kernel.git/drivers/net/ethernet/broadcom, branch linux-4.19.y

tg3: Set coherent DMA mask bits to 31 for BCM57766 chipsets

2024-12-05T09:59:37Z

[ Upstream commit 614f4d166eeeb9bd709b0ad29552f691c0f45776 ] The hardware on Broadcom 1G chipsets have a known limitation where they cannot handle DMA addresses that cross over 4GB. When such an address is encountered, the hardware sets the address overflow error bit in the DMA status register and triggers a reset. However, BCM57766 hardware is setting the overflow bit and triggering a reset in some cases when there is no actual underlying address overflow. The hardware team analyzed the issue and concluded that it is happening when the status block update has an address with higher (b16 to b31) bits as 0xffff following a previous update that had lowest bits as 0xffff. To work around this bug in the BCM57766 hardware, set the coherent dma mask from the current 64b to 31b. This will ensure that upper bits of the status block DMA address are always at most 0x7fff, thus avoiding the improper overflow check described above. This work around is intended for only status block and ring memories and has no effect on TX and RX buffers as they do not require coherent memory. Fixes: 72f2afb8a685 ("[TG3]: Add DMA address workaround") Reported-by: Salam Noureddine Reviewed-by: Kalesh AP Reviewed-by: Somnath Kotur Signed-off-by: Pavan Chebbi Reviewed-by: Michal Kubiak Link: https://patch.msgid.link/20241119055741.147144-1-pavan.chebbi@broadcom.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: systemport: fix potential memory leak in bcm_sysport_xmit()

2024-11-08T15:19:20Z

[ Upstream commit c401ed1c709948e57945485088413e1bb5e94bd1 ] The bcm_sysport_xmit() returns NETDEV_TX_OK without freeing skb in case of dma_map_single() fails, add dev_kfree_skb() to fix it. Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Wang Hai Link: https://patch.msgid.link/20241014145115.44977-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

bnx2x: Fix multiple UBSAN array-index-out-of-bounds

2024-07-18T09:39:36Z

commit 134061163ee5ca4759de5c24ca3bd71608891ba7 upstream. Fix UBSAN warnings that occur when using a system with 32 physical cpu cores or more, or when the user defines a number of Ethernet queues greater than or equal to FP_SB_MAX_E1x using the num_queues module parameter. Currently there is a read/write out of bounds that occurs on the array "struct stats_query_entry query" present inside the "bnx2x_fw_stats_req" struct in "drivers/net/ethernet/broadcom/bnx2x/bnx2x.h". Looking at the definition of the "struct stats_query_entry query" array: struct stats_query_entry query[FP_SB_MAX_E1x+ BNX2X_FIRST_QUEUE_QUERY_IDX]; FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3 meaning the array has a total size of 19. Since accesses to "struct stats_query_entry query" are offset-ted by BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet queues should not exceed FP_SB_MAX_E1x (16). However one of these queues is reserved for FCOE and thus the number of Ethernet queues should be set to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if it is not. This is also described in a comment in the source code in drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition of FP_SB_MAX_E1x. Below is the part of this explanation that it important for this patch /* * The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is * control by the number of fast-path status blocks supported by the * device (HW/FW). Each fast-path status block (FP-SB) aka non-default * status block represents an independent interrupts context that can * serve a regular L2 networking queue. However special L2 queues such * as the FCoE queue do not require a FP-SB and other components like * the CNIC may consume FP-SB reducing the number of possible L2 queues * * If the maximum number of FP-SB available is X then: * a. If CNIC is supported it consumes 1 FP-SB thus the max number of * regular L2 queues is Y=X-1 * b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor) * c. If the FCoE L2 queue is supported the actual number of L2 queues * is Y+1 * d. The number of irqs (MSIX vectors) is either Y+1 (one extra for * slow-path interrupts) or Y+2 if CNIC is supported (one additional * FP interrupt context for the CNIC). * e. The number of HW context (CID count) is always X or X+1 if FCoE * L2 queue is supported. The cid for the FCoE L2 queue is always X. */ However this driver also supports NICs that use the E2 controller which can handle more queues due to having more FP-SB represented by FP_SB_MAX_E2. Looking at the commits when the E2 support was added, it was originally using the E1x parameters: commit f2e0899f0f27 ("bnx2x: Add 57712 support"). Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver was later updated to take full advantage of the E2 instead of having it be limited to the capabilities of the E1x. But as far as we can tell, the array "stats_query_entry query" was still limited to using the FP-SB available to the E1x cards as part of an oversignt when the driver was updated to take full advantage of the E2, and now with the driver being aware of the greater queue size supported by E2 NICs, it causes the UBSAN warnings seen in the stack traces below. This patch increases the size of the "stats_query_entry query" array by replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle both types of NICs. Stack traces: UBSAN: array-index-out-of-bounds in drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11 index 20 is out of range for type 'stats_query_entry [19]' CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic #202405052133 Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9, BIOS P89 10/21/2019 Call Trace: dump_stack_lvl+0x76/0xa0 dump_stack+0x10/0x20 __ubsan_handle_out_of_bounds+0xcb/0x110 bnx2x_prep_fw_stats_req+0x2e1/0x310 [bnx2x] bnx2x_stats_init+0x156/0x320 [bnx2x] bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x] bnx2x_nic_load+0x8e8/0x19e0 [bnx2x] bnx2x_open+0x16b/0x290 [bnx2x] __dev_open+0x10e/0x1d0 RIP: 0033:0x736223927a0a Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89 RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003 RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080 R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0 R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00 ---[ end trace ]--- ------------[ cut here ]------------ UBSAN: array-index-out-of-bounds in drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1546:11 index 28 is out of range for type 'stats_query_entry [19]' CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic #202405052133 Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9, BIOS P89 10/21/2019 Call Trace: dump_stack_lvl+0x76/0xa0 dump_stack+0x10/0x20 __ubsan_handle_out_of_bounds+0xcb/0x110 bnx2x_prep_fw_stats_req+0x2fd/0x310 [bnx2x] bnx2x_stats_init+0x156/0x320 [bnx2x] bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x] bnx2x_nic_load+0x8e8/0x19e0 [bnx2x] bnx2x_open+0x16b/0x290 [bnx2x] __dev_open+0x10e/0x1d0 RIP: 0033:0x736223927a0a Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89 RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003 RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080 R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0 R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00 ---[ end trace ]--- ------------[ cut here ]------------ UBSAN: array-index-out-of-bounds in drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1895:8 index 29 is out of range for type 'stats_query_entry [19]' CPU: 13 PID: 163 Comm: kworker/u96:1 Not tainted 6.9.0-060900rc7-generic #202405052133 Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9, BIOS P89 10/21/2019 Workqueue: bnx2x bnx2x_sp_task [bnx2x] Call Trace: dump_stack_lvl+0x76/0xa0 dump_stack+0x10/0x20 __ubsan_handle_out_of_bounds+0xcb/0x110 bnx2x_iov_adjust_stats_req+0x3c4/0x3d0 [bnx2x] bnx2x_storm_stats_post.part.0+0x4a/0x330 [bnx2x] ? bnx2x_hw_stats_post+0x231/0x250 [bnx2x] bnx2x_stats_start+0x44/0x70 [bnx2x] bnx2x_stats_handle+0x149/0x350 [bnx2x] bnx2x_attn_int_asserted+0x998/0x9b0 [bnx2x] bnx2x_sp_task+0x491/0x5c0 [bnx2x] process_one_work+0x18d/0x3f0 ---[ end trace ]--- Fixes: 50f0a562f8cc ("bnx2x: add fcoe statistics") Signed-off-by: Ghadi Elie Rahme Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20240627111405.1037812-1-ghadi.rahme@canonical.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: bcmgenet: Reset RBUF on first open

