kernel.git/drivers/mtd/maps/Kconfig, branch linux-5.4.y

mtd: fixup CFI on ixp4xx

2022-01-20T08:19:19Z

commit 603362b4a58393061dcfed1c7f0d0fd4aba61126 upstream. drivers/mtd/maps/ixp4xx.c requires MTD_CFI_BE_BYTE_SWAP to be set in order to compile. drivers/mtd/maps/ixp4xx.c:57:4: error: #error CONFIG_MTD_CFI_BE_BYTE_SWAP required This patch avoids the #error output by enforcing the policy in Kconfig. Not sure if this is the right approach, but it helps doing randconfig builds. Signed-off-by: Arnd Bergmann Acked-by: Linus Walleij Signed-off-by: Miquel Raynal Link: https://lore.kernel.org/linux-mtd/20210927141045.1597593-1-arnd@kernel.org Cc: Anders Roxell Signed-off-by: Greg Kroah-Hartman

treewide: Add SPDX license identifier - Makefile/Kconfig

2019-05-21T08:50:46Z

Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

mtd: maps: Allow MTD_PHYSMAP with MTD_RAM

2019-05-06T19:47:01Z

When the physmap_of_core.c code was merged into physmap-core.c the ability to use MTD_PHYSMAP_OF with only MTD_RAM selected was lost. Restore this by adding MTD_RAM to the dependencies of MTD_PHYSMAP. Fixes: commit 642b1e8dbed7 ("mtd: maps: Merge physmap_of.c into physmap-core.c") Cc: Signed-off-by: Chris Packham Reviewed-by: Hamish Martin Signed-off-by: Richard Weinberger

mtd: physmap_of_gemini: Handle pin control

2018-12-06T15:57:13Z

This enables the complex mapping for the Gemini and kicks in custom read/write functions that will wrap the existing simple functions in calls to enable/disable the parallel flash pins using pin controls. This is necessary on some hardware such as the D-Link DIR-685 where all flash pins are patched in/out at the same time, but some of the flash pins are in practice unused by the flash and have anyway been reused as GPIO. This concerns specifically CE1 on the Gemini. There is only one flash chip, so only CE0 is used, and the line for CE1 has been reused as chip select for the emulated SPI port connected to the display. If we try to use the same lines for flash and GPIO at the same time, one of them will loose: the GPIO line will disappear because it gets disconnected from the pin when the flash group is muxed out. Fix this by introducing two pin control states named simply "enabled" and "disabled" and only enable the flash lines when absolutely necessary (during read/write/copy). This way, they are available for GPIO at all other times and the display works. Collect all the state variables in a struct named struct gemini_flash and allocate this struct at probe time. Signed-off-by: Linus Walleij Signed-off-by: Boris Brezillon

mtd: maps: Get rid of the latch-addr-flash driver

2018-11-06T22:33:06Z

Looks like this driver was initially added to support the NOR on the DA830-EVM (Davinci) board, but the board file update was never merged. Keeping unused drivers just adds to the maintenance burden, so let's remove it if nobody uses it. Cc: David Griego Cc: Aleksey Makarov Cc: Sergei Shtylyov Cc: Savinay Dharmappa Signed-off-by: Boris Brezillon Acked-by: Sekhar Nori

mtd: maps: Merge gpio-addr-flash.c into physmap-core.c

2018-11-05T21:24:43Z

Controlling some MSB address lines using GPIOs is just a small deviation from the generic physmap logic, and merging those two drivers allows us to share most of the probe logic, which is a good thing. Also, the gpio-addr-flash driver is unused since the removal of the blackfin arch in v4.17, so we can safely remove the old driver without risking breaking existing boards. Signed-off-by: Boris Brezillon Reviewed-by: Ricardo Ribalda Delgado Tested-by: Ricardo Ribalda Delgado Acked-by: Linus Walleij

mtd: maps: Rename physmap_of_{versatile, gemini} into physmap-{versatile, gemini}

2018-11-05T21:24:29Z

Now that the physmap_of driver is gone, the gemini and versative extensions are part of the physmap driver. Rename the source files and the config option to reflect this. Signed-off-by: Boris Brezillon Reviewed-by: Ricardo Ribalda Delgado Acked-by: Linus Walleij

mtd: maps: Merge physmap_of.c into physmap-core.c

2018-11-05T21:24:24Z

There's no real reason to have two separate driver for the DT and pdata case. Just do what we do everywhere else and handle DT and pdata parsing in the same driver. Signed-off-by: Boris Brezillon Reviewed-by: Ricardo Ribalda Delgado Acked-by: Linus Walleij

mtd: Make Kconfig formatting consistent

2018-07-19T21:12:06Z

Fix indentation and replace '---help---' by 'help' to make things consistent. Signed-off-by: Boris Brezillon Reviewed-by: Miquel Raynal

mtd: maps: remove bfin-async-flash driver

2018-03-21T08:50:57Z

The blackfin architecture is getting removed, so this driver has become obsolete. Signed-off-by: Arnd Bergmann Signed-off-by: Boris Brezillon