kernel.git/drivers/net/ethernet/freescale, branch master

net: enetc: do not skip setting LaBCR[MDIO_PHYAD_PRTAD] for addr 0

2026-03-10T09:36:46Z

Given that some platforms may use PHY address 0 (I suppose the PHY may not treat address 0 as a broadcast address or default response address). It is possible for some boards to connect multiple PHYs to the same ENETC MAC, for example: - a PHY with a non-zero address connects to ENETC MAC through SGMII interface (selected via DTS_A) - a PHY with address 0 connects to ENETC MAC through RGMII interface (selected via DTS_B) For the case where the ENETC port MDIO is used to manage the PHY, when switching from DTS_A to DTS_B via soft reboot, LaBCR[MDIO_PHYAD_PRTAD] must be updated to 0 because the NETCMIX block is not reset during soft reboot. However, the current driver explicitly skips configuring address 0, causing LaBCR[MDIO_PHYAD_PRTAD] to retain its old value. Therefore, remove the special-case skip of PHY address 0 so that valid configurations using address 0 are properly supported. Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage") Fixes: 50bfd9c06f0f ("net: enetc: set external PHY address in IERB for i.MX94 ENETC") Reviewed-by: Clark Wang Signed-off-by: Wei Fang Link: https://patch.msgid.link/20260305031211.904812-3-wei.fang@nxp.com Signed-off-by: Paolo Abeni

net: enetc: fix incorrect fallback PHY address handling

2026-03-10T09:36:46Z

The current netc_get_phy_addr() implementation falls back to PHY address 0 when the "mdio" node or the PHY child node is missing. On i.MX95, this causes failures when a real PHY is actually assigned address 0 and is managed through the EMDIO interface. Because the bit 0 of phy_mask will be set, leading imx95_enetc_mdio_phyaddr_config() to return an error, and the netc_blk_ctrl driver probe subsequently fails. Fix this by returning -ENODEV when neither an "mdio" node nor any PHY node is present, it means that ENETC port MDIO is not used to manage the PHY, so there is no need to configure LaBCR[MDIO_PHYAD_PRTAD]. Reported-by: Alexander Stein Closes: https://lore.kernel.org/all/7825188.GXAFRqVoOG@steina-w Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage") Reviewed-by: Clark Wang Tested-by: Alexander Stein Signed-off-by: Wei Fang Link: https://patch.msgid.link/20260305031211.904812-2-wei.fang@nxp.com Signed-off-by: Paolo Abeni

net: enetc: use truesize as XDP RxQ info frag_size

2026-03-05T16:02:05Z

The only user of frag_size field in XDP RxQ info is bpf_xdp_frags_increase_tail(). It clearly expects truesize instead of DMA write size. Different assumptions in enetc driver configuration lead to negative tailroom. Set frag_size to the same value as frame_sz. Fixes: 2768b2e2f7d2 ("net: enetc: register XDP RX queues with frag_size") Reviewed-by: Aleksandr Loktionov Reviewed-by: Vladimir Oltean Signed-off-by: Larysa Zaremba Link: https://patch.msgid.link/20260305111253.2317394-9-larysa.zaremba@intel.com Signed-off-by: Jakub Kicinski

dpaa2-switch: Fix interrupt storm after receiving bad if_id in IRQ handler

2026-02-28T17:01:41Z

Commit 31a7a0bbeb00 ("dpaa2-switch: add bounds check for if_id in IRQ handler") introduces a range check for if_id to avoid an out-of-bounds access. If an out-of-bounds if_id is detected, the interrupt status is not cleared. This may result in an interrupt storm. Clear the interrupt status after detecting an out-of-bounds if_id to avoid the problem. Found by an experimental AI code review agent at Google. Fixes: 31a7a0bbeb00 ("dpaa2-switch: add bounds check for if_id in IRQ handler") Cc: Junrui Luo Signed-off-by: Guenter Roeck Reviewed-by: Ioana Ciornei Link: https://patch.msgid.link/20260227055812.1777915-1-linux@roeck-us.net Signed-off-by: Jakub Kicinski