2024-05-17T09:42:39Z

[ Upstream commit 0a6380cb4c6b5c1d6dad226ba3130f9090f0ccea ] If the RBUF logic is not reset when the kernel starts then there may be some data left over from any network boot loader. If the 64-byte packet headers are enabled then this can be fatal. Extend bcmgenet_dma_disable to do perform the reset, but not when called from bcmgenet_resume in order to preserve a wake packet. N.B. This different handling of resume is just based on a hunch - why else wouldn't one reset the RBUF as well as the TBUF? If this isn't the case then it's easy to change the patch to make the RBUF reset unconditional. See: https://github.com/raspberrypi/linux/issues/3850 See: https://github.com/raspberrypi/firmware/issues/1882 Signed-off-by: Phil Elwell Signed-off-by: Maarten Vanraes Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: b44: set pause params only when interface is up

2024-05-02T14:17:13Z

commit e3eb7dd47bd4806f00e104eb6da092c435f9fb21 upstream. b44_free_rings() accesses b44::rx_buffers (and ::tx_buffers) unconditionally, but b44::rx_buffers is only valid when the device is up (they get allocated in b44_open(), and deallocated again in b44_close()), any other time these are just a NULL pointers. So if you try to change the pause params while the network interface is disabled/administratively down, everything explodes (which likely netifd tries to do). Link: https://github.com/openwrt/openwrt/issues/13789 Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2) Cc: stable@vger.kernel.org Reported-by: Peter Münster Suggested-by: Jonas Gorski Signed-off-by: Vaclav Svoboda Tested-by: Peter Münster Reviewed-by: Andrew Lunn Signed-off-by: Peter Münster Reviewed-by: Michael Chan Link: https://lore.kernel.org/r/87y192oolj.fsf@a16n.net Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net/bnx2x: Prevent access to a freed page in page_pool

2024-03-26T22:22:43Z

[ Upstream commit d27e2da94a42655861ca4baea30c8cd65546f25d ] Fix race condition leading to system crash during EEH error handling During EEH error recovery, the bnx2x driver's transmit timeout logic could cause a race condition when handling reset tasks. The bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(), which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload() SGEs are freed using bnx2x_free_rx_sge_range(). However, this could overlap with the EEH driver's attempt to reset the device using bnx2x_io_slot_reset(), which also tries to free SGEs. This race condition can result in system crashes due to accessing freed memory locations in bnx2x_free_rx_sge() 799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp, 800 struct bnx2x_fastpath *fp, u16 index) 801 { 802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index]; 803 struct page *page = sw_buf->page; .... where sw_buf was set to NULL after the call to dma_unmap_page() by the preceding thread. EEH: Beginning: 'slot_reset' PCI 0011:01:00.0#10000: EEH: Invoking bnx2x->slot_reset() bnx2x: [bnx2x_io_slot_reset:14228(eth1)]IO slot reset initializing... bnx2x 0011:01:00.0: enabling device (0140 -> 0142) bnx2x: [bnx2x_io_slot_reset:14244(eth1)]IO slot reset --> driver unload Kernel attempted to read user page (0) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x00000000 Faulting instruction address: 0xc0080000025065fc Oops: Kernel access of bad area, sig: 11 [#1] ..... Call Trace: [c000000003c67a20] [c00800000250658c] bnx2x_io_slot_reset+0x204/0x610 [bnx2x] (unreliable) [c000000003c67af0] [c0000000000518a8] eeh_report_reset+0xb8/0xf0 [c000000003c67b60] [c000000000052130] eeh_pe_report+0x180/0x550 [c000000003c67c70] [c00000000005318c] eeh_handle_normal_event+0x84c/0xa60 [c000000003c67d50] [c000000000053a84] eeh_event_handler+0xf4/0x170 [c000000003c67da0] [c000000000194c58] kthread+0x1c8/0x1d0 [c000000003c67e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64 To solve this issue, we need to verify page pool allocations before freeing. Fixes: 4cace675d687 ("bnx2x: Alloc 4k fragment for each rx ring buffer element") Signed-off-by: Thinh Tran Reviewed-by: Jiri Pirko Link: https://lore.kernel.org/r/20240315205535.1321-1-thinhtr@linux.ibm.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net/tg3: fix race condition in tg3_reset_task()

