kernel.git/drivers/net/can/c_can, branch linux-5.8.y

treewide: replace '---help---' in Kconfig files with 'help'

2020-06-13T16:57:21Z

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada

can: c_can: c_can_plaform: fix checkpatch warnings

2019-11-11T20:58:08Z

This patch fixes several checkpatch warnings in the c_can_platform driver glue code. Signed-off-by: Marc Kleine-Budde

can: c_can: C_CAN: add bus recovery events

2019-11-04T20:47:21Z

While the state is updated when the error counters increase and decrease, there is no event when the bus recovers and the error counters decrease again. So add that event as well. Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING -> ERROR_ACTIVE instead of directly to ERROR_ACTIVE again. Signed-off-by: Jeroen Hofstee Acked-by: Kurt Van Dijck Tested-by: Kurt Van Dijck Signed-off-by: Marc Kleine-Budde

can: c_can: D_CAN: c_can_chip_config(): perform a sofware reset on open

2019-11-04T20:47:21Z

When the CAN interface is closed it the hardwre is put in power down mode, but does not reset the error counters / state. Reset the D_CAN on open, so the reported state and the actual state match. According to [1], the C_CAN module doesn't have the software reset. [1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf Signed-off-by: Jeroen Hofstee Signed-off-by: Marc Kleine-Budde

can: c_can: c_can_poll(): only read status register after status IRQ

2019-11-04T20:47:21Z

When the status register is read without the status IRQ pending, the chip may not raise the interrupt line for an upcoming status interrupt and the driver may miss a status interrupt. It is critical that the BUSOFF status interrupt is forwarded to the higher layers, since no more interrupts will follow without intervention. Thanks to Wolfgang and Joe for bringing up the first idea. Signed-off-by: Kurt Van Dijck Cc: Wolfgang Grandegger Cc: Joe Burmeister Fixes: fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts") Cc: linux-stable Signed-off-by: Marc Kleine-Budde

treewide: Add SPDX license identifier - Makefile/Kconfig

2019-05-21T08:50:46Z

Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

can: c_can_pci: make c_can_pci_data const

2017-12-01T08:14:22Z

Make c_can_pci_data structures const as they are only used during a copy operation. Signed-off-by: Bhumika Goyal Signed-off-by: Marc Kleine-Budde

can: c_can: don't indicate triple sampling support for D_CAN

2017-11-10T08:15:28Z

The D_CAN controller doesn't provide a triple sampling mode, so don't set the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling triple sampling is a no-op. Signed-off-by: Richard Schütz Cc: linux-stable # >= v3.6 Signed-off-by: Marc Kleine-Budde

can: constify platform_device_id

2017-08-14T03:12:23Z

platform_device_id are not supposed to change at runtime. All functions working with platform_device_id provided by work with const platform_device_id. So mark the non-const structs as const. Signed-off-by: Arvind Yadav Signed-off-by: David S. Miller

drivers: net: generalize napi_complete_done()

2017-01-30T20:10:42Z

napi_complete_done() allows to opt-in for gro_flush_timeout, added back in linux-3.19, commit 3b47d30396ba ("net: gro: add a per device gro flush timer") This allows for more efficient GRO aggregation without sacrifying latencies. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller