kernel.git/drivers/mmc/core/sdio.c, branch linux-3.1.y

mmc: core: Fix hangs related to insert/remove of cards

2011-11-11T17:42:27Z

commit 7f7e4129c23f0419257184dff6fec89d2d5a8964 upstream. During a rescan operation mmc_attach(sd|mmc|sdio) functions are called. The error handling in these function can trigger a detach of the bus, which also meant a power off. This is not notified by the rescan operation which then continues to the next attach function. If a power off has been done, the framework must never send any new commands to the host driver, without first doing a new power up. This will most likely trigger any host driver to hang. Moving power off out of detach and instead handle power off separately when it is actually needed, solves the issue. Signed-off-by: Ulf Hansson Acked-by: Linus Walleij Signed-off-by: Chris Ball Signed-off-by: Greg Kroah-Hartman

mmc: sdio: reset card during power_restore

2011-06-25T22:52:44Z

mmc_sdio_power_restore() skips some steps that are performed in other power-related codepaths which are necessary to fully reset the card. Without this, runtime PM fails for SD8686 SDIO wifi on OLPC XO-1.5. Signed-off-by: Daniel Drake Signed-off-by: Chris Ball

mmc: sd: add support for driver type selection

2011-05-25T03:53:24Z

This patch adds support for setting driver strength during UHS-I initialization procedure. Since UHS-I cards set S18A (bit 24) in response to ACMD41, we use this as a base for UHS-I initialization. We modify the parameter list of mmc_sd_get_cid() so that we can save the ROCR from ACMD41 to check whether bit 24 is set. We decide whether the Host Controller supports A, C, or D driver type depending on the Capabilities register. Driver type B is suported by default. We then set the appropriate driver type for the card using CMD6 mode 1. As per Host Controller spec v3.00, we set driver type for the host only if Preset Value Enable in the Host Control2 register is not set. SDHCI_HOST_CONTROL has been renamed to SDHCI_HOST_CONTROL1 to conform to the spec. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath Reviewed-by: Philip Rakity Tested-by: Philip Rakity Acked-by: Zhangfei Gao Signed-off-by: Chris Ball

mmc: quirks: Extends card quirks with MMC/SD quirks matching the CID.

2011-05-25T01:00:54Z

The current mechanism is SDIO-only. This allows us to create function-specific quirks, without creating messy Kconfig dependencies, or polluting core/ with function-specific code. Signed-off-by: Andrei Warkentin Acked-by: Arnd Bergmann Signed-off-by: Chris Ball

mmc: add MMC_QUIRK_DISABLE_CD

2011-05-25T01:00:01Z

006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up resistor on CD/DAT[3] (pin 1) of the card. Make it possible to start using sdio_disable_cd() by introducing MMC_QUIRK_DISABLE_CD. Signed-off-by: Ohad Ben-Cohen Signed-off-by: Chris Ball

mmc: add MMC_QUIRK_NONSTD_FUNC_IF

2011-05-25T00:59:52Z

Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function interface code" as indicated by the card's FBR, and instead treat all functions as non-standard interfaces. This is required to prevent standard drivers from facing errors when trying to communicate with SDIO cards that erroneously indicate standard function interface codes. Signed-off-by: Ohad Ben-Cohen Signed-off-by: Chris Ball

mmc: do not switch to 1-bit mode if not required

2011-05-25T00:59:47Z

6b5eda36 followed SDIO spec part E1 section 8, which states that in case SDIO interrupts are being used to wake up a suspended host, then it is required to switch to 1-bit mode before stopping the clock. Before switching to 1-bit mode (or back to 4-bit mode on resume), make sure that SDIO interrupts are really being used to wake the host. This is helpful for devices which have an external irq line (e.g. wl1271), and do not use SDIO interrupts to wake up the host. In this case, switching to 1-bit mode (and back to 4-bit mode on resume) is not necessary. Reported-by: Eliad Peller Signed-off-by: Ohad Ben-Cohen Signed-off-by: Chris Ball

mmc: mmc_card_keep_power cleanups

2011-05-25T00:59:43Z

mmc_card_is_powered_resumed is a mouthful; instead, simply use mmc_card_keep_power, which also better explains the purpose of the macro. Employ mmc_card_keep_power() where possible. Signed-off-by: Ohad Ben-Cohen Signed-off-by: Chris Ball

mmc: sdio: remember new card RCA when redetecting card

2011-03-17T19:35:09Z

During redetection of a SDIO card, a request for a new card RCA was submitted to the card, but was then overwritten by the old RCA. This caused the card to be deselected instead of selected when using the incorrect RCA. This bug's been present since the "oldcard" handling was introduced in 2.6.32. Signed-off-by: Stefan Nilsson XK Reviewed-by: Ulf Hansson Reviewed-by: Pawel Wieczorkiewicz Signed-off-by: Linus Walleij Cc: Signed-off-by: Chris Ball

mmc: add per device quirk placeholder

2011-03-15T17:48:33Z

Some cards have quirks valid for every platforms using current platform quirk hooks leads to a lot of code and debug duplication. So we inspire a bit from what exists in PCI subsystem and do our own per vendorid/deviceid quirk. We still drop the complexity of the pci quirk system (with special section tables, and so on). That can be added later if needed. Signed-off-by: Pierre Tardy Acked-by: Linus Walleij Acked-by: Ohad Ben-Cohen Signed-off-by: Chris Ball