Merge tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2026-02-26T16:00:13Z

Pull networking fixes from Paolo Abeni: "Including fixes from IPsec, Bluetooth and netfilter Current release - regressions: - wifi: fix dev_alloc_name() return value check - rds: fix recursive lock in rds_tcp_conn_slots_available Current release - new code bugs: - vsock: lock down child_ns_mode as write-once Previous releases - regressions: - core: - do not pass flow_id to set_rps_cpu() - consume xmit errors of GSO frames - netconsole: avoid OOB reads, msg is not nul-terminated - netfilter: h323: fix OOB read in decode_choice() - tcp: re-enable acceptance of FIN packets when RWIN is 0 - udplite: fix null-ptr-deref in __udp_enqueue_schedule_skb(). - wifi: brcmfmac: fix potential kernel oops when probe fails - phy: register phy led_triggers during probe to avoid AB-BA deadlock - eth: - bnxt_en: fix deleting of Ntuple filters - wan: farsync: fix use-after-free bugs caused by unfinished tasklets - xscale: check for PTP support properly Previous releases - always broken: - tcp: fix potential race in tcp_v6_syn_recv_sock() - kcm: fix zero-frag skb in frag_list on partial sendmsg error - xfrm: - fix race condition in espintcp_close() - always flush state and policy upon NETDEV_UNREGISTER event - bluetooth: - purge error queues in socket destructors - fix response to L2CAP_ECRED_CONN_REQ - eth: - mlx5: - fix circular locking dependency in dump - fix "scheduling while atomic" in IPsec MAC address query - gve: fix incorrect buffer cleanup for QPL - team: avoid NETDEV_CHANGEMTU event when unregistering slave - usb: validate USB endpoints" * tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits) netfilter: nf_conntrack_h323: fix OOB read in decode_choice() dpaa2-switch: validate num_ifs to prevent out-of-bounds write net: consume xmit errors of GSO frames vsock: document write-once behavior of the child_ns_mode sysctl vsock: lock down child_ns_mode as write-once selftests/vsock: change tests to respect write-once child ns mode net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query net/mlx5: Fix missing devlink lock in SRIOV enable error path net/mlx5: E-switch, Clear legacy flag when moving to switchdev net/mlx5: LAG, disable MPESW in lag_disable_change() net/mlx5: DR, Fix circular locking dependency in dump selftests: team: Add a reference count leak test team: avoid NETDEV_CHANGEMTU event when unregistering slave net: mana: Fix double destroy_workqueue on service rescan PCI path MAINTAINERS: Update maintainer entry for QUALCOMM ETHQOS ETHERNET DRIVER dpll: zl3073x: Remove redundant cleanup in devm_dpll_init() selftests/net: packetdrill: Verify acceptance of FIN packets when RWIN is 0 tcp: re-enable acceptance of FIN packets when RWIN is 0 vsock: Use container_of() to get net namespace in sysctl handlers net: usb: kaweth: validate USB endpoints ...

dpaa2-switch: validate num_ifs to prevent out-of-bounds write

2026-02-26T11:37:21Z

The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes() but never validates it against DPSW_MAX_IF (64). This value controls iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports num_ifs >= 64, the loop can write past the array bounds. Add a bound check for num_ifs in dpaa2_switch_init(). dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all ports match the flood filter, the loop fills all 64 slots and the control interface write overflows by one entry. The check uses >= because num_ifs == DPSW_MAX_IF is also functionally broken. build_if_id_bitmap() silently drops any ID >= 64: if (id[i] < DPSW_MAX_IF) bmap[id[i] / 64] |= ... Fixes: 539dda3c5d19 ("staging: dpaa2-switch: properly setup switching domains") Signed-off-by: Junrui Luo Reviewed-by: Ioana Ciornei Link: https://patch.msgid.link/SYBPR01MB78812B47B7F0470B617C408AAF74A@SYBPR01MB7881.ausprd01.prod.outlook.com Signed-off-by: Paolo Abeni

Convert remaining multi-line kmalloc_obj/flex GFP_KERNEL uses

2026-02-22T16:26:33Z

Conversion performed via this Coccinelle script: // SPDX-License-Identifier: GPL-2.0-only // Options: --include-headers-for-types --all-includes --include-headers --keep-comments virtual patch @gfp depends on patch && !(file in "tools") && !(file in "samples")@ identifier ALLOC = {kmalloc_obj,kmalloc_objs,kmalloc_flex, kzalloc_obj,kzalloc_objs,kzalloc_flex, kvmalloc_obj,kvmalloc_objs,kvmalloc_flex, kvzalloc_obj,kvzalloc_objs,kvzalloc_flex}; @@ ALLOC(... - , GFP_KERNEL ) $ make coccicheck MODE=patch COCCI=gfp.cocci Build and boot tested x86_64 with Fedora 42's GCC and Clang: Linux version 6.19.0+ (user@host) (gcc (GCC) 15.2.1 20260123 (Red Hat 15.2.1-7), GNU ld version 2.44-12.fc42) #1 SMP PREEMPT_DYNAMIC 1970-01-01 Linux version 6.19.0+ (user@host) (clang version 20.1.8 (Fedora 20.1.8-4.fc42), LLD 20.1.8) #1 SMP PREEMPT_DYNAMIC 1970-01-01 Signed-off-by: Kees Cook Signed-off-by: Linus Torvalds

Convert more 'alloc_obj' cases to default GFP_KERNEL arguments

2026-02-22T04:03:00Z

This converts some of the visually simpler cases that have been split over multiple lines. I only did the ones that are easy to verify the resulting diff by having just that final GFP_KERNEL argument on the next line. Somebody should probably do a proper coccinelle script for this, but for me the trivial script actually resulted in an assertion failure in the middle of the script. I probably had made it a bit _too_ trivial. So after fighting that far a while I decided to just do some of the syntactically simpler cases with variations of the previous 'sed' scripts. The more syntactically complex multi-line cases would mostly really want whitespace cleanup anyway. Signed-off-by: Linus Torvalds

Convert 'alloc_flex' family to use the new default GFP_KERNEL argument

2026-02-22T01:09:51Z

This is the exact same thing as the 'alloc_obj()' version, only much smaller because there are a lot fewer users of the *alloc_flex() interface. As with alloc_obj() version, this was done entirely with mindless brute force, using the same script, except using 'flex' in the pattern rather than 'objs*'. Signed-off-by: Linus Torvalds

Convert 'alloc_obj' family to use the new default GFP_KERNEL argument

2026-02-22T01:09:51Z

This was done entirely with mindless brute force, using git grep -l '\