kernel.git/drivers/net/can/c_can, branch linux-4.4.y

can: c_can: move runtime PM enable/disable to c_can_platform

2021-03-30T12:45:00Z

[ Upstream commit 6e2fe01dd6f98da6cae8b07cd5cfa67abc70d97d ] Currently doing modprobe c_can_pci will make the kernel complain: Unbalanced pm_runtime_enable! this is caused by pm_runtime_enable() called before pm is initialized. This fix is similar to 227619c3ff7c, move those pm_enable/disable code to c_can_platform. Fixes: 4cdd34b26826 ("can: c_can: Add runtime PM support to Bosch C_CAN/D_CAN controller") Link: http://lore.kernel.org/r/20210302025542.987600-1-ztong0001@gmail.com Signed-off-by: Tong Zhang Tested-by: Uwe Kleine-König Signed-off-by: Marc Kleine-Budde Signed-off-by: Sasha Levin

can: c_can_pci: c_can_pci_remove(): fix use-after-free

2021-03-30T12:45:00Z

[ Upstream commit 0429d6d89f97ebff4f17f13f5b5069c66bde8138 ] There is a UAF in c_can_pci_remove(). dev is released by free_c_can_dev() and is used by pci_iounmap(pdev, priv->base) later. To fix this issue, save the mmio address before releasing dev. Fixes: 5b92da0443c2 ("c_can_pci: generic module for C_CAN/D_CAN on PCI") Link: https://lore.kernel.org/r/20210301024512.539039-1-ztong0001@gmail.com Signed-off-by: Tong Zhang Signed-off-by: Marc Kleine-Budde Signed-off-by: Sasha Levin

can: c_can: D_CAN: c_can_chip_config(): perform a sofware reset on open

2019-12-05T14:26:37Z

[ Upstream commit 23c5a9488f076bab336177cd1d1a366bd8ddf087 ] When the CAN interface is closed it the hardwre is put in power down mode, but does not reset the error counters / state. Reset the D_CAN on open, so the reported state and the actual state match. According to [1], the C_CAN module doesn't have the software reset. [1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf Signed-off-by: Jeroen Hofstee Signed-off-by: Marc Kleine-Budde Signed-off-by: Sasha Levin

can: c_can: c_can_poll(): only read status register after status IRQ

2019-11-12T18:13:22Z

commit 3cb3eaac52c0f145d895f4b6c22834d5f02b8569 upstream. When the status register is read without the status IRQ pending, the chip may not raise the interrupt line for an upcoming status interrupt and the driver may miss a status interrupt. It is critical that the BUSOFF status interrupt is forwarded to the higher layers, since no more interrupts will follow without intervention. Thanks to Wolfgang and Joe for bringing up the first idea. Signed-off-by: Kurt Van Dijck Cc: Wolfgang Grandegger Cc: Joe Burmeister Fixes: fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts") Cc: linux-stable Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: c_can: don't indicate triple sampling support for D_CAN

2017-11-15T16:13:13Z

commit fb5f0b3ef69b95e665e4bbe8a3de7201f09f1071 upstream. The D_CAN controller doesn't provide a triple sampling mode, so don't set the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling triple sampling is a no-op. Signed-off-by: Richard Schütz Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: c_can_pci: fix null-pointer-deref in c_can_start() - set device pointer

2017-02-01T07:30:52Z

commit c97c52be78b8463ac5407f1cf1f22f8f6cf93a37 upstream. The priv->device pointer for c_can_pci is never set, but it is used without a NULL check in c_can_start(). Setting it in c_can_pci_probe() like c_can_plat_probe() prevents c_can_pci.ko from crashing, with and without CONFIG_PM. This might also cause the pm_runtime_*() functions in c_can.c to actually be executed for c_can_pci devices - they are the only other place where priv->device is used, but they all contain a null check. Signed-off-by: Einar Jón Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: c_can: Update D_CAN TX and RX functions to 32 bit - fix Altera Cyclone access

2016-08-10T09:49:28Z

commit 427460c83cdf55069eee49799a0caef7dde8df69 upstream. When testing CAN write floods on Altera's CycloneV, the first 2 bytes are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also observed bytes 4 & 5 were corrupted in some cases. The D_CAN Data registers are 32 bits and changing from 16 bit writes to 32 bit writes fixes the problem. Testing performed on Altera CycloneV (D_CAN). Requesting tests on other C_CAN & D_CAN platforms. Reported-by: Richard Andrysek Signed-off-by: Thor Thayer Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: remove obsolete assignment for CAN protocol error type

2015-11-23T08:37:38Z

The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is initialized with zero in alloc_can_err_skb() anyway. So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we can remove the obsolete OR operation entirely. Signed-off-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde

can: fix assignment of error location in CAN error messages

2015-11-23T08:37:34Z

As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187 the assignment of the error location in CAN error messages had some bit wise overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines a single value which points to a location inside the CAN frame on the wire. This patch fixes the assignments for the error locations in error messages. Reported-by: Dan Carpenter Signed-off-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde

can: c_can: Fix default pinmux glitch at init

2015-07-12T18:57:42Z

The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN interface is down) causes a slight glitch on the pinctrl settings when used. Since commit ab78029 (drivers/pinctrl: grab default handles from device core), the device core will automatically set the default pins. This causes the pins to be momentarily set to the default and then to the sleep state in register_c_can_dev(). By adding an optional "enable" state, boards can set the default pin state to be disabled and avoid the glitch when the switch from default to sleep first occurs. If the "enable" state is not available c_can_pinctrl_select_state() falls back to using the "default" pinctrl state. [Roger Q] - Forward port to v4.2 and use pinctrl_get_select(). Signed-off-by: J.D. Schroeder Signed-off-by: Roger Quadros Reviewed-by: Grygorii Strashko Cc: linux-stable Signed-off-by: Marc Kleine-Budde