kernel.git/drivers/net/wireless/ti, branch linux-3.17.yHosts the 0x221E linux distro kernel.
https://git.0xinfinity.dev/distro/kernel.git/atom?h=linux-3.17.y2014-07-15T20:00:02Zwlcore/wl18xx/wl12xx: convert bitmaps to unsigned longs2014-07-15T20:00:02ZEliad Peller2014-07-11T00:01:39Zurn:sha1:5e74b3aa6ffd80128e3df605bf27d8a6a3c04997
The *_bit operations expect unsigned longs.
Instead of casting the pointers, simply define various
bitmaps as unsigned long (instead of u32).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl18xx: make sure fw_status->priv exists before deref2014-07-15T20:00:02ZEliad Peller2014-07-11T00:01:38Zurn:sha1:9bccb8ae054fda9ab51e3291eeee545ecc1f1854
In some corner cases with specific timings, we might
try dequeueing tx before we got information about
the link status (e.g. due to recovery during tx).
Instead of NULL dereference, assume all
the links in this case have low priorities.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl18xx: change the number of WLAN addrs per chip2014-07-15T20:00:01ZArik Nemtsov2014-07-11T00:01:37Zurn:sha1:1631020226ee6a95d1d9ff64562c5da1113ff77f
Each 18xx chip contains only 2 real MAC addresses
usable for WLAN, forcing us to use the LAA bit
approach to obtain a third MAC address.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlcore: don't switch channels on disconnected STA vifs2014-07-15T20:00:00ZArik Nemtsov2014-07-11T00:01:36Zurn:sha1:e65628691f04f1a9ce57d8036c9b119c43031187
Sending the FW a channel switch command on a disconnected
vif may result in a beacon loss event. Avoid this corner case.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlcore: register vendor commands2014-07-15T19:59:59ZEliad Peller2014-07-11T00:01:35Zurn:sha1:d8c5a48d2751086de9ed0ae9ff97ab094e2d534d
All the smart config code is in place now,
so register the relevant vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlcore: increase max roc duration to 30 seconds2014-07-15T19:59:58ZEliad Peller2014-07-11T00:01:34Zurn:sha1:fbddf587cbd1b75557267b674c8b42a677437c69
we don't have any actual limitation in the driver, so
increase it arbitrarily to 30 seconds.
The long ROC is needed for the smart config.flow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlcore/wl18xx: handle smart config events2014-07-15T19:59:57ZEliad Peller2014-07-11T00:01:33Zurn:sha1:e93e15fb47e53bd5dc256e2c3e40785b39ff8ff7
add defintions and handling for smart config events
(SMART_CONFIG_SYNC_EVENT_ID and SMART_CONFIG_DECODE_EVENT_ID)
parse the relevant info and send it to userspace as
vendor event.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlcore: handle smart config vendor commands2014-07-15T19:59:56ZEliad Peller2014-07-11T00:01:32Zurn:sha1:80ff8063e87c352072c6d96fb2d87becaf591966
userspace can ask to perform various smart config
actions via custom vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlcore/wl18xx: add smart config commands2014-07-15T19:59:56ZEliad Peller2014-07-11T00:01:31Zurn:sha1:ccb1df948085abcac0a91154e9cabeb563b65833
These commands configures the fw to set key,
enter smart config mode, and exit it.
Add relevant hw ops as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlcore: add smart config definitions2014-07-15T19:59:55ZEliad Peller2014-07-11T00:01:30Zurn:sha1:936c50dd0605d7d81772f53700ef42f45525ffad
Add definitions for the smart config commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>