kernel.git/drivers/net/wireless/rt2x00/rt2800lib.c, branch linux-3.5.y

rt2x00: Add debugfs access for rfcsr register

2012-05-09T01:53:46Z

RFCSR is only used in rt2800. For other chipsets, the debug struct for rfcsr should be zeroed, which isn't be an issue, since the code can now cope with that. Signed-off-by: Anisse Astier Acked-by: Ivo van Doorn Signed-off-by: John W. Linville

rt2800: add chipset revision RT5390R support

2012-04-23T19:37:42Z

About 70% of the chips with revision RT5390R initialize incorrectly, using the auxiliary antenna instead of the main one. The net result is that signal reception is very poor (no AP further than 1M). This chipset differs from RT5390 and RT5390F by its support of hardware antenna diversity. Therefore antenna selection should be done differently, by disabling software features and previously selected antenna. This changeset does just that, and makes all RT5390R work properly. This is based on Ralink's 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO driver. Signed-off-by: Anisse Astier Signed-off-by: John W. Linville

rt2800: initialize queues before giving up due to DMA error

2012-04-13T18:32:48Z

Don't immediately abort .start if DMA is busy before we initialize the queues. Some drivers do not deinitialize queues properly and we would fail to take over after them. This behaviour is consistent with legacy driver. Signed-off-by: Jakub Kicinski Acked-by: Gertjan van Wingerde Reviewed-by: Stanislaw Gruszka Signed-off-by: John W. Linville

rt2800: add disabling of DMA before loading firmware

2012-04-13T18:32:48Z

Legacy driver disables DMA before loading firmware. Signed-off-by: Jakub Kicinski Reviewed-by: Stanislaw Gruszka Acked-by: Gertjan van Wingerde Signed-off-by: John W. Linville

rt2800: introduce wpdma_disable function

2012-04-13T18:32:47Z

Introduce wpdma_disable function to simplify the code. Signed-off-by: Jakub Kicinski Reviewed-by: Stanislaw Gruszka Acked-by: Gertjan van Wingerde Signed-off-by: John W. Linville

rt2x00: Set IEEE80211_HW_REPORTS_TX_ACK_STATUS in rt2800

2012-03-15T17:40:25Z

rt2800 already reports the tx ack status of each frame back to mac80211. Advertise this by setting IEEE80211_HW_REPORTS_TX_ACK_STATUS for rt2800. This allows some mac80211 features like frame loss notifications to work with rt2800. Signed-off-by: Helmut Schaa Signed-off-by: John W. Linville

rt2x00:Add RT5372 chipset support

2012-02-27T19:06:31Z

Signed-off-by: John Li Acked-by: Gertjan van Wingerde Acked-by: Ivo van Doorn Signed-off-by: John W. Linville

rt2x00:Add VCO recalibration

2012-02-27T19:05:44Z

Signed-off-by: John Li Acked-by: Gertjan van Wingerde Acked-by: Ivo van Doorn Signed-off-by: John W. Linville

rt2x00:Add debug message for new chipset

2012-02-22T19:47:37Z

Signed-off-by: John Li Acked-by: Helmut Schaa Acked-by: Gertjan van Wingerde Acked-by: Ivo van Doorn Signed-off-by: John W. Linville

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless

2012-02-15T21:24:37Z

Conflicts: net/mac80211/debugfs_sta.c net/mac80211/sta_info.h