kernel.git/drivers/net/wireless/p54, branch linux-3.4.y

p54: clamp properly instead of just truncating

2014-03-31T04:40:30Z

commit 608cfbe4abaf76e9d732efd7ed1cfa3998163d91 upstream. The call to clamp_t() first truncates the variable signed 8 bit and as a result, the actual clamp is a no-op. Fixes: 0d78156eef1d ('p54: improve site survey') Signed-off-by: Dan Carpenter Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

p54usb: add USB ID for Corega WLUSB2GTST USB adapter

2013-10-13T22:42:49Z

commit 1e43692cdb7cc445d6347d8a5207d9cef0c71434 upstream. Added USB ID for Corega WLUSB2GTST USB adapter. Reported-by: Joerg Kalisch Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

p54usb: corrected USB ID for T-Com Sinus 154 data II

2013-02-28T14:59:02Z

commit 008e33f733ca51acb2dd9d88ea878693b04d1d2a upstream. Corrected USB ID for T-Com Sinus 154 data II. ISL3887-based. The device was tested in managed mode with no security, WEP 128 bit and WPA-PSK (TKIP) with firmware 2.13.1.0.lm87.arm (md5sum: 7d676323ac60d6e1a3b6d61e8c528248). It works. Signed-off-by: Tomasz Guszkowski Acked-By: Christian Lamparter Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

p54usb: add USBIDs for two more p54usb devices

2013-01-11T17:06:52Z

commit 4010fe21a315b4223c25376714c6a2b61b722e5c upstream. This patch adds USBIDs for: - DrayTek Vigor 530 - Zoom 4410a It also adds a note about Gemtek WUBI-100GW and SparkLAN WL-682 USBID conflict [WUBI-100GW is a ISL3886+NET2280 (LM86 firmare) solution, whereas WL-682 is a ISL3887 (LM87 firmware)] device. Source: Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

p54usb: add USB ID for T-Com Sinus 154 data II

2013-01-11T17:06:51Z

commit 3194b7fcdf6caea338b5d2c72d76fed80437649c upstream. Added USB ID for T-Com Sinus 154 data II. Signed-off-by: Tomasz Guszkowski Acked-by: Christian Lamparter Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

USB: p54usb: remove __devinit* from the struct usb_device_id table

2012-09-14T17:00:21Z

commit b9c4167cbbafddac3462134013bc15e63e4c53ef upstream. This structure needs to always stick around, even if CONFIG_HOTPLUG is disabled, otherwise we can oops when trying to probe a device that was added after the structure is thrown away. Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down. Reported-by: Fengguang Wu Reported-by: Bjørn Mork CC: Christian Lamparter CC: "John W. Linville" Signed-off-by: Greg Kroah-Hartman

p54pci: use new driver.pm interface for suspend/resume

2012-03-06T20:16:06Z

Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville

p54: pass interface setup errors back to mac80211

2012-03-06T20:16:06Z

Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville

p54spi: Release GPIO lines and IRQ on error in p54spi_probe

2012-03-05T20:23:17Z

This makes it possible to reload driver if insmod has failed due to missing firmware. Signed-off-by: Max Filippov Cc: stable Acked-by: Christian Lamparter Signed-off-by: John W. Linville

mac80211: handle non-bufferable MMPDUs correctly

2012-02-29T19:14:54Z

This renames the IEEE80211_TX_CTL_POLL_RESPONSE TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also uses it for non-bufferable MMPDUs (all MMPDUs but deauth, disassoc and action frames.) Previously, mac80211 would let the MMPDU through but not set the flag so drivers supporting some hardware aids for avoiding the PS races would then reject the frame. Signed-off-by: Johannes Berg Signed-off-by: John W. Linville