kernel.git/drivers/net/usb/catc.c, branch linux-3.12.y

catc: Use heap buffer for memory size test

2017-05-09T06:19:29Z

commit 2d6a0e9de03ee658a9adc3bfb2f0ca55dff1e478 upstream. Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller Cc: Brad Spengler Signed-off-by: Jiri Slaby

catc: Combine failure cleanup code in catc_probe()

2017-05-09T06:19:28Z

commit d41149145f98fe26dcd0bfd1d6cc095e6e041418 upstream. Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller Signed-off-by: Jiri Slaby

ethtool: fix drvinfo strings set in drivers

2013-01-07T05:06:31Z

Use strlcpy where possible to ensure the string is \0 terminated. Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN and custom defines. Use snprintf instead of sprint. Remove unnecessary inits of ->fw_version Remove unnecessary inits of drvinfo struct. Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller

USB: remove dbg() usage in USB networking drivers

2012-09-20T21:53:14Z

The dbg() USB macro is so old, it predates me. The USB networking drivers are the last hold-out using this macro, and we want to get rid of it, so replace the usage of it with the proper netdev_dbg() or dev_dbg() (depending on the context) calls. Some places we end up using a local variable for the debug call, so also convert the other existing dev_* calls to use it as well, to save tiny amounts of code space. Signed-off-by: Greg Kroah-Hartman Signed-off-by: David S. Miller

USB: Disable hub-initiated LPM for comms devices.

2012-05-18T22:42:55Z

Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp Cc: Marcel Holtmann Cc: Gustavo Padovan Cc: Johan Hedberg Cc: Hansjoerg Lipp Cc: Tilman Schmidt Cc: Karsten Keil Cc: Peter Korsgaard Cc: Jan Dumon Cc: Petko Manolov Cc: Steve Glendinning Cc: "John W. Linville" Cc: Kalle Valo Cc: "Luis R. Rodriguez" Cc: Jouni Malinen Cc: Vasanthakumar Thiagarajan Cc: Senthil Balasubramanian Cc: Christian Lamparter Cc: Brett Rudley Cc: Roland Vossen Cc: Arend van Spriel Cc: "Franky (Zhenhui) Lin" Cc: Kan Yan Cc: Dan Williams Cc: Jussi Kivilinna Cc: Ivo van Doorn Cc: Gertjan van Wingerde Cc: Helmut Schaa Cc: Herton Ronaldo Krzesinski Cc: Hin-Tak Leung Cc: Larry Finger Cc: Chaoming Li Cc: Daniel Drake Cc: Ulrich Kunitz Signed-off-by: Sarah Sharp

USB: catc.c: remove err() usage

2012-04-25T19:37:47Z

err() was a very old USB-specific macro that I thought had gone away. This patch removes it from being used in the driver and uses dev_err() instead. Signed-off-by: Greg Kroah-Hartman

USB: convert drivers/net/* to use module_usb_driver()

2011-11-18T17:44:20Z

This converts the drivers in drivers/net/* to use the module_usb_driver() macro which makes the code smaller and a bit simpler. Added bonus is that it removes some unneeded kernel log messages about drivers loading and/or unloading. Cc: Wolfgang Grandegger Cc: Samuel Ortiz Cc: Oliver Neukum Cc: Peter Korsgaard Cc: Petko Manolov Cc: Steve Glendinning Cc: Christian Lamparter Cc: "John W. Linville" Cc: Dan Williams Cc: Jussi Kivilinna Cc: Ivo van Doorn Cc: Gertjan van Wingerde Cc: Helmut Schaa Cc: Herton Ronaldo Krzesinski Cc: Hin-Tak Leung Cc: Larry Finger Cc: Chaoming Li Cc: Lucas De Marchi Cc: "David S. Miller" Cc: Roel Kluin Cc: Paul Gortmaker Cc: Jiri Pirko Cc: Pavel Roskin Cc: Yoann DI-RUZZA Cc: George Signed-off-by: Greg Kroah-Hartman

net: remove use of ndo_set_multicast_list in drivers

2011-08-18T03:22:03Z

replace it by ndo_set_rx_mode Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller

drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()

2011-05-31T22:30:17Z

catc_ctrl_run() calls usb_submit_urb() with GFP_KERNEL, while it is called from catc_ctrl_async() and catc_ctrl_done() with catc->ctrl_lock spinlock held. The patch replaces GFP_KERNEL with GFP_ATOMIC. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov Signed-off-by: David S. Miller

ethtool: cosmetic: Use ethtool ethtool_cmd_speed API

2011-04-29T21:03:01Z

This updates the network drivers so that they don't access the ethtool_cmd::speed field directly, but use ethtool_cmd_speed() instead. For most of the drivers, these changes are purely cosmetic and don't fix any problem, such as for those 1GbE/10GbE drivers that indirectly call their own ethtool get_settings()/mii_ethtool_gset(). The changes are meant to enforce code consistency and provide robustness with future larger throughputs, at the expense of a few CPU cycles for each ethtool operation. All drivers compiled with make allyesconfig ion x86_64 have been updated. Tested: make allyesconfig on x86_64 + e1000e/bnx2x work Signed-off-by: David Decotigny Signed-off-by: David S. Miller