kernel.git/drivers/net/ethernet/stmicro, branch linux-5.8.y

net: stmmac: use netif_tx_start|stop_all_queues() function

2020-10-29T09:07:38Z

[ Upstream commit 9f19306d166688a73356aa636c62e698bf2063cc ] The current implementation of stmmac_stop_all_queues() and stmmac_start_all_queues() will not work correctly when the value of tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command. Also, netif_tx_start|stop_all_queues() are only needed in driver open() and close() only. Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism Signed-off-by: Ong Boon Leong Signed-off-by: Voon Weifeng Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: stmmac: Fix incorrect location to set real_num_rx|tx_queues

2020-10-29T09:07:38Z

[ Upstream commit 686cff3d7022ddf35d7e38bc80191eb92de5989a ] netif_set_real_num_tx_queues() & netif_set_real_num_rx_queues() should be used to inform network stack about the real Tx & Rx queue (active) number in both stmmac_open() and stmmac_resume(), therefore, we move the code from stmmac_dvr_probe() to stmmac_hw_setup(). Fixes: c02b7a914551 net: stmmac: use netif_set_real_num_{rx,tx}_queues Signed-off-by: Aashish Verma Signed-off-by: Ong Boon Leong Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: stmmac: Modify configuration method of EEE timers

2020-10-14T09:55:57Z

[ Upstream commit 388e201d41fa1ed8f2dce0f0567f56f8e919ffb0 ] Ethtool manual stated that the tx-timer is the "the amount of time the device should stay in idle mode prior to asserting its Tx LPI". The previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW timer duration which is not correct. Hence, this patch fixes the "ethtool --set-eee tx-timer" to configure the EEE LPI timer. The LPI TW Timer will be using the defined default value instead of "ethtool --set-eee tx-timer" which follows the EEE LS timer implementation. Changelog V2 *Not removing/modifying the eee_timer. *EEE LPI timer can be configured through ethtool and also the eee_timer module param. *EEE TW Timer will be configured with default value only, not able to be configured through ethtool or module param. This follows the implementation of the EEE LS Timer. Fixes: d765955d2ae0 ("stmmac: add the Energy Efficient Ethernet support") Signed-off-by: Vineetha G. Jaya Kumaran Signed-off-by: Voon Weifeng Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: stmmac: Fix clock handling on remove path

2020-10-14T09:55:53Z

[ Upstream commit ac322f86b56cb99d1c4224c209095aa67647c967 ] While unloading the dwmac-intel driver, clk_disable_unprepare() is being called twice in stmmac_dvr_remove() and intel_eth_pci_remove(). This causes kernel panic on the second call. Removing the second call of clk_disable_unprepare() in intel_eth_pci_remove(). Fixes: 09f012e64e4b ("stmmac: intel: Fix clock handling on error and remove paths") Cc: Andy Shevchenko Reviewed-by: Voon Weifeng Signed-off-by: Wong Vee Khee Reviewed-by: Andy Shevchenko Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: stmmac: removed enabling eee in EEE set callback

2020-10-14T09:55:52Z

[ Upstream commit 7241c5a697479c7d0c5a96595822cdab750d41ae ] EEE should be only be enabled during stmmac_mac_link_up() when the link are up and being set up properly. set_eee should only do settings configuration and disabling the eee. Without this fix, turning on EEE using ethtool will return "Operation not supported". This is due to the driver is in a dead loop waiting for eee to be advertised in the for eee to be activated but the driver will only configure the EEE advertisement after the eee is activated. Ethtool should only return "Operation not supported" if there is no EEE capbility in the MAC controller. Fixes: 8a7493e58ad6 ("net: stmmac: Fix a race in EEE enable callback") Signed-off-by: Voon Weifeng Acked-by: Mark Gross Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: stmmac: dwmac1000: provide multicast filter fallback

2020-08-21T11:14:54Z

commit 592d751c1e174df5ff219946908b005eb48934b3 upstream. If we don't have a hardware multicast filter available then instead of silently failing to listen for the requested ethernet broadcast addresses fall back to receiving all multicast packets, in a similar fashion to other drivers with no multicast filter. Cc: stable@vger.kernel.org Signed-off-by: Jonathan McDowell Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: ethernet: stmmac: Disable hardware multicast filter

2020-08-21T11:14:54Z

commit df43dd526e6609769ae513a81443c7aa727c8ca3 upstream. The IPQ806x does not appear to have a functional multicast ethernet address filter. This was observed as a failure to correctly receive IPv6 packets on a LAN to the all stations address. Checking the vendor driver shows that it does not attempt to enable the multicast filter and instead falls back to receiving all multicast packets, internally setting ALLMULTI. Use the new fallback support in the dwmac1000 driver to correctly achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6 functionality on an RB3011 router. Cc: stable@vger.kernel.org Signed-off-by: Jonathan McDowell Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

treewide: replace '---help---' in Kconfig files with 'help'

2020-06-13T16:57:21Z

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada

net: ethernet: dwmac: Fix an error code in imx_dwmac_probe()

2020-06-04T22:51:25Z

The code is return PTR_ERR(NULL) which is zero or success. We should return -ENOMEM instead. Fixes: 94abdad6974a5 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip") Signed-off-by: Dan Carpenter Acked-by: Fugang Duan Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2020-06-01T00:48:46Z

xdp_umem.c had overlapping changes between the 64-bit math fix for the calculation of npgs and the removal of the zerocopy memory type which got rid of the chunk_size_nohdr member. The mlx5 Kconfig conflict is a case where we just take the net-next copy of the Kconfig entry dependency as it takes on the ESWITCH dependency by one level of indirection which is what the 'net' conflicting change is trying to ensure. Signed-off-by: David S. Miller