kernel.git/drivers/net/can/flexcan.c, branch linux-4.9.y

can: flexcan: flexcan_chip_freeze(): fix chip freeze for missing bitrate

2021-04-10T11:04:45Z

commit 47c5e474bc1e1061fb037d13b5000b38967eb070 upstream. For cases when flexcan is built-in, bitrate is still not set at registering. So flexcan_chip_freeze() generates: [ 1.860000] *** ZERO DIVIDE *** FORMAT=4 [ 1.860000] Current process id is 1 [ 1.860000] BAD KERNEL TRAP: 00000000 [ 1.860000] PC: [<402e70c8>] flexcan_chip_freeze+0x1a/0xa8 To allow chip freeze, using an hardcoded timeout when bitrate is still not set. Fixes: ec15e27cc890 ("can: flexcan: enable RX FIFO after FRZ/HALT valid") Link: https://lore.kernel.org/r/20210315231510.650593-1-angelo@kernel-space.org Signed-off-by: Angelo Dureghello [mkl: use if instead of ? operator] Signed-off-by: Marc Kleine-Budde Cc: Koen Vandeputte Signed-off-by: Greg Kroah-Hartman

can: flexcan: enable RX FIFO after FRZ/HALT valid

2021-03-17T15:10:13Z

commit ec15e27cc8904605846a354bb1f808ea1432f853 upstream. RX FIFO enable failed could happen when do system reboot stress test: [ 0.303958] flexcan 5a8d0000.can: 5a8d0000.can supply xceiver not found, using dummy regulator [ 0.304281] flexcan 5a8d0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core [ 0.314640] flexcan 5a8d0000.can: registering netdev failed [ 0.320728] flexcan 5a8e0000.can: 5a8e0000.can supply xceiver not found, using dummy regulator [ 0.320991] flexcan 5a8e0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core [ 0.331360] flexcan 5a8e0000.can: registering netdev failed [ 0.337444] flexcan 5a8f0000.can: 5a8f0000.can supply xceiver not found, using dummy regulator [ 0.337716] flexcan 5a8f0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core [ 0.348117] flexcan 5a8f0000.can: registering netdev failed RX FIFO should be enabled after the FRZ/HALT are valid. But the current code enable RX FIFO and FRZ/HALT at the same time. Fixes: e955cead03117 ("CAN: Add Flexcan CAN controller driver") Link: https://lore.kernel.org/r/20210218110037.16591-3-qiangqing.zhang@nxp.com Signed-off-by: Joakim Zhang Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: flexcan: assert FRZ bit in flexcan_chip_freeze()

2021-03-17T15:10:13Z

commit 449052cfebf624b670faa040245d3feed770d22f upstream. Assert HALT bit to enter freeze mode, there is a premise that FRZ bit is asserted. This patch asserts FRZ bit in flexcan_chip_freeze, although the reset value is 1b'1. This is a prepare patch, later patch will invoke flexcan_chip_freeze() to enter freeze mode, which polling freeze mode acknowledge. Fixes: b1aa1c7a2165b ("can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze") Link: https://lore.kernel.org/r/20210218110037.16591-2-qiangqing.zhang@nxp.com Signed-off-by: Joakim Zhang Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: flexcan: disable completely the ECC mechanism

2019-11-12T18:16:10Z

[ Upstream commit 5e269324db5adb2f5f6ec9a93a9c7b0672932b47 ] The ECC (memory error detection and correction) mechanism can be activated or not, controlled by the ECCDIS bit in CAN_MECR. When disabled, updates on indications and reporting registers are stopped. So if want to disable ECC completely, had better assert ECCDIS bit, not just mask the related interrupts. Fixes: cdce844865be ("can: flexcan: add vf610 support for FlexCAN") Signed-off-by: Joakim Zhang Cc: linux-stable Signed-off-by: Marc Kleine-Budde Signed-off-by: Sasha Levin

can: flexcan: fix timeout when set small bitrate

2019-07-10T07:55:33Z

commit 247e5356a709eb49a0d95ff2a7f07dac05c8252c upstream. Current we can meet timeout issue when setting a small bitrate like 10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock = 30MHZ): | root@imx6ul7d:~# ip link set can0 up type can bitrate 10000 A link change request failed with some changes committed already. Interface can0 may have been left with an inconsistent configuration, please check. | RTNETLINK answers: Connection timed out It is caused by calling of flexcan_chip_unfreeze() timeout. Originally the code is using usleep_range(10, 20) for unfreeze operation, but the patch (8badd65 can: flexcan: avoid calling usleep_range from interrupt context) changed it into udelay(10) which is only a half delay of before, there're also some other delay changes. After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue. Meanwhile, Rasmus Villemoes reported that even with a timeout of 100, flexcan_probe() fails on the MPC8309, which requires a value of at least 140 to work reliably. 250 works for everyone. Signed-off-by: Joakim Zhang Reviewed-by: Dong Aisheng Cc: linux-stable Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: flex_can: Correct the checking for frame length in flexcan_start_xmit()

2018-03-03T09:23:27Z

[ Upstream commit 13454c14550065fcc1705d6bd4ee6d40e057099f ] The flexcan_start_xmit() function compares the frame length with data register length to write frame content into data[0] and data[1] register. Data register length is 4 bytes and frame maximum length is 8 bytes. Fix the check that compares frame length with 3. Because the register length is 4. Signed-off-by: Luu An Phu Reviewed-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

can: flexcan: fix resume function

2016-09-19T14:09:05Z

On a imx6ul-pico board the following error is seen during system suspend: dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110 PM: Device 2090000.flexcan failed to resume: error -110 The reason for this suspend error is because when the CAN interface is not active the clocks are disabled and then flexcan_chip_enable() will always fail due to a timeout error. In order to fix this issue, only call flexcan_chip_enable/disable() when the CAN interface is active. Based on a patch from Dong Aisheng in the NXP kernel. Signed-off-by: Fabio Estevam Cc: linux-stable Signed-off-by: Marc Kleine-Budde

can: fix assignment of error location in CAN error messages

2015-11-23T08:37:34Z

As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187 the assignment of the error location in CAN error messages had some bit wise overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines a single value which points to a location inside the CAN frame on the wire. This patch fixes the assignments for the error locations in error messages. Reported-by: Dan Carpenter Signed-off-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde

can: flexcan: enable interrupts atomically at the end of flexcan_chip_start()

2015-09-21T06:38:23Z

This patch defers the writing of the interrupts bits of the CTRL register order to enables all interrupts atomically at the the of the flexcan_chip_start() function. Suggested-by: Torsten Lang Signed-off-by: Marc Kleine-Budde

can: flexcan: give member of flexcan_priv holding mailboxes a sensible name

2015-09-21T06:38:23Z

This patch gives the member of flexcan_priv holding mailboxes a sensible name, by renaming from "cantxfg" to "mb": struct flexcan_priv::cantxfg -> struct flexcan_priv::mb Signed-off-by: Marc Kleine-Budde