kernel.git/drivers/net/ethernet/amd, branch linux-4.19.y

net: amd: mvme147: Fix probe banner message

2024-11-08T15:19:23Z

[ Upstream commit 82c5b53140faf89c31ea2b3a0985a2f291694169 ] Currently this driver prints this line with what looks like a rogue format specifier when the device is probed: [ 2.840000] eth%d: MVME147 at 0xfffe1800, irq 12, Hardware Address xx:xx:xx:xx:xx:xx Change the printk() for netdev_info() and move it after the registration has completed so it prints out the name of the interface properly. Signed-off-by: Daniel Palmer Reviewed-by: Simon Horman Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

amd-xgbe: propagate the correct speed and duplex status

2023-12-08T07:43:23Z

[ Upstream commit 7a2323ac24a50311f64a3a9b54ed5bef5821ecae ] xgbe_get_link_ksettings() does not propagate correct speed and duplex information to ethtool during cable unplug. Due to which ethtool reports incorrect values for speed and duplex. Address this by propagating correct information. Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe") Acked-by: Shyam Sundar S K Signed-off-by: Raju Rangoju Reviewed-by: Wojciech Drewek Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

amd-xgbe: handle the corner-case during tx completion

2023-12-08T07:43:23Z

[ Upstream commit 7121205d5330c6a3cb3379348886d47c77b78d06 ] The existing implementation uses software logic to accumulate tx completions until the specified time (1ms) is met and then poll them. However, there exists a tiny gap which leads to a race between resetting and checking the tx_activate flag. Due to this the tx completions are not reported to upper layer and tx queue timeout kicks-in restarting the device. To address this, introduce a tx cleanup mechanism as part of the periodic maintenance process. Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver") Acked-by: Shyam Sundar S K Signed-off-by: Raju Rangoju Reviewed-by: Wojciech Drewek Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

amd-xgbe: handle corner-case during sfp hotplug

2023-12-08T07:43:23Z

[ Upstream commit 676ec53844cbdf2f47e68a076cdff7f0ec6cbe3f ] Force the mode change for SFI in Fixed PHY configurations. Fixed PHY configurations needs PLL to be enabled while doing mode set. When the SFP module isn't connected during boot, driver assumes AN is ON and attempts auto-negotiation. However, if the connected SFP comes up in Fixed PHY configuration the link will not come up as PLL isn't enabled while the initial mode set command is issued. So, force the mode change for SFI in Fixed PHY configuration to fix link issues. Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy") Acked-by: Shyam Sundar S K Signed-off-by: Raju Rangoju Reviewed-by: Wojciech Drewek Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

amd-xgbe: fix the false linkup in xgbe_phy_status

2023-06-09T08:23:55Z

[ Upstream commit dc362e20cd6ab7a93d1b09669730c406f0910c35 ] In the event of a change in XGBE mode, the current auto-negotiation needs to be reset and the AN cycle needs to be re-triggerred. However, the current code ignores the return value of xgbe_set_mode(), leading to false information as the link is declared without checking the status register. Fix this by propagating the mode switch status information to xgbe_phy_status(). Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy") Co-developed-by: Sudheesh Mavila Signed-off-by: Sudheesh Mavila Reviewed-by: Simon Horman Acked-by: Shyam Sundar S K Signed-off-by: Raju Rangoju Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: amd: Fix link leak when verifying config failed

2023-05-17T09:13:15Z

[ Upstream commit d325c34d9e7e38d371c0a299d415e9b07f66a1fb ] After failing to verify configuration, it returns directly without releasing link, which may cause memory leak. Paolo Abeni thinks that the whole code of this driver is quite "suboptimal" and looks unmainatained since at least ~15y, so he suggests that we could simply remove the whole driver, please take it into consideration. Simon Horman suggests that the fix label should be set to "Linux-2.6.12-rc2" considering that the problem has existed since the driver was introduced and the commit above doesn't seem to exist in net/net-next. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gan Gecen Reviewed-by: Dongliang Mu Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

amd-xgbe: Delay AN timeout during KR training

2023-02-06T06:49:38Z

[ Upstream commit 926446ae24c03311a480fb96eb78f0ce7ea6d091 ] AN restart triggered during KR training not only aborts the KR training process but also move the HW to unstable state. Driver has to wait upto 500ms or until the KR training is completed before restarting AN cycle. Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe") Co-developed-by: Sudheesh Mavila Signed-off-by: Sudheesh Mavila Signed-off-by: Raju Rangoju Acked-by: Shyam Sundar S K Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

amd-xgbe: TX Flow Ctrl Registers are h/w ver dependent

2023-02-06T06:49:38Z

[ Upstream commit 579923d84b04abb6cd4cd1fd9974096a2dd1832b ] There is difference in the TX Flow Control registers (TFCR) between the revisions of the hardware. The older revisions of hardware used to have single register per queue. Whereas, the newer revision of hardware (from ver 30H onwards) have one register per priority. Update the driver to use the TFCR based on the reported version of the hardware. Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver") Co-developed-by: Ajith Nayak Signed-off-by: Ajith Nayak Signed-off-by: Raju Rangoju Acked-by: Shyam Sundar S K Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: amd-xgbe: add missed tasklet_kill

2023-01-18T10:30:49Z

[ Upstream commit d530ece70f16f912e1d1bfeea694246ab78b0a4b ] The driver does not call tasklet_kill in several places. Add the calls to fix it. Fixes: 85b85c853401 ("amd-xgbe: Re-issue interrupt if interrupt status not cleared") Signed-off-by: Jiguang Xiao Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: amd-xgbe: Check only the minimum speed for active/passive cables

2023-01-18T10:30:19Z

[ Upstream commit f8ab263d4d48e6dab752029bf562f20a2ee630ed ] There are cables that exist that can support speeds in excess of 10GbE. The driver, however, restricts the EEPROM advertised nominal bitrate to a specific range, which can prevent usage of cables that can support, for example, up to 25GbE. Rather than checking that an active or passive cable supports a specific range, only check for a minimum supported speed. Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller Signed-off-by: Sasha Levin