kernel.git/drivers/net/ethernet/intel/igc, branch linux-5.8.y

igc: Fix not considering the TX delay for timestamps

2020-10-01T15:36:28Z

[ Upstream commit 4406e977a4a1e997818b6d77c3218ef8d15b2abf ] When timestamping a packet there's a delay between the start of the packet and the point where the hardware actually captures the timestamp. This difference needs to be considered if we want accurate timestamps. This was done on the RX side, but not on the TX side. Fixes: 2c344ae24501 ("igc: Add support for TX timestamping") Signed-off-by: Vinicius Costa Gomes Tested-by: Aaron Brown Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

igc: Fix wrong timestamp latency numbers

2020-10-01T15:36:28Z

[ Upstream commit f03369b9bfab8e23ac28ca7ab7e6631c374b7cbe ] The previous timestamping latency numbers were obtained by interpolating the i210 numbers with the i225 crystal clock value. That calculation was wrong. Use the correct values from real measurements. Fixes: 81b055205e8b ("igc: Add support for RX timestamping") Signed-off-by: Vinicius Costa Gomes Tested-by: Aaron Brown Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

igc: Fix PTP initialization

2020-08-26T09:49:10Z

[ Upstream commit 3cda505a679ced78d69c889cfb418d1728bb2707 ] Right now, igc_ptp_reset() is called from igc_reset(), which is called from igc_probe() before igc_ptp_init() has a chance to run. It is detected as an attempt to use an spinlock without registering its key first. See log below. To avoid this problem, simplify the initialization: igc_ptp_init() is only called from igc_probe(), and igc_ptp_reset() is only called from igc_reset(). [ 2.736332] INFO: trying to register non-static key. [ 2.736902] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input10 [ 2.737513] the code is fine but needs lockdep annotation. [ 2.737513] turning off the locking correctness validator. [ 2.737515] CPU: 8 PID: 239 Comm: systemd-udevd Tainted: G E 5.8.0-rc7+ #13 [ 2.737515] Hardware name: Gigabyte Technology Co., Ltd. Z390 AORUS ULTRA/Z390 AORUS ULTRA-CF, BIOS F7 03/14/2019 [ 2.737516] Call Trace: [ 2.737521] dump_stack+0x78/0xa0 [ 2.737524] register_lock_class+0x6b1/0x6f0 [ 2.737526] ? lockdep_hardirqs_on_prepare+0xca/0x160 [ 2.739177] ? _raw_spin_unlock_irq+0x24/0x50 [ 2.739179] ? trace_hardirqs_on+0x1c/0xf0 [ 2.740820] __lock_acquire+0x56/0x1ff0 [ 2.740823] ? __schedule+0x30c/0x970 [ 2.740825] lock_acquire+0x97/0x3e0 [ 2.740830] ? igc_ptp_reset+0x35/0xf0 [igc] [ 2.740833] ? schedule_hrtimeout_range_clock+0xb7/0x120 [ 2.742507] _raw_spin_lock_irqsave+0x3a/0x50 [ 2.742512] ? igc_ptp_reset+0x35/0xf0 [igc] [ 2.742515] igc_ptp_reset+0x35/0xf0 [igc] [ 2.742519] igc_reset+0x96/0xd0 [igc] [ 2.744148] igc_probe+0x68f/0x7d0 [igc] [ 2.745796] local_pci_probe+0x3d/0x70 [ 2.745799] pci_device_probe+0xd1/0x190 [ 2.745802] really_probe+0x15a/0x3f0 [ 2.759936] driver_probe_device+0xe1/0x150 [ 2.759937] device_driver_attach+0xa8/0xb0 [ 2.761786] __driver_attach+0x89/0x150 [ 2.761786] ? device_driver_attach+0xb0/0xb0 [ 2.761787] ? device_driver_attach+0xb0/0xb0 [ 2.761788] bus_for_each_dev+0x66/0x90 [ 2.765012] bus_add_driver+0x12e/0x1f0 [ 2.765716] driver_register+0x8b/0xe0 [ 2.766418] ? 0xffffffffc0230000 [ 2.767119] do_one_initcall+0x5a/0x310 [ 2.767826] ? kmem_cache_alloc_trace+0xe9/0x200 [ 2.768528] do_init_module+0x5c/0x260 [ 2.769206] __do_sys_finit_module+0x93/0xe0 [ 2.770048] do_syscall_64+0x46/0xa0 [ 2.770716] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 2.771396] RIP: 0033:0x7f83534589e0 [ 2.772073] Code: 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 2e 2e 2e 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 80 24 0d 00 f7 d8 64 89 01 48 [ 2.772074] RSP: 002b:00007ffd31d0ed18 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 2.774854] RAX: ffffffffffffffda RBX: 000055d52816aba0 RCX: 00007f83534589e0 [ 2.774855] RDX: 0000000000000000 RSI: 00007f83535b982f RDI: 0000000000000006 [ 2.774855] RBP: 00007ffd31d0ed60 R08: 0000000000000000 R09: 00007ffd31d0ed30 [ 2.774856] R10: 0000000000000006 R11: 0000000000000246 R12: 0000000000000000 [ 2.774856] R13: 0000000000020000 R14: 00007f83535b982f R15: 000055d527f5e120 Fixes: 5f2958052c58 ("igc: Add basic skeleton for PTP") Signed-off-by: Vinicius Costa Gomes Reviewed-by: Andre Guedes Tested-by: Aaron Brown Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