2024-01-25T22:33:29Z

[ Upstream commit 16b55b1f2269962fb6b5154b8bf43f37c9a96637 ] When an EEH error is encountered by a PCI adapter, the EEH driver modifies the PCI channel's state as shown below: enum { /* I/O channel is in normal state */ pci_channel_io_normal = (__force pci_channel_state_t) 1, /* I/O to channel is blocked */ pci_channel_io_frozen = (__force pci_channel_state_t) 2, /* PCI card is dead */ pci_channel_io_perm_failure = (__force pci_channel_state_t) 3, }; If the same EEH error then causes the tg3 driver's transmit timeout logic to execute, the tg3_tx_timeout() function schedules a reset task via tg3_reset_task_schedule(), which may cause a race condition between the tg3 and EEH driver as both attempt to recover the HW via a reset action. EEH driver gets error event --> eeh_set_channel_state() and set device to one of error state above scheduler: tg3_reset_task() get returned error from tg3_init_hw() --> dev_close() shuts down the interface tg3_io_slot_reset() and tg3_io_resume() fail to reset/resume the device To resolve this issue, we avoid the race condition by checking the PCI channel state in the tg3_reset_task() function and skip the tg3 driver initiated reset when the PCI channel is not in the normal state. (The driver has no access to tg3 device registers at this point and cannot even complete the reset task successfully without external assistance.) We'll leave the reset procedure to be managed by the EEH driver which calls the tg3_io_error_detected(), tg3_io_slot_reset() and tg3_io_resume() functions as appropriate. Adding the same checking in tg3_dump_state() to avoid dumping all device registers when the PCI channel is not in the normal state. Signed-off-by: Thinh Tran Tested-by: Venkata Sai Duggi Reviewed-by: David Christensen Reviewed-by: Michael Chan Link: https://lore.kernel.org/r/20231201001911.656-1-thinhtr@linux.vnet.ibm.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()

2024-01-15T17:23:42Z

[ Upstream commit e009b2efb7a8850498796b360043ac25c8d3d28f ] The 2 lines to check for the BNXT_HWRM_PF_UNLOAD_SP_EVENT bit was mis-applied to bnxt_cfg_ntp_filters() and should have been applied to bnxt_sp_task(). Fixes: 19241368443f ("bnxt_en: Send PF driver unload notification to all VFs.") Reviewed-by: Andy Gospodarek Signed-off-by: Michael Chan Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: bcmgenet: Fix FCS generation for fragmented skbuffs

2024-01-15T17:23:41Z

[ Upstream commit e584f2ff1e6cc9b1d99e8a6b0f3415940d1b3eb3 ] The flag DMA_TX_APPEND_CRC was only written to the first DMA descriptor in the TX path, where each descriptor corresponds to a single skbuff fragment (or the skbuff head). This led to packets with no FCS appearing on the wire if the kernel allocated the packet in fragments, which would always happen when using PACKET_MMAP/TPACKET (cf. tpacket_fill_skb() in net/af_packet.c). Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Adrian Cinal Acked-by: Doug Berger Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/20231228135638.1339245-1-adriancinal1@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

tg3: Increment tx_dropped in tg3_tso_bug()

2023-12-13T16:42:15Z

[ Upstream commit 17dd5efe5f36a96bd78012594fabe21efb01186b ] tg3_tso_bug() drops a packet if it cannot be segmented for any reason. The number of discarded frames should be incremented accordingly. Signed-off-by: Alex Pakhunov Signed-off-by: Vincent Wong Reviewed-by: Pavan Chebbi Link: https://lore.kernel.org/r/20231113182350.37472-2-alexey.pakhunov@spacex.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin