kernel.git/drivers/mmc/core/sdio.c, branch linux-4.4.y

mmc: core: Enable tuning according to the actual timing

2016-03-03T23:07:15Z

commit e10c321977091f163eceedec0650e0ef4b3cf4bb upstream. While in sdhci_execute_tuning() the choice whether or not to enable the tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the check is done on the capability of the card. This difference is causing some issues with some SDIO cards in DDR50 mode where the CDM19 is wrongly issued. With this patch we modify the check in both mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision only according to the actual timing specification. Signed-off-by: Carlo Caione Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdio: Fix invalid vdd in voltage switch power cycle

2016-03-03T23:07:15Z

commit d9bfbb95ed598a09cf336adb0f190ee0ff802f0d upstream. The 'ocr' parameter passed to mmc_set_signal_voltage() defines the power-on voltage used when power cycling after a failure to set the voltage. However, in the case of mmc_sdio_init_card(), the value passed has the R4_18V_PRESENT flag set which is not valid for power-on and results in an invalid vdd. Fix by passing the card's ocr value which does not have the flag. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: core: Remove MMC_CLKGATE

2015-10-26T15:00:09Z

MMC_CLKGATE was once invented to save power by gating the bus clock at request inactivity. At that time it served its purpose. The modern way to deal with power saving for these scenarios, is by using runtime PM. Nowadays, several host drivers have deployed runtime PM, but for those that haven't and which still cares power saving at request inactivity, it's certainly time to deploy runtime PM as it has been around for several years now. To simplify code to mmc core and thus decrease maintenance efforts, this patch removes all code related to MMC_CLKGATE. Signed-off-by: Ulf Hansson Reviewed-by: Linus Walleij

mmc: core: Keep host claimed while invoking mmc_power_off|up()

2015-10-26T14:59:52Z

As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device, it's important that the host is kept claimed for *all* accesses to it via the host_ops callbacks. In some code paths for SDIO, particularly related to the PM support, mmc_power_off|up() is invoked without keeping the host claimed. Let's fix these. Moreover, mmc_start|stop_host() also invokes mmc_power_off|up() without claiming the host, let's fix these as well. Signed-off-by: Ulf Hansson Acked-by: Kishon Vijay Abraham I

mmc: core: Record card drive strength

2015-06-01T07:07:13Z

In preparation for adding drive strength support for eMMC, add drive_strength to struct mmc_card to record the card drive strength for UHS-I modes and HS200 / HS400. For eMMC this will be needed when switching between HS200 and HS400. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: core: Factor out common code in drive strength selection

2015-06-01T07:07:12Z

Make a new function out of common code used for drive strength selection. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: core: Add 'card' to drive strength selection callback

2015-06-01T07:07:12Z

In preparation for supporting also eMMC drive strength, add the 'card' as a parameter so that the callback can distinguish different types of cards if necessary. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: core: Simplify card drive strength mask

2015-06-01T07:07:11Z

Card drive strength selection uses a callback to which a mask of supported drive strengths is passed. Currently, the bits are checked against the values in the SD specifications. That is not necessary because the callback will anyway match the mask against a valid value. Simplify by taking the mask as is but still ensuring that the default mandatory value (type B) is always supported. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: core: Allow card drive strength to be different to host

2015-06-01T07:07:11Z

Initialization of UHS-I modes for SD and SDIO cards employs a callback to allow the host driver to choose a drive strength value. Currently that assumes the card drive strength and host driver type must be the same value. Change to let the callback make that decision and return both the card drive strength and host driver type. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: core: Enable / disable re-tuning

2015-06-01T07:06:54Z

Enable re-tuning when tuning is executed and disable re-tuning when card is no longer initialized. In the case of SDIO suspend, the card can keep power. In that case, re-tuning need not be disabled, but, if a re-tuning timer is being used, ensure it is disabled and assume that re-tuning will be needed upon resume since it is not known how long the suspend will last. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson