kernel.git/drivers/net/ethernet/ti, branch linux-6.17.y

net: ethernet: ti: netcp: Standardize knav_dma_open_channel to return NULL on error

2025-12-01T10:46:05Z

[ Upstream commit 90a88306eb874fe4bbdd860e6c9787f5bbc588b5 ] Make knav_dma_open_channel consistently return NULL on error instead of ERR_PTR. Currently the header include/linux/soc/ti/knav_dma.h returns NULL when the driver is disabled, but the driver implementation does not even return NULL or ERR_PTR on failure, causing inconsistency in the users. This results in a crash in netcp_free_navigator_resources as followed (trimmed): Unhandled fault: alignment exception (0x221) at 0xfffffff2 [fffffff2] *pgd=80000800207003, *pmd=82ffda003, *pte=00000000 Internal error: : 221 [#1] SMP ARM Modules linked in: CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.17.0-rc7 #1 NONE Hardware name: Keystone PC is at knav_dma_close_channel+0x30/0x19c LR is at netcp_free_navigator_resources+0x2c/0x28c [... TRIM...] Call trace: knav_dma_close_channel from netcp_free_navigator_resources+0x2c/0x28c netcp_free_navigator_resources from netcp_ndo_open+0x430/0x46c netcp_ndo_open from __dev_open+0x114/0x29c __dev_open from __dev_change_flags+0x190/0x208 __dev_change_flags from netif_change_flags+0x1c/0x58 netif_change_flags from dev_change_flags+0x38/0xa0 dev_change_flags from ip_auto_config+0x2c4/0x11f0 ip_auto_config from do_one_initcall+0x58/0x200 do_one_initcall from kernel_init_freeable+0x1cc/0x238 kernel_init_freeable from kernel_init+0x1c/0x12c kernel_init from ret_from_fork+0x14/0x38 [... TRIM...] Standardize the error handling by making the function return NULL on all error conditions. The API is used in just the netcp_core.c so the impact is limited. Note, this change, in effect reverts commit 5b6cb43b4d62 ("net: ethernet: ti: netcp_core: return error while dma channel open issue"), but provides a less error prone implementation. Suggested-by: Simon Horman Suggested-by: Jacob Keller Signed-off-by: Nishanth Menon Reviewed-by: Jacob Keller Link: https://patch.msgid.link/20251103162811.3730055-1-nm@ti.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: ethernet: ti: am65-cpsw-qos: fix IET verify retry mechanism

2025-11-24T09:37:29Z

[ Upstream commit d4b00d132d7cb70a74bc039c91c1d6120943c71b ] The am65_cpsw_iet_verify_wait() function attempts verification 20 times, toggling the AM65_CPSW_PN_IET_MAC_LINKFAIL bit in each iteration. When the LINKFAIL bit transitions from 1 to 0, the MAC merge layer initiates the verification process and waits for the timeout configured in MAC_VERIFY_CNT before automatically retransmitting. The MAC_VERIFY_CNT register is configured according to the user-defined verify/response timeout in am65_cpsw_iet_set_verify_timeout_count(). As per IEEE 802.3 Clause 99, the hardware performs this automatic retry up to 3 times. Current implementation toggles LINKFAIL after the user-configured verify/response timeout in each iteration, forcing the hardware to restart verification instead of respecting the MAC_VERIFY_CNT timeout. This bypasses the hardware's automatic retry mechanism. Fix this by moving the LINKFAIL bit toggle outside the retry loop and reducing the retry count from 20 to 3. The software now only monitors the status register while the hardware autonomously handles the 3 verification attempts at proper MAC_VERIFY_CNT intervals. Fixes: 49a2eb9068246 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support") Signed-off-by: Aksh Garg Link: https://patch.msgid.link/20251106092305.1437347-3-a-garg7@ti.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: ethernet: ti: am65-cpsw-qos: fix IET verify/response timeout

2025-11-24T09:37:29Z

[ Upstream commit 49b3916465176a5abcb29a0e464825f553d55d58 ] The CPSW module uses the MAC_VERIFY_CNT bit field in the CPSW_PN_IET_VERIFY_REG_k register to set the verify/response timeout count. This register specifies the number of clock cycles to wait before resending a verify packet if the verification fails. The verify/response timeout count, as being set by the function am65_cpsw_iet_set_verify_timeout_count() is hardcoded for 125MHz clock frequency, which varies based on PHY mode and link speed. The respective clock frequencies are as follows: - RGMII mode: * 1000 Mbps: 125 MHz * 100 Mbps: 25 MHz * 10 Mbps: 2.5 MHz - QSGMII/SGMII mode: 125 MHz (all speeds) Fix this by adding logic to calculate the correct timeout counts based on the actual PHY interface mode and link speed. Fixes: 49a2eb9068246 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support") Signed-off-by: Aksh Garg Link: https://patch.msgid.link/20251106092305.1437347-2-a-garg7@ti.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: ti: icssg-prueth: Fix fdb hash size configuration

2025-11-13T20:37:44Z

[ Upstream commit ae4789affd1e181ae46e72e2b5fbe2d6d7b6616a ] The ICSSG driver does the initial FDB configuration which includes setting the control registers. Other run time management like learning is managed by the PRU's. The default FDB hash size used by the firmware is 512 slots, which is currently missing in the current driver. Update the driver FDB config to include FDB hash size as well. Please refer trm [1] 6.4.14.12.17 section on how the FDB config register gets configured. From the table 6-1404, there is a reset field for FDB_HAS_SIZE which is 4, meaning 1024 slots. Currently the driver is not updating this reset value from 4(1024 slots) to 3(512 slots). This patch fixes this by updating the reset value to 512 slots. [1]: https://www.ti.com/lit/pdf/spruim2 Fixes: abd5576b9c57f ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Meghana Malladi Reviewed-by: Simon Horman Link: https://patch.msgid.link/20251104104415.3110537-1-m-malladi@ti.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: ethernet: ti: am65-cpts: fix timestamp loss due to race conditions

2025-10-29T13:10:19Z

[ Upstream commit 49d34f3dd8519581030547eb7543a62f9ab5fa08 ] Resolve race conditions in timestamp events list handling between TX and RX paths causing missed timestamps. The current implementation uses a single events list for both TX and RX timestamps. The am65_cpts_find_ts() function acquires the lock, splices all events (TX as well as RX events) to a temporary list, and releases the lock. This function performs matching of timestamps for TX packets only. Before it acquires the lock again to put the non-TX events back to the main events list, a concurrent RX processing thread could acquire the lock (as observed in practice), find an empty events list, and fail to attach timestamp to it, even though a relevant event exists in the spliced list which is yet to be restored to the main list. Fix this by creating separate events lists to handle TX and RX timestamps independently. Fixes: c459f606f66df ("net: ethernet: ti: am65-cpts: Enable RX HW timestamp for PTP packets using CPTS FIFO") Signed-off-by: Aksh Garg Reviewed-by: Siddharth Vadapalli Link: https://patch.msgid.link/20251016115755.1123646-1-a-garg7@ti.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

hsr: hold rcu and dev lock for hsr_get_port_ndev

2025-09-11T09:49:19Z

hsr_get_port_ndev calls hsr_for_each_port, which need to hold rcu lock. On the other hand, before return the port device, we need to hold the device reference to avoid UaF in the caller function. Suggested-by: Paolo Abeni Fixes: 9c10dd8eed74 ("net: hsr: Create and export hsr_get_port_ndev()") Signed-off-by: Hangbin Liu Reviewed-by: Simon Horman Link: https://patch.msgid.link/20250905091533.377443-4-liuhangbin@gmail.com Signed-off-by: Paolo Abeni

net: ethernet: ti: am65-cpsw-nuss: Fix null pointer dereference for ndev

2025-09-02T12:51:45Z

In the TX completion packet stage of TI SoCs with CPSW2G instance, which has single external ethernet port, ndev is accessed without being initialized if no TX packets have been processed. It results into null pointer dereference, causing kernel to crash. Fix this by having a check on the number of TX packets which have been processed. Fixes: 9a369ae3d143 ("net: ethernet: ti: am65-cpsw: remove am65_cpsw_nuss_tx_compl_packets_2g()") Signed-off-by: Nishanth Menon Signed-off-by: Chintan Vankar Reviewed-by: Simon Horman Link: https://patch.msgid.link/20250829121051.2031832-1-c-vankar@ti.com Signed-off-by: Paolo Abeni

net: ti: icssg-prueth: Fix HSR and switch offload Enablement during firwmare reload.

2025-08-19T10:26:18Z

To enable HSR / Switch offload, certain configurations are needed. Currently they are done inside icssg_change_mode(). This function only gets called if we move from one mode to another without bringing the links up / down. Once in HSR / Switch mode, if we bring the links down and bring it back up again. The callback sequence is, - emac_ndo_stop() Firmwares are stopped - emac_ndo_open() Firmwares are loaded In this path icssg_change_mode() doesn't get called and as a result the configurations needed for HSR / Switch is not done. To fix this, put all these configurations in a separate function icssg_enable_fw_offload() and call this from both icssg_change_mode() and emac_ndo_open() Fixes: 56375086d093 ("net: ti: icssg-prueth: Enable HSR Tx duplication, Tx Tag and Rx Tag offload") Signed-off-by: MD Danish Anwar Link: https://patch.msgid.link/20250814105106.1491871-1-danishanwar@ti.com Signed-off-by: Paolo Abeni

net: ti: icss-iep: Fix incorrect type for return value in extts_enable()

2025-08-08T19:54:54Z

The variable ret in icss_iep_extts_enable() was incorrectly declared as u32, while the function returns int and may return negative error codes. This will cause sign extension issues and incorrect error propagation. Update ret to be int to fix error handling. This change corrects the declaration to avoid potential type mismatch. Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: Alok Tiwari Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250805142323.1949406-1-alok.a.tiwari@oracle.com Signed-off-by: Jakub Kicinski

net: ti: icssg-prueth: Fix emac link speed handling

2025-08-08T19:06:12Z

When link settings are changed emac->speed is populated by emac_adjust_link(). The link speed and other settings are then written into the DRAM. However if both ports are brought down after this and brought up again or if the operating mode is changed and a firmware reload is needed, the DRAM is cleared by icssg_config(). As a result the link settings are lost. Fix this by calling emac_adjust_link() after icssg_config(). This re populates the settings in the DRAM after a new firmware load. Fixes: 9facce84f406 ("net: ti: icssg-prueth: Fix firmware load sequence.") Signed-off-by: MD Danish Anwar Reviewed-by: Andrew Lunn Message-ID: <20250805173812.2183161-1-danishanwar@ti.com> Signed-off-by: Jakub Kicinski