2020-06-03T23:27:18Z

Pull networking updates from David Miller: 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz Augusto von Dentz. 2) Add GSO partial support to igc, from Sasha Neftin. 3) Several cleanups and improvements to r8169 from Heiner Kallweit. 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a device self-test. From Andrew Lunn. 5) Start moving away from custom driver versions, use the globally defined kernel version instead, from Leon Romanovsky. 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin. 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet. 8) Add sriov and vf support to hinic, from Luo bin. 9) Support Media Redundancy Protocol (MRP) in the bridging code, from Horatiu Vultur. 10) Support netmap in the nft_nat code, from Pablo Neira Ayuso. 11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina Dubroca. Also add ipv6 support for espintcp. 12) Lots of ReST conversions of the networking documentation, from Mauro Carvalho Chehab. 13) Support configuration of ethtool rxnfc flows in bcmgenet driver, from Doug Berger. 14) Allow to dump cgroup id and filter by it in inet_diag code, from Dmitry Yakunin. 15) Add infrastructure to export netlink attribute policies to userspace, from Johannes Berg. 16) Several optimizations to sch_fq scheduler, from Eric Dumazet. 17) Fallback to the default qdisc if qdisc init fails because otherwise a packet scheduler init failure will make a device inoperative. From Jesper Dangaard Brouer. 18) Several RISCV bpf jit optimizations, from Luke Nelson. 19) Correct the return type of the ->ndo_start_xmit() method in several drivers, it's netdev_tx_t but many drivers were using 'int'. From Yunjian Wang. 20) Add an ethtool interface for PHY master/slave config, from Oleksij Rempel. 21) Add BPF iterators, from Yonghang Song. 22) Add cable test infrastructure, including ethool interfaces, from Andrew Lunn. Marvell PHY driver is the first to support this facility. 23) Remove zero-length arrays all over, from Gustavo A. R. Silva. 24) Calculate and maintain an explicit frame size in XDP, from Jesper Dangaard Brouer. 25) Add CAP_BPF, from Alexei Starovoitov. 26) Support terse dumps in the packet scheduler, from Vlad Buslov. 27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei. 28) Add devm_register_netdev(), from Bartosz Golaszewski. 29) Minimize qdisc resets, from Cong Wang. 30) Get rid of kernel_getsockopt and kernel_setsockopt in order to eliminate set_fs/get_fs calls. From Christoph Hellwig. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits) selftests: net: ip_defrag: ignore EPERM net_failover: fixed rollback in net_failover_open() Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv" Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv" vmxnet3: allow rx flow hash ops only when rss is enabled hinic: add set_channels ethtool_ops support selftests/bpf: Add a default $(CXX) value tools/bpf: Don't use $(COMPILE.c) bpf, selftests: Use bpf_probe_read_kernel s390/bpf: Use bcr 0,%0 as tail call nop filler s390/bpf: Maintain 8-byte stack alignment selftests/bpf: Fix verifier test selftests/bpf: Fix sample_cnt shared between two threads bpf, selftests: Adapt cls_redirect to call csum_level helper bpf: Add csum_level helper for fixing up csum levels bpf: Fix up bpf_skb_adjust_room helper's skb csum setting sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf() crypto/chtls: IPv6 support for inline TLS Crypto/chcr: Fixes a coccinile check error Crypto/chcr: Fixes compilations warnings ...

igc: Fix wrong register name

2020-05-29T03:33:53Z

Accordance to the i225 datasheet this register address used by Host Transmit Discarded Packet by MAC counter and not by not applicable Carrier Extension Error counter. This patch comes to fix this wrong definition. Signed-off-by: Sasha Neftin Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igc: Remove Sequence Error Counter

2020-05-29T03:32:04Z

Accordance to the i225 datasheet sequence error counter does not applicable to the i225 device. This patch comes to clean up this counter. Signed-off-by: Sasha Neftin Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igc: Add Receive Error Counter

2020-05-29T03:30:06Z

Receive error counter reflect total number of non-filtered packets received with errors. This includes: CRC error, symbol error, Rx data error and carrier extend error. Signed-off-by: Sasha Neftin Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igc: Remove symbol error counter

2020-05-29T03:26:57Z

Accordance to the i225 datasheet symbol error counter does not applicable to the i225 device. This patch comes to clean up this counter. Signed-off-by: Sasha Neftin Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igc: Fix IGC_MAX_RXNFC_RULES

2020-05-29T03:15:38Z

IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES accordingly. Signed-off-by: Andre Guedes Acked-by: Sasha Neftin Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igc: Reject NFC rules with multiple matches

2020-05-29T03:13:11Z

The way Rx queue assignment based on mac address, Ethertype and VLAN priority filtering operates in I225 doesn't allow us to properly support NFC rules with multiple matches. Consider the following example which assigns to queue 2 frames matching the address MACADDR *and* Ethertype ETYPE. $ ethtool -N eth0 flow-type ether dst proto queue 2 When such rule is applied, we have 2 unwanted behaviors: 1) Any frame matching MACADDR will be assigned to queue 2. It doesn't matter the ETYPE value. 2) Any accepted frame that has Ethertype equals to ETYPE, no matter the mac address, will be assigned to queue 2 as well. In current code, multiple-match filters are accepted by the driver, even though it doesn't support them properly. This patch adds a check for multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are rejected. Signed-off-by: Andre Guedes Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher