kernel.git/drivers/net/can/c_can, branch linux-4.12.y

drivers: net: generalize napi_complete_done()

2017-01-30T20:10:42Z

napi_complete_done() allows to opt-in for gro_flush_timeout, added back in linux-3.19, commit 3b47d30396ba ("net: gro: add a per device gro flush timer") This allows for more efficient GRO aggregation without sacrifying latencies. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller

can: c_can_pci: fix null-pointer-deref in c_can_start() - set device pointer

2017-01-18T11:58:26Z

The priv->device pointer for c_can_pci is never set, but it is used without a NULL check in c_can_start(). Setting it in c_can_pci_probe() like c_can_plat_probe() prevents c_can_pci.ko from crashing, with and without CONFIG_PM. This might also cause the pm_runtime_*() functions in c_can.c to actually be executed for c_can_pci devices - they are the only other place where priv->device is used, but they all contain a null check. Signed-off-by: Einar Jón Cc: linux-stable Signed-off-by: Marc Kleine-Budde

can: c_can: Update D_CAN TX and RX functions to 32 bit - fix Altera Cyclone access

2016-06-20T07:32:40Z

When testing CAN write floods on Altera's CycloneV, the first 2 bytes are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also observed bytes 4 & 5 were corrupted in some cases. The D_CAN Data registers are 32 bits and changing from 16 bit writes to 32 bit writes fixes the problem. Testing performed on Altera CycloneV (D_CAN). Requesting tests on other C_CAN & D_CAN platforms. Reported-by: Richard Andrysek Signed-off-by: Thor Thayer Cc: Signed-off-by: Marc Kleine-Budde

can: remove obsolete assignment for CAN protocol error type

2015-11-23T08:37:38Z

The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is initialized with zero in alloc_can_err_skb() anyway. So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we can remove the obsolete OR operation entirely. Signed-off-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde

can: fix assignment of error location in CAN error messages

2015-11-23T08:37:34Z

As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187 the assignment of the error location in CAN error messages had some bit wise overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines a single value which points to a location inside the CAN frame on the wire. This patch fixes the assignments for the error locations in error messages. Reported-by: Dan Carpenter Signed-off-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde

can: c_can: Fix default pinmux glitch at init

2015-07-12T18:57:42Z

The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN interface is down) causes a slight glitch on the pinctrl settings when used. Since commit ab78029 (drivers/pinctrl: grab default handles from device core), the device core will automatically set the default pins. This causes the pins to be momentarily set to the default and then to the sleep state in register_c_can_dev(). By adding an optional "enable" state, boards can set the default pin state to be disabled and avoid the glitch when the switch from default to sleep first occurs. If the "enable" state is not available c_can_pinctrl_select_state() falls back to using the "default" pinctrl state. [Roger Q] - Forward port to v4.2 and use pinctrl_get_select(). Signed-off-by: J.D. Schroeder Signed-off-by: Roger Quadros Reviewed-by: Grygorii Strashko Cc: linux-stable Signed-off-by: Marc Kleine-Budde

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2015-01-28T00:59:56Z

Conflicts: arch/arm/boot/dts/imx6sx-sdb.dts net/sched/cls_bpf.c Two simple sets of overlapping changes. Signed-off-by: David S. Miller

can: c_can: end pending transmission on network stop (ifdown)

2015-01-21T21:43:14Z

Put controller into init mode in network stop to end pending transmissions. The issue is observed in cases when transmitted frame is not acked. Signed-off-by: Viktor Babrian Cc: linux-stable Signed-off-by: Marc Kleine-Budde

can: move can_stats.bus_off++ from can_bus_off into can_change_state

2015-01-20T12:56:53Z

In order to be able to move the stats increment from can_bus_off() into can_change_state(), the increment had to be moved back into code that was using can_bus_off() but not can_change_state(). As a side-effect, this patch fixes the following bugs: * Redundant call to can_bus_off() in c_can. * Bus-off counted twice in xilinx_can. Signed-off-by: Andri Yngvason Signed-off-by: Marc Kleine-Budde

can: c_can: use regmap_update_bits() to modify RAMINIT register

2015-01-15T15:58:00Z

use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon() is not safe as the RAMINIT register can be shared between different drivers at least for TI SoCs. To make the modification atomic we switch to using regmap_update_bits(). regmap_update_bits() skips writing to the register if it's read content is the same as what is going to be written. This causes an issue for us when we need to clear the DONE bit with the initial condition START:0, DONE:1 as DONE bit must be written with 1 to clear it. So we defer the clearing of DONE bit to later when we set the START bit. There we are sure that START bit is changed from 0 to 1 so the write of 1 to already set DONE bit will happen. Signed-off-by: Roger Quadros Signed-off-by: Marc Kleine-Budde