-off-by: Liam Girdwood

regulator: AB3100 support

2009-09-17T07:47:25Z

This adds support for the regulators found in the AB3100 Mixed-Signal IC. It further also defines platform data for the ST-Ericsson U300 platform and extends the AB3100 MFD driver so that platform/board data with regulation constraints and an init function can be passed down all the way from the board to the regulators. Signed-off-by: Linus Walleij Acked-by: Mark Brown Signed-off-by: Liam Girdwood Signed-off-by: Samuel Ortiz

regulator: Add Freescale MC13783 driver

2009-09-17T07:47:19Z

This driver provides basic support for the voltage regulators integrated into the Freescale MC13783 PMIC. It is currently only possible to enable/disable outputs, not to actually set the voltage. Signed-off-by: Sascha Hauer Signed-off-by: Liam Girdwood Signed-off-by: Samuel Ortiz

regulator: Add WM831x ISINK support

2009-09-17T07:47:11Z

The WM831x series of PMICs provide two constant current sinks designed to drive strings of serially connected LEDs for applications such as backlights. This driver adds support for those regulators. Signed-off-by: Mark Brown Acked-by: Liam Girdwood Signed-off-by: Samuel Ortiz

regulator: Add WM831x LDO support

2009-09-17T07:47:09Z

The WM831x series of devices provide three types of LDO: - General purpose LDOs supporting voltages from 0.9-3.3V - High performance analogue LDOs supporting voltages from 1-3.5V - Very low power consumption LDOs intended to support always on functionality. This patch adds support for all three kinds of LDO. Each regulator is probed as an individual platform device with resources used to provide the register map location of the regulator. Mixed hardware and software control of regulators is not current supported. Signed-off-by: Mark Brown Acked-by: Liam Girdwood Signed-off-by: Samuel Ortiz

regulator: Add WM831x DC-DC buck convertor support

2009-09-17T07:47:06Z

The WM831x series of devices all have 3 DC-DC buck convertors. This driver implements software control for these regulators via the regulator API. Use with split hardware/software control of individual regulators is not supported, though regulators not controlled by software may be controlled via the hardware control interfaces. Signed-off-by: Mark Brown Acked-by: Liam Girdwood Signed-off-by: Samuel Ortiz

regulator: add pcap driver

2009-09-17T07:46:49Z

Add (partial) support for the voltage regulators on the PCAP2 PMIC. Signed-off-by: Daniel Ribeiro Signed-off-by: Liam Girdwood Signed-off-by: Samuel Ortiz

LP3971 PMIC regulator driver (updated and combined version)

2009-06-15T10:18:26Z

This patch adds regulator drivers for National Semiconductors LP3971 PMIC. This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface. Reviewed-by: Kyungmin Park Signed-off-by: Marek Szyprowski Acked-by: Mark Brown Signed-off-by: Liam Girdwood

regulator: add userspace-consumer driver

2009-06-15T10:18:22Z

The userspace-consumer driver allows control of voltage and current regulator state from userspace. This is required for fine-grained power management of devices that are completely controller by userspace applications, e.g. a GPS transciever connected to a serial port. Signed-off-by: Mike Rapoport Acked-by: Mark Brown Signed-off-by: Liam Girdwood

Maxim 1586 regulator driver

2009-06-15T10:18:22Z

The Maxim 1586 regulator is a voltage regulator with 2 voltage outputs, specially suitable for Marvell PXA chips. One output is in the range of required VCC_CORE by the PXA27x chips, the other in the VCC_USIM required as well by PXA27x chips. The chip is controlled through the I2C bus. Signed-off-by: Robert Jarzmik Acked-by: Mark Brown Signed-off-by: Liam Girdwood