kernel.git/drivers/net/ethernet/micrel, branch linux-5.5.y

net: ks8851-ml: Fix IO operations, again

2020-04-02T13:09:52Z

commit 8262e6f9b1034ede34548a04dec4c302d92c9497 upstream. This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it turns out these were only necessary due to buggy hardware. This patch adds a check for such a buggy hardware to prevent any such mistakes again. While working further on the KS8851 driver, it came to light that the KS8851-16MLL is capable of switching bus endianness by a hardware strap, EESK pin. If this strap is incorrect, the IO accesses require such endian swapping as is being reverted by this patch. Such swapping also impacts the performance significantly. Hence, in addition to removing it, detect that the hardware is broken, report to user, and fail to bind with such hardware. Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by: Marek Vasut Cc: David S. Miller Cc: Lukas Wunner Cc: Petr Stetiar Cc: YueHaibing Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: ks8851-ml: Fix IRQ handling and locking

2020-03-21T07:15:45Z

[ Upstream commit 44343418d0f2f623cb9da6f5000df793131cbe3b ] The KS8851 requires that packet RX and TX are mutually exclusive. Currently, the driver hopes to achieve this by disabling interrupt from the card by writing the card registers and by disabling the interrupt on the interrupt controller. This however is racy on SMP. Replace this approach by expanding the spinlock used around the ks_start_xmit() TX path to ks_irq() RX path to assure true mutual exclusion and remove the interrupt enabling/disabling, which is now not needed anymore. Furthermore, disable interrupts also in ks_net_stop(), which was missing before. Note that a massive improvement here would be to re-use the KS8851 driver approach, which is to move the TX path into a worker thread, interrupt handling to threaded interrupt, and synchronize everything with mutexes, but that would be a much bigger rework, for a separate patch. Signed-off-by: Marek Vasut Cc: David S. Miller Cc: Lukas Wunner Cc: Petr Stetiar Cc: YueHaibing Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: ks8851-ml: Fix 16-bit IO operation

2020-03-12T06:18:26Z

[ Upstream commit 58292104832fef6cb4a89f736012c0e0724c3442 ] The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that BE[3:0] signals are active high. This contradicts the measurements of the behavior of the actual chip, where these signals behave as active low. For example, to read the CIDER register, the bus must expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100. Signed-off-by: Marek Vasut Cc: David S. Miller Cc: Lukas Wunner Cc: Petr Stetiar Cc: YueHaibing Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: ks8851-ml: Fix 16-bit data access

2020-03-12T06:18:26Z

[ Upstream commit edacb098ea9c31589276152f09b4439052c0f2b1 ] The packet data written to and read from Micrel KSZ8851-16MLLI must be byte-swapped in 16-bit mode, add this byte-swapping. Signed-off-by: Marek Vasut Cc: David S. Miller Cc: Lukas Wunner Cc: Petr Stetiar Cc: YueHaibing Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: ks8851-ml: Remove 8-bit bus accessors

2020-03-12T06:18:26Z

[ Upstream commit 69233bba6543a37755158ca3382765387b8078df ] This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown, however the speculation is that this was some sort of attempt to support the 8-bit bus mode. As per the KS8851-16MLL documentation, all two registers accessed via the 8-bit accessors are internally 16-bit registers, so reading them using 16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read outright, as it is already a concatenation of two 8-bit reads of that register. The KS_RXQCR accesses are 8-bit only, however writing the top 8 bits of the register is OK as well, since the driver caches the entire 16-bit register value anyway. Finally, the driver is not used by any hardware in the kernel right now. The only hardware available to me is one with 16-bit bus, so I have no way to test the 8-bit bus mode, however it is unlikely this ever really worked anyway. If the 8-bit bus mode is ever required, it can be easily added by adjusting the 16-bit accessors to do 2 consecutive accesses, which is how this should have been done from the beginning. Signed-off-by: Marek Vasut Cc: David S. Miller Cc: Lukas Wunner Cc: Petr Stetiar Cc: YueHaibing Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

2019-09-18T19:34:53Z

Pull networking updates from David Miller: 1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski. 2) Use bio_vec in the networking instead of custom skb_frag_t, from Matthew Wilcox. 3) Make use of xmit_more in r8169 driver, from Heiner Kallweit. 4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen. 5) Support all variants of 5750X bnxt_en chips, from Michael Chan. 6) More RTNL avoidance work in the core and mlx5 driver, from Vlad Buslov. 7) Add TCP syn cookies bpf helper, from Petar Penkov. 8) Add 'nettest' to selftests and use it, from David Ahern. 9) Add extack support to drop_monitor, add packet alert mode and support for HW drops, from Ido Schimmel. 10) Add VLAN offload to stmmac, from Jose Abreu. 11) Lots of devm_platform_ioremap_resource() conversions, from YueHaibing. 12) Add IONIC driver, from Shannon Nelson. 13) Several kTLS cleanups, from Jakub Kicinski. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits) mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer mlxsw: spectrum: Register CPU port with devlink mlxsw: spectrum_buffers: Prevent changing CPU port's configuration net: ena: fix incorrect update of intr_delay_resolution net: ena: fix retrieval of nonadaptive interrupt moderation intervals net: ena: fix update of interrupt moderation register net: ena: remove all old adaptive rx interrupt moderation code from ena_com net: ena: remove ena_restore_ethtool_params() and relevant fields net: ena: remove old adaptive interrupt moderation code from ena_netdev net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*() net: ena: enable the interrupt_moderation in driver_supported_features net: ena: reimplement set/get_coalesce() net: ena: switch to dim algorithm for rx adaptive interrupt moderation net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable ethtool: implement Energy Detect Powerdown support via phy-tunable xen-netfront: do not assume sk_buff_head list is empty in error handling s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb” net: ena: don't wake up tx queue when down drop_monitor: Better sanitize notified packets ...

ethernet: micrel: Use DIV_ROUND_CLOSEST directly to make it readable

2019-09-07T15:17:02Z

The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d but is perhaps more readable. Signed-off-by: zhong jiang Signed-off-by: David S. Miller

net: remove ks8695 driver

2019-09-04T15:57:43Z

The platform is getting removed, so there are no remaining users of this driver. Link: https://lore.kernel.org/r/20190809202749.742267-6-arnd@arndb.de Signed-off-by: Arnd Bergmann

ethernet: Delete unnecessary checks before the macro call “dev_kfree_skb”

2019-08-22T23:22:04Z

The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring Signed-off-by: David S. Miller

net: ks8851-ml: use devm_platform_ioremap_resource() to simplify code

2019-08-21T20:42:12Z

Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Reported-by: Hulk Robot Signed-off-by: YueHaibing Signed-off-by: David S. Miller