kernel.git/drivers/net/phy/Kconfig, branch linux-3.6.y

netdev/phy: Add driver for Broadcom BCM87XX 10G Ethernet PHYs

2012-06-28T04:23:25Z

Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs which use MII_ADDR_C45 addressing. They are always 10G full duplex, so there is no autonegotiation. All we do is report link state and send interrupts when it changes. If the PHY has a device tree of_node associated with it, the "broadcom,c45-reg-init" property is used to supply register initialization values when config_init() is called. Signed-off-by: David Daney Signed-off-by: David S. Miller

netdev/of/phy: Add MDIO bus multiplexer driven by GPIO lines.

2012-05-08T02:58:09Z

The GPIO pins select which sub bus is connected to the master. Initially tested with an sn74cbtlv3253 switch device wired into the MDIO bus. Signed-off-by: David Daney Signed-off-by: David S. Miller

netdev/of/phy: Add MDIO bus multiplexer support.

2012-05-08T02:58:09Z

This patch adds a somewhat generic framework for MDIO bus multiplexers. It is modeled on the I2C multiplexer. The multiplexer is needed if there are multiple PHYs with the same address connected to the same MDIO bus adepter, or if there is insufficient electrical drive capability for all the connected PHY devices. Conceptually it could look something like this: ------------------ | Control Signal | --------+--------- | --------------- --------+------ | MDIO MASTER |---| Multiplexer | --------------- --+-------+---- | | C C h h i i l l d d | | --------- A B --------- | | | | | | | PHY@1 +-------+ +---+ PHY@1 | | | | | | | --------- | | --------- --------- | | --------- | | | | | | | PHY@2 +-------+ +---+ PHY@2 | | | | | --------- --------- This framework configures the bus topology from device tree data. The mechanics of switching the multiplexer is left to device specific drivers. The follow-on patch contains a multiplexer driven by GPIO lines. Signed-off-by: David Daney Signed-off-by: David S. Miller

phy: add am79c874 PHY support

2012-03-19T22:02:05Z

Signed-off-by: Heiko Schocher Signed-off-by: Anatolij Gustschin Signed-off-by: David S. Miller

phy: Micrel KS8995MA 5-ports 10/100 managed Ethernet switch support added

2011-12-19T21:30:40Z

Signed-off-by: Gabor Juhos Signed-off-by: Frederic Lambert Signed-off-by: David S. Miller

net: Revert ARCNET and PHYLIB to tristate options

2011-11-26T19:36:49Z

commit 88491d8103498a6166f70d5999902fec70924314 ("drivers/net: Kconfig & Makefile cleanup") changed the type of these options to bool, but they select code that could (and still can) be built as modules. Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller

drivers/net: Kconfig & Makefile cleanup

2011-08-27T07:58:49Z

The is does a general cleanup of the drivers/net/ Kconfig and Makefile. This patch create a "core" option and places all the networking core drivers into this option (default is yes for this option). In addition, it alphabitizes the Kconfig driver options. As a side cleanup, found that the arcnet, token ring, and PHY Kconfig options were a tri-state option and should have been a bool option. Signed-off-by: Jeff Kirsher

phylib: Allow BCM63XX PHY to be selected only on BCM63XX.

2011-06-17T03:45:01Z

This PHY is available integrated into BCM63xx series SOCs only. Signed-off-by: Ralf Baechle drivers/net/phy/Kconfig | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) Acked-by: Florian Fainelli Signed-off-by: David S. Miller

phy: Remove unneeded depends on PHYLIB

2011-02-12T06:01:08Z

Remove unneeded depends on PHYLIB. The config selection is already in an if PHYLIB / endif block. Signed-off-by: H Hartley Sweeten Cc: "David S. Miller" Signed-off-by: David S. Miller

phy: add the IC+ IP1001 driver

2010-12-10T23:48:43Z

This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver. I've had to add an additional delay (2ns) to adjust RX clock phase at GMII/ RGMII interface (according to the PHY data-sheet). This helps to have the RGMII working on some ST platforms. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller