kernel.git/drivers/net/ethernet/stmicro, branch master

net: stmmac: Defer VLAN HW configuration when interface is down

2026-03-05T02:48:49Z

VLAN register accesses on the MAC side require the PHY RX clock to be active. When the network interface is down, the PHY is suspended and the RX clock is unavailable, causing VLAN operations to fail with timeouts. The VLAN core automatically removes VID 0 after the interface goes down and re-adds it when it comes back up, so these timeouts happen during normal interface down/up: # ip link set end1 down renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter renesas-gbeth 15c40000.ethernet end1: failed to kill vid 0081/0 Adding VLANs while the interface is down also fails: # ip link add link end1 name end1.10 type vlan id 10 renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter RTNETLINK answers: Device or resource busy To fix this, check if the interface is up before accessing VLAN registers. The software state is always kept up to date regardless of interface state. When the interface is brought up, stmmac_vlan_restore() is called to write the VLAN state to hardware. Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering") Signed-off-by: Ovidiu Panait Link: https://patch.msgid.link/20260303145828.7845-5-ovidiu.panait.rb@renesas.com Signed-off-by: Jakub Kicinski

net: stmmac: Fix VLAN HW state restore

2026-03-05T02:48:49Z

When the network interface is opened or resumed, a DMA reset is performed, which resets all hardware state, including VLAN state. Currently, only the resume path is restoring the VLAN state via stmmac_restore_hw_vlan_rx_fltr(), but that is incomplete: the VLAN hash table and the VLAN_TAG control bits are not restored. Therefore, add stmmac_vlan_restore(), which restores the full VLAN state by updating both the HW filter entries and the hash table, and call it from both the open and resume paths. The VLAN restore is moved outside of phylink_rx_clk_stop_block/unblock in the resume path because receive clock stop is already disabled when stmmac supports VLAN. Also, remove the hash readback code in vlan_restore_hw_rx_fltr() that attempts to restore VTHM by reading VLAN_HASH_TABLE, as it always reads zero after DMA reset, making it dead code. Fixes: 3cd1cfcba26e ("net: stmmac: Implement VLAN Hash Filtering in XGMAC") Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering") Signed-off-by: Ovidiu Panait Link: https://patch.msgid.link/20260303145828.7845-4-ovidiu.panait.rb@renesas.com Signed-off-by: Jakub Kicinski

net: stmmac: Improve double VLAN handling

2026-03-05T02:48:49Z

The double VLAN bits (EDVLP, ESVL, DOVLTC) are handled inconsistently between the two vlan_update_hash() implementations: - dwxgmac2_update_vlan_hash() explicitly clears the double VLAN bits when is_double is false, meaning that adding a 802.1Q VLAN will disable double VLAN mode: $ ip link add link eth0 name eth0.200 type vlan id 200 protocol 802.1ad $ ip link add link eth0 name eth0.100 type vlan id 100 # Double VLAN bits no longer set - vlan_update_hash() sets these bits and only clears them when the last VLAN has been removed, so double VLAN mode remains enabled even after all 802.1AD VLANs are removed. Address both issues by tracking the number of active 802.1AD VLANs in priv->num_double_vlans. Pass this count to stmmac_vlan_update() so both implementations correctly set the double VLAN bits when any 802.1AD VLAN is active, and clear them only when none remain. Also update vlan_update_hash() to explicitly clear the double VLAN bits when is_double is false, matching the dwxgmac2 behavior. Signed-off-by: Ovidiu Panait Link: https://patch.msgid.link/20260303145828.7845-3-ovidiu.panait.rb@renesas.com Signed-off-by: Jakub Kicinski

net: stmmac: Fix error handling in VLAN add and delete paths

2026-03-05T02:48:48Z

stmmac_vlan_rx_add_vid() updates active_vlans and the VLAN hash register before writing the HW filter entry. If the filter write fails, it leaves a stale VID in active_vlans and the hash register. stmmac_vlan_rx_kill_vid() has the reverse problem: it clears active_vlans before removing the HW filter. On failure, the VID is gone from active_vlans but still present in the HW filter table. To fix this, reorder the operations to update the hash table first, then attempt the HW filter operation. If the HW filter fails, roll back both the active_vlans bitmap and the hash table by calling stmmac_vlan_update() again. Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering") Signed-off-by: Ovidiu Panait Link: https://patch.msgid.link/20260303145828.7845-2-ovidiu.panait.rb@renesas.com Signed-off-by: Jakub Kicinski

Merge tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2026-02-26T16:00:13Z

Pull networking fixes from Paolo Abeni: "Including fixes from IPsec, Bluetooth and netfilter Current release - regressions: - wifi: fix dev_alloc_name() return value check - rds: fix recursive lock in rds_tcp_conn_slots_available Current release - new code bugs: - vsock: lock down child_ns_mode as write-once Previous releases - regressions: - core: - do not pass flow_id to set_rps_cpu() - consume xmit errors of GSO frames - netconsole: avoid OOB reads, msg is not nul-terminated - netfilter: h323: fix OOB read in decode_choice() - tcp: re-enable acceptance of FIN packets when RWIN is 0 - udplite: fix null-ptr-deref in __udp_enqueue_schedule_skb(). - wifi: brcmfmac: fix potential kernel oops when probe fails - phy: register phy led_triggers during probe to avoid AB-BA deadlock - eth: - bnxt_en: fix deleting of Ntuple filters - wan: farsync: fix use-after-free bugs caused by unfinished tasklets - xscale: check for PTP support properly Previous releases - always broken: - tcp: fix potential race in tcp_v6_syn_recv_sock() - kcm: fix zero-frag skb in frag_list on partial sendmsg error - xfrm: - fix race condition in espintcp_close() - always flush state and policy upon NETDEV_UNREGISTER event - bluetooth: - purge error queues in socket destructors - fix response to L2CAP_ECRED_CONN_REQ - eth: - mlx5: - fix circular locking dependency in dump - fix "scheduling while atomic" in IPsec MAC address query - gve: fix incorrect buffer cleanup for QPL - team: avoid NETDEV_CHANGEMTU event when unregistering slave - usb: validate USB endpoints" * tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits) netfilter: nf_conntrack_h323: fix OOB read in decode_choice() dpaa2-switch: validate num_ifs to prevent out-of-bounds write net: consume xmit errors of GSO frames vsock: document write-once behavior of the child_ns_mode sysctl vsock: lock down child_ns_mode as write-once selftests/vsock: change tests to respect write-once child ns mode net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query net/mlx5: Fix missing devlink lock in SRIOV enable error path net/mlx5: E-switch, Clear legacy flag when moving to switchdev net/mlx5: LAG, disable MPESW in lag_disable_change() net/mlx5: DR, Fix circular locking dependency in dump selftests: team: Add a reference count leak test team: avoid NETDEV_CHANGEMTU event when unregistering slave net: mana: Fix double destroy_workqueue on service rescan PCI path MAINTAINERS: Update maintainer entry for QUALCOMM ETHQOS ETHERNET DRIVER dpll: zl3073x: Remove redundant cleanup in devm_dpll_init() selftests/net: packetdrill: Verify acceptance of FIN packets when RWIN is 0 tcp: re-enable acceptance of FIN packets when RWIN is 0 vsock: Use container_of() to get net namespace in sysctl handlers net: usb: kaweth: validate USB endpoints ...

net: stmmac: fix timestamping configuration after suspend/resume

2026-02-25T01:46:15Z

When stmmac_init_timestamping() is called, it clears the receive and transmit path booleans that allow timestamps to be read. These are never re-initialised until after userspace requests timestamping features to be enabled. However, our copy of the timestamp configuration is not cleared, which means we return the old configuration to userspace when requested. This is inconsistent. Fix this by clearing the timestamp configuration. Fixes: d6228b7cdd6e ("net: stmmac: implement the SIOCGHWTSTAMP ioctl") Signed-off-by: Russell King (Oracle) Reviewed-by: Simon Horman Link: https://patch.msgid.link/E1vuUu4-0000000Afea-0j9B@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski

Convert remaining multi-line kmalloc_obj/flex GFP_KERNEL uses

2026-02-22T16:26:33Z

Conversion performed via this Coccinelle script: // SPDX-License-Identifier: GPL-2.0-only // Options: --include-headers-for-types --all-includes --include-headers --keep-comments virtual patch @gfp depends on patch && !(file in "tools") && !(file in "samples")@ identifier ALLOC = {kmalloc_obj,kmalloc_objs,kmalloc_flex, kzalloc_obj,kzalloc_objs,kzalloc_flex, kvmalloc_obj,kvmalloc_objs,kvmalloc_flex, kvzalloc_obj,kvzalloc_objs,kvzalloc_flex}; @@ ALLOC(... - , GFP_KERNEL ) $ make coccicheck MODE=patch COCCI=gfp.cocci Build and boot tested x86_64 with Fedora 42's GCC and Clang: Linux version 6.19.0+ (user@host) (gcc (GCC) 15.2.1 20260123 (Red Hat 15.2.1-7), GNU ld version 2.44-12.fc42) #1 SMP PREEMPT_DYNAMIC 1970-01-01 Linux version 6.19.0+ (user@host) (clang version 20.1.8 (Fedora 20.1.8-4.fc42), LLD 20.1.8) #1 SMP PREEMPT_DYNAMIC 1970-01-01 Signed-off-by: Kees Cook Signed-off-by: Linus Torvalds

Convert more 'alloc_obj' cases to default GFP_KERNEL arguments

2026-02-22T04:03:00Z

This converts some of the visually simpler cases that have been split over multiple lines. I only did the ones that are easy to verify the resulting diff by having just that final GFP_KERNEL argument on the next line. Somebody should probably do a proper coccinelle script for this, but for me the trivial script actually resulted in an assertion failure in the middle of the script. I probably had made it a bit _too_ trivial. So after fighting that far a while I decided to just do some of the syntactically simpler cases with variations of the previous 'sed' scripts. The more syntactically complex multi-line cases would mostly really want whitespace cleanup anyway. Signed-off-by: Linus Torvalds

Convert 'alloc_flex' family to use the new default GFP_KERNEL argument

2026-02-22T01:09:51Z

This is the exact same thing as the 'alloc_obj()' version, only much smaller because there are a lot fewer users of the *alloc_flex() interface. As with alloc_obj() version, this was done entirely with mindless brute force, using the same script, except using 'flex' in the pattern rather than 'objs*'. Signed-off-by: Linus Torvalds

Convert 'alloc_obj' family to use the new default GFP_KERNEL argument

2026-02-22T01:09:51Z

This was done entirely with mindless brute force, using git grep -l '\