kernel.git/drivers/net/ethernet/Makefile, branch linux-3.5.y

Ethernet driver for the WIZnet W5300 chip

2012-04-05T05:43:02Z

Based on original driver from chip manufacturer, but nearly full rewite. Tested and used in production with Blackfin BF531 embedded processor. Signed-off-by: Mike Sinkovsky Signed-off-by: David S. Miller

lpc32xx: Added ethernet driver

2012-03-13T00:08:34Z

This patch adds an ethernet driver for the LPC32xx ARM SoC. Signed-off-by: Roland Stigge Signed-off-by: David S. Miller

Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2012-01-09T22:39:22Z

Driver specific changes Again, a lot of platforms have changes in here: pxa, samsung, omap, at91, imx, ... * tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits) ARM: sa1100: clean up of the clock support ARM: pxa: add dummy clock for sa1100-rtc RTC: sa1100: support sa1100, pxa and mmp soc families RTC: sa1100: remove redundant code of setting alarm RTC: sa1100: Clean out ost register Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq() pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq() ARM: EXYNOS: Modified files for SPI consolidation work ARM: S5P64X0: Enable SDHCI support ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names ARM: S5P64X0: Add HSMMC setup for host Controller ARM: EXYNOS: Add USB OHCI support to ORIGEN board USB: Add Samsung Exynos OHCI diver ARM: EXYNOS: Add USB OHCI support to SMDKV310 board ARM: EXYNOS: Add USB OHCI device net: macb: fix build break with !CONFIG_OF i2c: tegra: Support DVC controller in device tree i2c: tegra: Add __devinit/exit to probe/remove net/at91_ether: use gpio_is_valid for phy IRQ line ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT ...

net: add calxeda xgmac ethernet driver

2011-11-29T06:15:24Z

Add support for the XGMAC 10Gb ethernet device in the Calxeda Highbank SOC. Signed-off-by: Rob Herring Signed-off-by: David S. Miller

macb: initial support for Cadence GEM

2011-11-22T15:21:17Z

The Cadence GEM is based on the MACB Ethernet controller but has a few small changes with regards to register and bitfield placement. This patch detects the presence of a GEM by reading the module ID register and setting a flag appropriately. This handles the new HW address, USRIO and hash register base register locations in GEM. v3: - convert to macb_is_gem() inline rather than storing a boolean flag - handle rx_overrun stats for gem Acked-by: David S. Miller Acked-by: Nicolas Ferre Cc: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Jamie Iles Tested-by: Jean-Christophe PLAGNIOL-VILLARD

net/ethernet: sc92031 is not Realtek

2011-11-01T23:30:38Z

While the SC92031 could be found on fake "Realtek" NICs, it has no relationship to Realtek, and is actually from Silan. Create a new subdirectory for silan and move sc92031 there. Signed-off-by: Cesar Eduardo Barros Signed-off-by: David S. Miller

acenic: Move the Alteon driver

2011-08-13T07:37:14Z

Based on feedback from Alan Cox, the acenic driver moved to drivers/net/ethernet/alteon/ and made the necessary Kconfig and Makefile changes. CC: Jes Sorensen CC: Alan Cox Signed-off-by: Jeff Kirsher

tile: Move the Tilera driver

2011-08-13T06:47:53Z

Move the Tilera driver into drivers/net/ethernet/tile and make the necessary Kconfig and Makefile changes. Updated the Kconfig so that the options defualt to y if TILE kernel. CC: Chris Metcalf Signed-off-by: Jeff Kirsher

xircom: Move the Xircom driver

2011-08-13T06:47:43Z

Move the Xircom driver into drivers/net/ethernet/xircom/ and make the necessary Kconfig and Makefile changes. CC: CC: Dominik Brodowski Signed-off-by: Jeff Kirsher

sh_eth: Move the Renesas SuperH driver

2011-08-13T06:47:36Z

Move the Renesas driver into drivers/net/ethernet/renesas/ and make the necessary Kconfig and Makefile changes. CC: Yoshihiro Shimoda Signed-off-by: Jeff Kirsher