kernel.git/drivers/net/ethernet/stmicro, branch linux-5.7.y

net: stmmac: dwmac1000: provide multicast filter fallback

2020-08-21T11:07:24Z

commit 592d751c1e174df5ff219946908b005eb48934b3 upstream. If we don't have a hardware multicast filter available then instead of silently failing to listen for the requested ethernet broadcast addresses fall back to receiving all multicast packets, in a similar fashion to other drivers with no multicast filter. Cc: stable@vger.kernel.org Signed-off-by: Jonathan McDowell Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: ethernet: stmmac: Disable hardware multicast filter

2020-08-21T11:07:24Z

commit df43dd526e6609769ae513a81443c7aa727c8ca3 upstream. The IPQ806x does not appear to have a functional multicast ethernet address filter. This was observed as a failure to correctly receive IPv6 packets on a LAN to the all stations address. Checking the vendor driver shows that it does not attempt to enable the multicast filter and instead falls back to receiving all multicast packets, internally setting ALLMULTI. Use the new fallback support in the dwmac1000 driver to correctly achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6 functionality on an RB3011 router. Cc: stable@vger.kernel.org Signed-off-by: Jonathan McDowell Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

stmmac: intel: Fix clock handling on error and remove paths

2020-06-22T07:32:36Z

[ Upstream commit 09f012e64e4b8126ed6f02d0a85a57c3a0465cf9 ] clk_prepare_enable() might fail, we have to check its returned value. Besides that we have to call clk_disable_unprepare() on the error and remove paths. Do above in the dwmac-intel driver. While at it, remove leftover in stmmac_pci and remove unneeded condition for NULL-aware clk_unregister_fixed_rate() call. Fixes: 58da0cfa6cf1 ("net: stmmac: create dwmac-intel.c to contain all Intel platform") Cc: Voon Weifeng Signed-off-by: Andy Shevchenko Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a

2020-05-26T23:27:41Z

For rx filter 'HWTSTAMP_FILTER_PTP_V2_EVENT', it should be PTP v2/802.AS1, any layer, any kind of event packet, but HW only take timestamp snapshot for below PTP message: sync, Pdelay_req, Pdelay_resp. Then it causes below issue when test E2E case: ptp4l[2479.534]: port 1: received DELAY_REQ without timestamp ptp4l[2481.423]: port 1: received DELAY_REQ without timestamp ptp4l[2481.758]: port 1: received DELAY_REQ without timestamp ptp4l[2483.524]: port 1: received DELAY_REQ without timestamp ptp4l[2484.233]: port 1: received DELAY_REQ without timestamp ptp4l[2485.750]: port 1: received DELAY_REQ without timestamp ptp4l[2486.888]: port 1: received DELAY_REQ without timestamp ptp4l[2487.265]: port 1: received DELAY_REQ without timestamp ptp4l[2487.316]: port 1: received DELAY_REQ without timestamp Timestamp snapshot dependency on register bits in received path: SNAPTYPSEL TSMSTRENA TSEVNTENA PTP_Messages 01 x 0 SYNC, Follow_Up, Delay_Req, Delay_Resp, Pdelay_Req, Pdelay_Resp, Pdelay_Resp_Follow_Up 01 0 1 SYNC, Pdelay_Req, Pdelay_Resp For dwmac v5.10a, enabling all events by setting register DWC_EQOS_TIME_STAMPING[SNAPTYPSEL] to 2’b01, clearing bit [TSEVNTENA] to 0’b0, which can support all required events. Signed-off-by: Fugang Duan Signed-off-by: David S. Miller

net: stmmac: don't attach interface until resume finishes

2020-05-23T23:30:27Z

Commit 14b41a2959fb ("net: stmmac: Delete txtimer in suspend") was the first attempt to fix a race between mod_timer() and setup_timer() during stmmac_resume(). However the issue still exists as the commit only addressed half of the issue. Same race can still happen as stmmac_resume() re-attaches interface way too early - even before hardware is fully initialized. Worse, doing so allows network traffic to restart and stmmac_tx_timer_arm() being called in the middle of stmmac_resume(), which re-init tx timers in stmmac_init_coalesce(). timer_list will be corrupted and system crashes as a result of race between mod_timer() and setup_timer(). systemd--1995 2.... 552950018us : stmmac_suspend: 4994 ksoftirq-9 0..s2 553123133us : stmmac_tx_timer_arm: 2276 systemd--1995 0.... 553127896us : stmmac_resume: 5101 systemd--320 7...2 553132752us : stmmac_tx_timer_arm: 2276 (sd-exec-1999 5...2 553135204us : stmmac_tx_timer_arm: 2276 --------------------------------- pc : run_timer_softirq+0x468/0x5e0 lr : run_timer_softirq+0x570/0x5e0 Call trace: run_timer_softirq+0x468/0x5e0 __do_softirq+0x124/0x398 irq_exit+0xd8/0xe0 __handle_domain_irq+0x6c/0xc0 gic_handle_irq+0x60/0xb0 el1_irq+0xb8/0x180 arch_cpu_idle+0x38/0x230 default_idle_call+0x24/0x3c do_idle+0x1e0/0x2b8 cpu_startup_entry+0x28/0x48 secondary_start_kernel+0x1b4/0x208 Fix this by deferring netif_device_attach() to the end of stmmac_resume(). Signed-off-by: Leon Yu Signed-off-by: David S. Miller

net: ethernet: stmmac: Enable interface clocks on probe for IPQ806x

2020-05-22T23:07:02Z

The ipq806x_gmac_probe() function enables the PTP clock but not the appropriate interface clocks. This means that if the bootloader hasn't done so attempting to bring up the interface will fail with an error like: [ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma [ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed [ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed This patch, a slightly cleaned up version of one posted by Sergey Sergeev in: https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257 correctly enables the clock; we have already configured the source just before this. Tested on a MikroTik RB3011. Signed-off-by: Jonathan McDowell Signed-off-by: David S. Miller

net: stmmac: fix num_por initialization

2020-05-14T19:48:15Z

Driver missed initializing num_por which is one of the por values that driver configures to hardware. In order to get these values, add a new structure ethqos_emac_driver_data which holds por and num_por values and populate that in driver probe. Fixes: a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos") Reported-by: Rahul Ankushrao Kawadgave Signed-off-by: Vinod Koul Reviewed-by: Amit Kucheria Signed-off-by: David S. Miller

net: stmmac: gmac5+: fix potential integer overflow on 32 bit multiply

2020-05-04T18:57:21Z

The multiplication of cfg->ctr[1] by 1000000000 is performed using a 32 bit multiplication (since cfg->ctr[1] is a u32) and this can lead to a potential overflow. Fix this by making the constant a ULL to ensure a 64 bit multiply occurs. Fixes: 504723af0d85 ("net: stmmac: Add basic EST support for GMAC5+") Addresses-Coverity: ("Unintentional integer overflow") Signed-off-by: Colin Ian King Signed-off-by: David S. Miller

stmmac: fix pointer check after utilization in stmmac_interrupt

2020-05-04T17:33:53Z

The paranoidal pointer check in IRQ handler looks very strange - it really protects us only against bogus drivers which request IRQ line with null pointer dev_id. However, the code fragment is incorrect because the dev pointer is used before the actual check which leads to undefined behavior. Remove the check to avoid confusing people with incorrect code. Signed-off-by: Maxim Petrov Signed-off-by: David S. Miller

stmmac: intel: Fix kernel crash due to wrong error path

2020-05-01T04:00:17Z

Unfortunately sometimes ->probe() may fail. The commit b9663b7ca6ff ("net: stmmac: Enable SERDES power up/down sequence") messed up with error handling and thus: [ 12.811311] ------------[ cut here ]------------ [ 12.811993] kernel BUG at net/core/dev.c:9937! Fix this by properly crafted error path. Fixes: b9663b7ca6ff ("net: stmmac: Enable SERDES power up/down sequence") Cc: Voon Weifeng Cc: Ong Boon Leong Signed-off-by: Andy Shevchenko Signed-off-by: David S. Miller